Document Outline
- FEATURES
- APPLICATIONS
- GENERAL DESCRIPTION
- FUNCTIONAL BLOCK DIAGRAM
- PRODUCT HIGHLIGHTS
- SPECIFICATIONS
- TIMING SPECIFICATIONS
- ABSOLUTE MAXIMUM RATINGS
- ORDERING GUIDE
- PIN CONFIGURATION
- PIN FUNCTION DESCRIPTIONS
- TERMINOLOGY
- Integral Nonlinearity
- Differential Nonlinearity
- Offset Error
- Gain Error
- Track-and-Hold Acquisition Time
- Signal-to-(Noise + Distortion) Ratio
- Total Unadjusted Error
- Total Harmonic Distortion (THD)
- Peak Harmonic or Spurious Noise
- Intermodulation Distortion
- Typical Performance Characteristics
- CIRCUIT INFORMATION
- CONVERTER OPERATION
- ADC TRANSFER FUNCTION
- TYPICAL CONNECTION DIAGRAM
- Analog Input
- Digital Inputs
- MODES OF OPERATION
- Normal Mode
- Power-Down Mode
- Power-Up Time
- POWER VS. THROUGHPUT RATE
- SERIAL INTERFACE
- MICROPROCESSOR INTERFACING
- AD7476/AD7477/AD7478 to TMS320C5x/C54x Interface
- AD7476/AD7477/AD7478 to ADSP-21xx Interface
- AD7476/AD7477/AD7478 to DSP56xxx Interface
- AD7476/AD7477/AD7478 to MC68HC16 Interface
- OUTLINE DIMENSIONS
- Revision History
REV. D
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
2004 Analog Devices, Inc. All rights reserved.
AD7476/AD7477/AD7478
*
1 MSPS, 12-/10-/8-Bit ADCs
in 6-Lead SOT-23
*Protected by U.S.Patent No. 6,681,332.
FEATURES
Fast Throughput Rate: 1 MSPS
Specified for V
DD
of 2.35 V to 5.25 V
Low Power:
3.6 mW Typ at 1 MSPS with 3 V Supplies
15 mW Typ at 1 MSPS with 5 V Supplies
Wide Input Bandwidth:
70 dB SNR at 100 kHz Input Frequency
Flexible Power/Serial Clock Speed Management
No Pipeline Delays
High Speed Serial Interface
SPI
/QSPITM/MICROWIRETM/DSP Compatible
Standby Mode: 1 A Max
6-Lead SOT-23 Package
APPLICATIONS
Battery-Powered Systems
Personal Digital Assistants
Medical Instruments
Mobile Communications
Instrumentation and Control Systems
Data Acquisition Systems
High Speed Modems
Optical Sensors
FUNCTIONAL BLOCK DIAGRAM
T/H
AD7476/AD7477/AD7478
SCLK
SDATA
CS
V
IN
V
DD
GND
8-/10-/12-BIT
SUCCESSIVE-
APPROXIMATION
ADC
CONTROL
LOGIC
GENERAL DESCRIPTION
The AD7476/AD7477/AD7478 are, respectively, 12-bit, 10-bit,
and 8-bit, high speed, low power, successive-approximation
ADCs. The parts operate from a single 2.35 V to 5.25 V power
supply and feature throughput rates up to 1 MSPS. The parts
contain a low noise, wide bandwidth track-and-hold amplifier
that can handle input frequencies in excess of 6 MHz.
The conversion process and data acquisition are controlled
using
CS and the serial clock, allowing the devices to interface
with microprocessors or DSPs. The input signal is sampled on
the falling edge of
CS and the conversion is also initiated at this
point. There are no pipeline delays associated with the part.
The AD7476/AD7477/AD7478 use advanced design techniques
to achieve very low power dissipation at high throughput rates.
The reference for the part is taken internally from V
DD
.
This
allows the widest dynamic input range to the ADC. Thus the
analog input range for the part is 0 V to V
DD
. The conversion
rate is determined by the SCLK.
PRODUCT HIGHLIGHTS
1. First 12-/10-/8-Bit ADCs in a SOT-23 Package.
2. High Throughput with Low Power Consumption.
3. Flexible Power/Serial Clock Speed Management.
The conversion rate is determined by the serial clock, allowing
the conversion time to be reduced through the serial clock
speed increase. This allows the average power consumption
to be reduced while not converting. The part also features a
shutdown mode to maximize power efficiency at lower
throughput rates. Current consumption is 1
A maximum
when in shutdown.
4. Reference Derived from the Power Supply.
5. No Pipeline Delay.
The parts feature a standard successive-approximation ADC
with accurate control of the sampling instant via a
CS input
and once-off conversion control.
REV. D
2
AD7476SPECIFICATIONS
1
(A Version: V
DD
= 2.7 V to 5.25 V, f
SCLK
= 20 MHz, f
SAMPLE
= 1 MSPS, unless otherwise
noted; S and B Versions: V
DD
= 2.35 V to 5.25 V, f
SCLK
= 12 MHz, f
SAMPLE
= 600 kSPS,
unless otherwise noted; T
A
= T
MIN
to T
MAX
, unless otherwise noted.)
Parameter
A Version
1, 2
B Version
1, 2
S Version
1, 2
Unit
Test Conditions/Comments
DYNAMIC PERFORMANCE
f
IN
= 100 kHz Sine Wave
Signal-to-(Noise + Distortion) (SINAD)
3
69
70
69
dB min
B Version, V
DD
= 2.4 V to 5.25 V
70
70
dB min
T
A
= 25
C
71.5
dB typ
Signal-to-Noise Ratio (SNR)
3
70
71
70
dB min
B Version, V
DD
= 2.4 V to 5.25 V
72.5
dB typ
Total Harmonic Distortion (THD)
3
80
78
78
dB typ
Peak Harmonic or Spurious Noise (SFDR)
3
82
80
80
dB typ
Intermodulation Distortion (IMD)
3
Second-Order Terms
78
78
78
dB typ
fa = 103.5 kHz, fb = 113.5 kHz
Third-Order Terms
78
78
78
dB typ
fa = 103.5 kHz, fb = 113.5 kHz
Aperture Delay
10
10
10
ns typ
Aperture Jitter
30
30
30
ps typ
Full Power Bandwidth
6.5
6.5
6.5
MHz typ
@ 3 dB
DC ACCURACY
S, B Versions, V
DD
= (2.35 V to 3.6 V)
4
;
A Version, V
DD
= (2.7 V to 3.6 V)
Resolution
12
12
12
Bits
Integral Nonlinearity
3
1.5
1.5
LSB max
1
0.6
0.6
LSB typ
Differential Nonlinearity
3
0.9/+1.5
0.9/+1.5
LSB max
Guaranteed No Missed Codes to 12 Bits
0.75
0.75
0.75
LSB typ
Offset Error
3
1.5
2
LSB max
0.5
LSB typ
Gain Error
3
1.5
2
LSB max
0.5
LSB typ
ANALOG INPUT
Input Voltage Ranges
0 to V
DD
0 to V
DD
0 to V
DD
V
DC Leakage Current
1
1
1
A max
Input Capacitance
30
30
30
pF typ
LOGIC INPUTS
Input High Voltage, V
INH
2.4
2.4
2.4
V min
1.8
1.8
1.8
V min
V
DD
= 2.35 V
Input Low Voltage, V
INL
0.4
0.4
0.4
V max
V
DD
= 3 V
0.8
0.8
0.8
V max
V
DD
= 5 V
Input Current, I
IN
, SCLK Pin
1
1
1
A max
Typically 10 nA, V
IN
= 0 V or V
DD
Input Current, I
IN
,
CS Pin
1
1
1
A typ
Input Capacitance, C
IN
5
10
10
10
pF max
LOGIC OUTPUTS
Output High Voltage, V
OH
V
DD
0.2
V
DD
0.2
V
DD
0.2
V min
I
SOURCE
= 200
A; V
DD
= 2.35 V to 5.25 V
Output Low Voltage, V
OL
0.4
0.4
0.4
V max
I
SINK
= 200
A
Floating-State Leakage Current
10
10
10
A max
Floating-State Output Capacitance
5
10
10
10
pF max
Output Coding
Straight (Natural) Binary
CONVERSION RATE
Conversion Time
0.8
1.33
1.33
s max
16 SCLK Cycles
Track-and-Hold Acquisition Time
500
500
500
ns max
Full-Scale Step Input
350
400
400
ns max
Sine Wave Input
100 kHz
Throughput Rate
1000
600
600
kSPS max
See Serial Interface Section
POWER REQUIREMENTS
V
DD
2.35/5.25
2.35/5.25
2.35/5.25
V min/max
I
DD
Digital I/Ps = 0 V or V
DD
Normal Mode (Static)
2
2
2
mA typ
V
DD
= 4.75 V to 5.25 V. SCLK On or Off
1
1
1
mA typ
V
DD
= 2.35 V to 3.6 V. SCLK On or Off
Normal Mode (Operational)
3.5
3
3
mA max
V
DD
= 4.75 V to 5.25 V; f
SAMPLE
= f
SAMPLE
MAX
6
1.6
1.4
1.4
mA max
V
DD
= 2.35 V to 3.6 V; f
SAMPLE
= f
SAMPLE
MAX
6
Full Power-Down Mode
1
1
1
A max
SCLK Off
80
80
80
A max
SCLK On
Power Dissipation
7
Normal Mode (Operational)
17.5
15
15
mW max
V
DD
= 5 V; f
SAMPLE
= f
SAMPLE
MAX
6
4.8
4.2
4.2
mW max
V
DD
= 3 V; f
SAMPLE
= f
SAMPLE
MAX
6
Full Power-Down
5
5
5
W max
V
DD
= 5 V; SCLK Off
3
3
3
W max
V
DD
= 3 V; SCLK Off
NOTES
1
Temperature ranges as follows: A, B Versions: 40
C to +85C; S Version: 55C to +125C.
2
Operational from V
DD
= 2.0 V.
3
See Terminology section.
4
Maximum B, S version specifications apply as typical figures when V
DD
= 5.25 V.
5
Guaranteed by characterization.
6
A Version: f
SAMPLE
MAX = 1 MSPS; B, S Versions: f
SAMPLE
MAX = 600 kSPS.
7
See Power vs. Throughput Rate section.
Specifications subject to change without notice.
REV. D
3
AD7477SPECIFICATIONS
1
(V
DD
= 2.7 V to 5.25 V, f
SCLK
= 20 MHz, T
A
= T
MIN
to T
MAX
, unless otherwise noted.)
Parameter
A Version
1, 2
S Version
1, 2
Unit
Test Conditions/Comments
DYNAMIC PERFORMANCE
f
IN
= 100 kHz Sine Wave, f
SAMPLE
= 1 MSPS
Signal-to-(Noise + Distortion) (SINAD)
61
61
dB min
Total Harmonic Distortion (THD)
73
73
dB max
Peak Harmonic or Spurious Noise (SFDR)
74
74
dB max
Intermodulation Distortion (IMD)
Second-Order Terms
78
78
dB typ
fa = 103.5 kHz, fb = 113.5 kHz
Third-Order Terms
78
78
dB typ
fa = 103.5 kHz, fb = 113.5 kHz
Aperture Delay
10
10
ns typ
Aperture Jitter
30
30
ps typ
Full Power Bandwidth
6.5
6.5
MHz typ
@ 3 dB
DC ACCURACY
Resolution
10
10
Bits
Integral Nonlinearity
1
1
LSB max
Differential Nonlinearity
0.9
0.9
LSB max
Guaranteed No Missed Codes to 10 Bits
Offset Error
1
1
LSB max
Gain Error
1
1
LSB max
ANALOG INPUT
Input Voltage Ranges
0 to V
DD
0 to V
DD
V
DC Leakage Current
1
1
A max
Input Capacitance
30
30
pF typ
LOGIC INPUTS
Input High Voltage, V
INH
2.4
2.4
V min
Input Low Voltage, V
INL
0.8
0.8
V max
V
DD
= 5 V
0.4
0.4
V max
V
DD
= 3 V
Input Current, I
IN
, SCLK Pin
1
1
A max
Typically 10 nA, V
IN
= 0 V or V
DD
Input Current, I
IN
,
CS Pin
1
1
A typ
Input Capacitance, C
IN
4
10
10
pF max
LOGIC OUTPUTS
Output High Voltage, V
OH
V
DD
0.2
V
DD
0.2
V min
I
SOURCE
= 200
A; V
DD
= 2.7 V to 5.25 V
Output Low Voltage, V
OL
0.4
0.4
V max
I
SINK
= 200
A
Floating-State Leakage Current
10
10
A max
Floating-State Output Capacitance
4
10
10
pF max
Output Coding
Straight (Natural) Binary
CONVERSION RATE
Conversion Time
800
800
ns max
16 SCLK Cycles with SCLK at 20 MHz
Track-and-Hold Acquisition Time
400
400
ns max
Throughput Rate
1
1
MSPS max
See Serial Interface Section
POWER REQUIREMENTS
V
DD
2.7/5.25
2.7/5.25
V min/max
I
DD
Digital I/Ps = 0 V or V
DD
Normal Mode (Static)
2
2
mA typ
V
DD
= 4.75 V to 5.25 V; SCLK On or Off
1
1
mA typ
V
DD
= 2.7 V to 3.6 V; SCLK On or Off
Normal Mode (Operational)
3.5
3.5
mA max
V
DD
= 4.75 V to 5.25 V; f
SAMPLE
= 1 MSPS
1.6
1.6
mA max
V
DD
= 2.7 V to 3.6 V; f
SAMPLE
= 1 MSPS
Full Power-Down Mode
1
1
A max
SCLK Off
80
80
A max
SCLK On
Power Dissipation
5
Normal Mode (Operational)
17.5
17.5
mW max
V
DD
= 5 V; f
SAMPLE
= 1 MSPS
4.8
4.8
mW max
V
DD
= 3 V; f
SAMPLE
= 1 MSPS
Full Power-Down
5
5
W max
V
DD
= 5 V; SCLK Off
NOTES
1
Temperature ranges as follows: A Version: 40
C to +85C; S Version: 55C to +125C.
2
Operational from V
DD
= 2.0 V, with input high voltage, V
INH
= 1.8 V min.
3
See Terminology section.
4
Guaranteed by characterization.
5
See Power vs. Throughput Rate section.
Specifications subject to change without notice.
REV. D
4
AD7476SPECIFICATIONS
1
(V
DD
= 2.7 V to 5.25 V, f
SCLK
= 20 MHz, T
A
= T
MIN
to T
MAX
, unless otherwise noted.)
Parameter
A Version
1, 2
S Version
1, 2
Unit
Test Conditions/Comments
DYNAMIC PERFORMANCE
f
IN
= 100 kHz Sine Wave, f
SAMPLE
= 1 MSPS
Signal-to-(Noise + Distortion) (SINAD)
49
49
dB min
Total Harmonic Distortion (THD)
65
65
dB max
Peak Harmonic or Spurious Noise (SFDR)
65
65
dB max
Intermodulation Distortion (IMD)
Second-Order Terms
68
68
dB typ
fa = 498.7 kHz, fb = 508.7 kHz
Third-Order Terms
68
68
dB typ
fa = 498.7 kHz, fb = 508.7 kHz
Aperture Delay
10
10
ns typ
Aperture Jitter
30
30
ps typ
Full Power Bandwidth
6.5
6.5
MHz typ
@ 3 dB
DC ACCURACY
Resolution
8
8
Bits
Integral Nonlinearity
0.5
0.5
LSB max
Differential Nonlinearity
0.5
0.5
LSB max
Guaranteed No Missed Codes to Eight Bits
Offset Error
0.5
0.5
LSB max
Gain Error
0.5
0.5
LSB max
Total Unadjusted Error (TUE)
0.5
0.5
LSB max
ANALOG INPUT
Input Voltage Ranges
0 to V
DD
0 to V
DD
V
DC Leakage Current
1
1
A max
Input Capacitance
30
30
pF typ
LOGIC INPUTS
Input High Voltage, V
INH
2.4
2.4
V min
Input Low Voltage, V
INL
0.8
0.8
V max
V
DD
= 5 V
0.4
0.4
V max
V
DD
= 3 V
Input Current, I
IN
, SCLK Pin
1
1
A max
Typically 10 nA, V
IN
= 0 V or V
DD
Input Current, I
IN
,
CS Pin
1
1
A typ
Input Capacitance, C
IN
4
10
10
pF max
LOGIC OUTPUTS
Output High Voltage, V
OH
V
DD
0.2
V
DD
0.2
V min
I
SOURCE
= 200
A; V
DD
= 2.7 V to 5.25 V
Output Low Voltage, V
OL
0.4
0.4
V max
I
SINK
= 200
A
Floating-State Leakage Current
10
10
A max
Floating-State Output Capacitance
4
10
10
pF max
Output Coding
Straight (Natural) Binary
CONVERSION RATE
Conversion Time
800
800
ns max
16 SCLK Cycles with SCLK at 20 MHz
Track-and-Hold Acquisition Time
400
400
ns max
Throughput Rate
1
1
MSPS max
See Serial Interface Section
POWER REQUIREMENTS
V
DD
2.7/5.25
2.7/5.25
V min/max
I
DD
Digital I/Ps = 0 V or V
DD
Normal Mode (Static)
2
2
mA typ
V
DD
= 4.75 V to 5.25 V; SCLK On or Off
1
1
mA typ
V
DD
= 2.7 V to 3.6 V; SCLK On or Off
Normal Mode (Operational)
3.5
3.5
mA max
V
DD
= 4.75 V to 5.25 V; f
SAMPLE
= 1 MSPS
1.6
1.6
mA max
V
DD
= 2.7 V to 3.6 V; f
SAMPLE
= 1 MSPS
Full Power-Down Mode
1
1
A max
SCLK Off
80
80
A max
SCLK On
Power Dissipation
5
Normal Mode (Operational)
17.5
17.5
mW max
V
DD
= 5 V; f
SAMPLE
= 1 MSPS
4.8
4.8
mW max
V
DD
= 3 V; f
SAMPLE
= 1 MSPS
Full Power-Down
5
5
W max
V
DD
= 5 V; SCLK Off
NOTES
1
Temperature ranges as follows: A Version: 40
C to +85C; S Version: 55C to +125C.
2
Operational from V
DD
= 2.0 V, with input high voltage, V
INH
= 1.8 V min.
3
See Terminology section.
4
Guaranteed by characterization.
5
See Power vs. Throughput Rate section.
Specifications subject to change without notice.
8
REV. D
AD7476/AD7477/AD7478
5
TIMING SPECIFICATIONS
1, 2
(V
DD
= 2.35 V to 5.25 V, T
A
= T
MIN
to T
MAX
, unless otherwise noted.)
Limit at T
MIN
, T
MAX
AD7476/AD7477/AD7478
Parameter
3 V
3
5 V
3
Unit
Description
f
SCLK
4
10
10
kHz min
20
20
MHz max
A Version
12
12
MHz max
B Version
t
CONVERT
16
t
SCLK
16
t
SCLK
t
QUIET
50
50
ns min
Minimum Quiet Time Required between Bus Relinquish and
Start of Next Conversion
t
1
10
10
ns min
Minimum
CS Pulsewidth
t
2
10
10
ns min
CS to SCLK Setup Time
t
3
5
20
20
ns max
Delay from
CS until SDATA Three-State Disabled
t
4
5
40
20
ns max
Data Access Time after SCLK Falling Edge, A Version
70
20
ns max
Data Access Time after SCLK Falling Edge, B Version
t
5
0.4
t
SCLK
0.4
t
SCLK
ns min
SCLK Low Pulsewidth
t
6
0.4
t
SCLK
0.4
t
SCLK
ns min
SCLK High Pulsewidth
t
7
10
10
ns min
SCLK to Data Valid Hold Time
t
8
6
10
10
ns min
SCLK Falling Edge to SDATA High Impedance
25
25
ns max
SCLK Falling Edge to SDATA High Impedance
t
POWER-UP
7
1
1
s typ
Power-Up Time from Full Power-Down
NOTES
1
Guaranteed by characterization. All input signals are specified with tr = tf = 5 ns (10% to 90% of V
DD
) and timed from a voltage level of 1.6 V.
2
A Version timing specifications apply to the AD7477 S Version and AD7478 S Version; B Version timing specifications apply to the AD7476 S Version.
3
3 V specifications apply from V
DD
= 2.7 V to 3.6 V for A Version; 3 V specifications apply from V
DD
= 2.35 V to 3.6 V for B Version; 5 V specifications apply from
V
DD
= 4.75 V to 5.25 V.
4
Mark/Space ratio for the SCLK input is 40/60 to 60/40.
5
Measured with the load circuit of Figure 1 and defined as the time required for the output to cross 0.8 V or 2.0 V.
6
t
8
is derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then extrapolated
to remove the effects of charging or discharging the 50 pF capacitor. This means that the time, t
8
, quoted in the Timing Specifications is the true bus relinquish time
of the part and is independent of the bus loading.
7
See Power-Up Time section.
Specifications subject to change without notice.
200 A
I
OL
200 A
I
OH
C
L
50pF
TO OUTPUT
PIN
1.6V
Figure 1. Load Circuit for Digital Output Timing
Specifications
REV. D
6
AD7476/AD7477/AD7478
ABSOLUTE MAXIMUM RATINGS
1
(T
A
= 25
C, unless otherwise noted.)
V
DD
to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3 V to +7 V
Analog Input Voltage to GND . . . . . . . . 0.3 V to V
DD
+ 0.3 V
Digital Input Voltage to GND . . . . . . . . . . . . . . 0.3 V to +7 V
Digital Output Voltage to GND . . . . . . 0.3 V to V
DD
+ 0.3 V
Input Current to Any Pin Except Supplies
2
. . . . . . . .
10 mA
Operating Temperature Range
Commercial (A, B Versions) . . . . . . . . . . . 40
C to +85C
Military (S Version) . . . . . . . . . . . . . . . . . . 55
C to +125C
Storage Temperature Range . . . . . . . . . . . . 65
C to +150C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150
C
SOT-23 Package
JA
Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 230
C/W
JC
Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . 92
C/W
Lead Temperature, Soldering
Reflow (10 sec to 30 sec) . . . . . . . . . . . . . . . . 235 (0/+5)
C
Pb-Free Temperature Soldering
Reflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 (0/+5)
C
ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5 kV
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
Transient currents of up to 100 mA will not cause SCR latch-up.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although the
AD7476/AD7477/AD7478 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions
are recommended to avoid performance degradation or loss of functionality.
ORDERING GUIDE
Temperature
Linearity
Package
Branding
Model
Range
Error (LSB)
1
Option
2
Information
AD7476ART-500RL7
40
C to +85C
1 typ
RT-6
CEA
AD7476ART-REEL
40
C to +85C
1 typ
RT-6
CEA
AD7476ART-REEL7
40
C to +85C
1 typ
RT-6
CEA
AD7476ARTZ-500RL7
3
40
C to +85C
1 typ
RT-6
CEA
AD7476ARTZ-REEL
3
40
C to +85C
1 typ
RT-6
CEA
AD7476ARTZ-REEL7
3
40
C to +85C
1 typ
RT-6
CEA
AD7476BRT-REEL
40
C to +85C
1.5 max
RT-6
CEB
AD7476BRT-REEL7
40
C to +85C
1.5 max
RT-6
CEB
AD7476BRTZ-REEL
3
40
C to +85C
1.5 max
RT-6
CEB
AD7476BRTZ-REEL7
3
40
C to +85C
1.5 max
RT-6
CEB
AD7476SRT-500RL7
55
C to +125C
1.5 max
RT-6
CES
AD7476SRT-R2
55
C to +125C
1.5 max
RT-6
CES
AD7476SRT-REEL
55
C to +125C
1.5 max
RT-6
CES
AD7476SRT-REEL7
55
C to +125C
1.5 max
RT-6
CES
AD7476SRTZ-500RL7
3
55
C to +125C
1.5 max
RT-6
CES
AD7476SRTZ-R2
3
55
C to +125C
1.5 max
RT-6
CES
AD7476SRTZ-REEL
3
55
C to +125C
1.5 max
RT-6
CES
AD7476SRTZ-REEL7
3
55
C to +125C
1.5 max
RT-6
CES
AD7477ART-500RL7
40
C to +85C
1 max
RT-6
CFA
AD7477ART-REEL
40
C to +85C
1 max
RT-6
CFA
AD7477ART-REEL7
40
C to +85C
1 max
RT-6
CFA
AD7477SRT-500RL7
55
C to +125C
1 max
RT-6
CFS
AD7477SRT-R2
55
C to +125C
1 max
RT-6
CFS
AD7477SRT-REEL
55
C to +125C
1 max
RT-6
CFS
AD7477SRT-REEL7
55
C to +125C
1 max
RT-6
CFS
AD7478ART-500RL7
40
C to +85C
0.5 max
RT-6
CJA
AD7478ART-REEL
40
C to +85C
0.5 max
RT-6
CJA
AD7478ART-REEL7
40
C to +85C
0.5 max
RT-6
CJA
AD7478SRT-500RL7
55
C to +125C
0.5 max
RT-6
CJS
AD7478SRT-R2
55
C to +125C
0.5 max
RT-6
CJS
AD7478SRT-REEL7
55
C to +125C
0.5 max
RT-6
CJS
EVAL-AD7476CB
4
Evaluation Board
EVAL-AD7477CB
4
Evaluation Board
EVAL-CONTROL BRD2
5
Control Board
NOTES
1
Linearity Error here refers to integral linearity error.
2
RT = SOT-23.
3
Z = Pb free.
4
This can be used as a standalone evaluation board or in conjunction with the EVAL-CONTROL BOARD for evaluation/demonstration purposes.
5
This board is a complete unit allowing a PC to control and communicate with all Analog Devices evaluation boards ending in the CB designators. To order a complete
evaluation kit, you need to order the particular ADC evaluation board, e.g., EVAL-AD7476CB, the EVAL-CONTROL BRD2, and a 12 V ac transformer. See relevant
evaluation board application note for more information.
REV. D
AD7476/AD7477/AD7478
7
PIN CONFIGURATION
TOP VIEW
(Not to Scale)
6
5
4
1
2
3
V
DD
GND
V
IN
CS
SDATA
SCLK
AD7476/
AD7477/
AD7478
PIN FUNCTION DESCRIPTIONS
Pin
No.
Mnemonic
Function
1
V
DD
Power Supply Input. The V
DD
range for the AD7476/AD7477/AD7478 is from 2.35 V to 5.25 V.
2
GND
Analog Ground. Ground reference point for all circuitry on the AD7476/AD7477/AD7478. All analog
input signals should be referred to this GND voltage.
3
V
IN
Analog Input. Single-ended analog input channel. The input range is 0 V to V
DD
.
4
SCLK
Serial Clock. Logic input. SCLK provides the serial clock for accessing data from the part. This clock
input is also used as the clock source for the AD7476/AD7477/AD7478's conversion process.
5
SDATA
Data Out. Logic output. The conversion result from the AD7476/AD7477/AD7478 is provided on
this output as a serial data stream. The bits are clocked out on the falling edge of the SCLK input. The
data stream from the AD7476 consists of four leading zeros followed by the 12 bits of conversion data,
which is provided MSB first; the data stream from the AD7477 consists of four leading zeros followed
by the 10 bits of conversion data, followed by two trailing zeros, which is also provided MSB first; the
data stream from the AD7478 consists of four leading zeros followed by the eight bits of conversion
data, followed by four trailing zeros, which is provided MSB first.
6
CS
Chip Select. Active low logic input. This input provides the dual function of initiating conversions on
the AD7476/AD7477/AD7478 and framing the serial data transfer.
REV. D
8
AD7476/AD7477/AD7478
TERMINOLOGY
Integral Nonlinearity
This is the maximum deviation from a straight line passing through
the endpoints of the ADC transfer function. For the AD7476/
AD7477, the endpoints of the transfer function are zero scale, a
point 1/2 LSB below the first code transition, and full scale, a
point 1/2 LSB above the last code transition. For the AD7478, the
endpoints of the transfer function are zero scale, a point 1 LSB
below the first code transition, and full scale, a point 1 LSB above
the last code transition.
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Offset Error
This is the deviation of the first code transition (00 . . . 000)
to (00 . . . 001) from the ideal (i.e., AGND + 0.5 LSB). For
the AD7478, this is the deviation of the first code transition
(00 . . . 000) to (00 . . . 001) from the ideal (i.e., AGND + 1 LSB).
Gain Error
For the AD7476/AD7477, this is the deviation of the last code
transition (111 . . . 110) to (111 . . . 111) from the ideal (i.e.,
V
REF
1.5 LSB) after the offset error has been adjusted out. For
the AD7478, this is the deviation of the last code transition
(111 . . . 110) to (111 . . . 111) from the ideal (i.e., V
REF
1 LSB)
after the offset error has been adjusted.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns into track mode after the
end of conversion. Track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within
0.5 LSB, after the end of conversion. See
the Serial Interface Timing section for more detail.
Signal-to-(Noise + Distortion) Ratio
This is the measured ratio of signal-to-(noise + distortion) at the
output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals up
to half the sampling frequency (f
S
/2), excluding dc.
The ratio is dependent on the number of quantization levels in
the digitization process; the more levels, the smaller the quanti-
zation noise. The theoretical signal-to-(noise + distortion) ratio
for an ideal N-bit converter with a sine wave input is given by
Signal-to-(Noise + Distortion) = (6.02N + 1.76) dB
Thus for a 12-bit converter, this is 74 dB; for a 10-bit converter
it is 62 dB; and for an 8-bit converter it is 50 dB.
Total Unadjusted Error
This is a comprehensive specification that includes gain error,
linearity error, and offset error.
Total Harmonic Distortion (THD)
Total harmonic distortion is the ratio of the rms sum of harmon-
ics to the fundamental. For the AD7476/AD7477/AD7478, it is
defined as:
THD
V
V
V
V
V
V
2
2
3
2
4
2
5
2
6
2
1
(
)
log
(
)
dB
=
+
+
+
+
20
where V
1
is the rms amplitude of the fundamental and V
2
, V
3
,
V
4
, V
5
, and V
6
are the rms amplitudes of the second through the
sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to f
S
/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is deter-
mined by the largest harmonic in the spectrum, but for ADCs
where the harmonics are buried in the noise floor, it will be a
noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities will create distortion
products at sum and difference frequencies of mfa
nfb where
m, n = 0, 1, 2, 3, and so on. Intermodulation distortion terms
are those for which neither m nor n is equal to zero. For example,
the second-order terms include (fa + fb) and (fa fb), while the
third-order terms include (2fa + fb), (2fa fb), (fa + 2fb), and
(fa 2fb).
The AD7476/AD7477/AD7478 are tested using the CCIF
standard where two input frequencies are used, fa = 498.7 kHz and
fb = 508.7 kHz. In this case, the second-order terms are usually
distanced in frequency from the original sine waves while the
third-order terms are usually at a frequency close to the input
frequencies. As a result, the second- and third-order terms are
specified separately. The calculation of the intermodulation
distortion is as per the THD specification where it is the ratio of
the rms sum of the individual distortion products to the rms
amplitude of the sum of the fundamentals, expressed in dB.
REV. D
Typical Performance CharacteristicsAD7476/AD7477/AD7478
9
FREQUENCY kHz
0
SNR dB
50
100
150
200
250
300
350
400
450
500
15
35
55
75
95
115
8192 POINT FFT
f
SAMPLE
= 1MSPS
f
IN
= 100kHz
SINAD = 71.67dB
THD = 81.00dB
SFDR = 81.63dB
0
TPC 1. AD7476 Dynamic Performance at 1 MSPS
FREQUENCY kHz
0
SNR dB
50
100
150
200
250
300
15
35
55
75
95
115
15
8192 POINT FFT
f
SAMPLE
= 600kSPS
f
IN
= 100kHz
SINAD = 71.71dB
THD = 80.88dB
SFDR = 83.23dB
TPC 2. AD7476 Dynamic Performance at 600 kSPS
FREQUENCY kHz
0
SNR dB
50
100
150
200
250
300
350
400
450
500
50
60
70
80
90
100
8192 POINT FFT
f
SAMPLE
= 1MSPS
f
IN
= 100kHz
SINAD = 61.66dB
THD = 80.64dB
SFDR = 85.75dB
40
30
20
10
0
TPC 3. AD7477 Dynamic Performance at 1 MSPS
FREQUENCY kHz
0
10
0
50
SNR dB
150
200
250
300
350
400
450
500
100
20
30
40
50
60
70
80
90
8192 POINT FFT
f
SAMPLE
= 1MSPS
f
IN
= 100kHz
SINAD = 49.82dB
THD = 75.22dB
SFDR = 67.78dB
TPC 4. AD7478 Dynamic Performance at 1 MSPS
INPUT FREQUENCY Hz
66
10k
SINAD dB
67
68
69
70
71
72
73
100k
1M
V
DD
= 2.35V
V
DD
= 2.7V
V
DD
= 5.25V
V
DD
= 4.75V
V
DD
= 3.6V
SCLK = 20MHz
TPC 5. AD7476 SINAD vs. Input Frequency at 993 kSPS
INPUT FREQUENCY Hz
69.0
10k
SINAD dB
69.5
70.0
70.5
71.0
71.5
72.0
72.5
100k
1M
V
DD
= 2.35V
V
DD
= 2.7V
V
DD
= 5.25V
V
DD
= 4.75V
V
DD
= 3.6V
SCLK = 12MHz
TPC 6. AD7476 SINAD vs. Input Frequency at 605 kSPS
REV. D
10
AD7476/AD7477/AD7478
CIRCUIT INFORMATION
The AD7476/AD7477/AD7478 are, respectively, 12-bit, 10-bit,
and 8-bit, fast, micropower, single-supply ADCs. The parts can be
operated from a 2.35 V to 5.25 V supply. When operated from
either a 5 V supply or a 3 V supply, the AD7476/AD7477/AD7478
are capable of throughput rates of 1 MSPS when provided with
a 20 MHz clock.
The AD7476/AD7477/AD7478 provide the user with an on-chip,
track-and-hold ADC, and a serial interface housed in a tiny
6-lead SOT-23 package, which offers the user considerable
space saving advantages over alternative solutions. The serial
clock input accesses data from the part and also provides the
clock source for the successive-approximation ADC. The analog
input range is 0 V to V
DD
. An external reference is not required
for the ADC, nor is there a reference on-chip. The reference for
the AD7476/AD7477/AD7478 is derived from the power supply
and thus gives the widest dynamic input range.
The AD7476/AD7477/AD7478 also feature a power-down option
to save power between conversions. The power-down feature is
implemented across the standard serial interface as described in
the Modes of Operation section.
CONVERTER OPERATION
The AD7476/AD7477/AD7478 are successive-approximation
analog-to-digital converters based around a charge redistribution
DAC. Figures 2 and 3 show simplified schematics of the ADC.
Figure 2 shows the ADC during its acquisition phase. SW2 is
closed and SW1 is in position A, the comparator is held in a
balanced condition, and the sampling capacitor acquires the
signal on V
IN
.
CHARGE
REDISTRIBUTION
DAC
SW2
V
DD
/2
SAMPLING
CAPACITOR
V
IN
SW1
A
B
AGND
ACQUISITION
PHASE
CONTROL
LOGIC
COMPARATOR
Figure 2. ADC Acquisition Phase
When the ADC starts a conversion (see Figure 3), SW2 will open
and SW1 will move to Position B, causing the comparator to
become unbalanced. The Control Logic and the Charge Redistri-
bution DAC are used to add and subtract fixed amounts of charge
from the sampling capacitor to bring the comparator back into a
balanced condition. When the comparator is rebalanced, the
conversion is complete. The Control Logic generates the ADC
output code. Figures 4 and 5 show the ADC transfer function.
CHARGE
REDISTRIBUTION
DAC
SW2
V
DD
/2
SAMPLING
CAPACITOR
V
IN
SW1
A
B
AGND
CONVERSION
PHASE
CONTROL
LOGIC
COMPARATOR
Figure 3. ADC Conversion Phase
ADC TRANSFER FUNCTION
The output coding of the AD7476/AD7477/AD7478 is straight
binary. For the AD7476/AD7477, designed code transitions
occur midway between successive integer LSB values (i.e.,
1/2 LSB, 3/2 LSB, and so on). The LSB size for the AD7476
is V
DD
/4096 and the LSB size for the AD7477 is V
DD
/1024. The
ideal transfer characteristic for the AD7476/AD7477 is shown
in Figure 4.
For the AD7478, designed code transitions occur midway between
successive integer LSB values (i.e., 1 LSB, 2 LSB, and so on).
The LSB size for the AD7478 is V
DD
/256. The ideal transfer
characteristic for the AD7478 is shown in Figure 5.
1LSB = V
DD
/4096 (AD7476)
1LSB = V
DD
/1024 (AD7477)
ANALOG INPUT
111 ... 111
0V
0.5LSB
ADC CODE
V
DD
1.5LSB
111 ... 110
111 ... 000
011 ... 111
000 ... 010
000 ... 001
000 ... 000
Figure 4. Transfer Characteristic for the AD7476/AD7477
ANALOG INPUT
111 ... 111
0V
1LSB
ADC CODE
V
DD
1LSB
111 ... 110
111 ... 000
011 ... 111
000 ... 010
000 ... 001
000 ... 000
1LSB = V
DD
/256 (AD7478)
Figure 5. Transfer Characteristic for AD7478
TYPICAL CONNECTION DIAGRAM
Figure 6 shows a typical connection diagram for the AD7476/
AD7477/AD7478. V
REF
is taken internally from V
DD
and as
such, V
DD
should be well decoupled. This provides an analog
input range of 0 V to V
DD
. The conversion result is output in a
16-bit word with four leading zeros followed by the MSB of the
12-bit, 10-bit, or 8-bit result. The 10-bit result from the AD7477
will be followed by two trailing zeros. The 8-bit result from
the AD7478 will be followed by four trailing zeros.
REV. D
AD7476/AD7477/AD7478
11
Alternatively, because the supply current required by the
AD7476/AD7477/AD7478 is so low, a precision reference can be
used as the supply source to the AD7476/AD7477/AD7478. A
REF19x voltage reference (REF195 for 5 V, or REF193 for 3 V)
can be used to supply the required voltage to the ADC (see
Figure 6). This configuration is especially useful if the power
supply is quite noisy or if the system supply voltages are at some
value other than 5 V or 3 V (e.g., 15 V). The REF19x will output
a steady voltage to the AD7476/AD7477/AD7478. If the low
dropout REF193 is used, the current it typically needs to supply
to the AD7476/AD7477/AD7478 is 1 mA. When the ADC is
converting at a rate of 1 MSPS, the REF193 will need to supply a
maximum of 1.6 mA to the AD7476/AD7477/AD7478. The load
regulation of the REF193 is typically 10 ppm/mA (REF193, V
S
=
5 V), which results in an error of 16 ppm (48
V) for the 1.6 mA
drawn from it. This corresponds to a 0.065 LSB error for the
AD7476 with V
DD
= 3 V from the REF193, a 0.016 LSB error for
the AD7477, and a 0.004 LSB error for the AD7478. For applica-
tions where power consumption is of concern, the Power-Down
mode of the ADC and the Sleep mode of the REF19x reference
should be used to improve power performance. See the Modes of
Operation section.
AD7476/
AD7477/
AD7478
V
DD
V
IN
GND
0V TO V
DD
INPUT
1 F
TANT
0.1 F
REF193
10 F
0.1 F
5V
SUPPLY
SCLK
SDATA
CS
SERIAL
INTERFACE
C/ P
3V
1mA
680nF
Figure 6. REF193 as Power Supply to AD7476/AD7477/
AD7478
Table I provides some typical performance data with various
references used as a V
DD
source with a low frequency analog
input. Under the same setup conditions, the references were
compared and the AD780 proved the optimum reference.
Table I.
Reference Tied
AD7476 SNR Performance
to V
DD
1 kHz Input (dB)
AD780 @ 3 V
71.17
REF193
70.4
AD780 @ 2.5 V
71.35
REF192
70.93
AD1582
70.05
Analog Input
Figure 7 shows an equivalent circuit of the analog input structure
of the AD7476/AD7477/AD7478. The two diodes D1 and D2
provide ESD protection for the analog inputs. Care must be
taken to ensure that the analog input signal never exceeds the
supply rails by more than 300 mV. This will cause these diodes
to become forward-biased and start conducting current into
the substrate. These diodes can conduct a maximum of 10 mA
without causing irreversible damage to the part. The capacitor
C1 in Figure 7 is typically about 4 pF and can primarily be
attributed to pin capacitance. The resistor R1 is a lumped
component made up of the on resistance of a switch. This
resistor is typically about 100
. The capacitor C2 is the ADC
sampling capacitor and typically has a capacitance of 30 pF. For
ac applications, removing high frequency components from the
analog input signal is recommended by use of a band-pass filter
on the relevant analog input pin. In applications where harmonic
distortion and signal-to-noise ratio are critical, the analog input
should be driven from a low impedance source. Large source
impedances will significantly affect the ac performance of the
ADC. This may necessitate the use of an input buffer amplifier.
The choice of the op amp will be a function of the particular
application.
V
DD
V
IN
C1
4pF
D2
D1
R1
C2
30pF
CONVERSION PHASE - SWITCH OPEN
TRACK PHASE - SWITCH CLOSED
Figure 7. Equivalent Analog Input Circuit
When no amplifier is used to drive the analog input, the source
impedance should be limited to low values. The maximum source
impedance will depend on the amount of total harmonic distortion
(THD) that can be tolerated. The THD will increase as the source
impedance increases and performance will degrade. Figure 8
shows a graph of the total harmonic distortion versus source
impedance for different analog input frequencies when using
a supply voltage of 2.7 V and sampling at a rate of 605 kSPS.
Figures 9 and 10 each show a graph of the total harmonic
distortion versus analog input signal frequency for various supply
voltages while sampling at 993 kSPS with an SCLK frequency of
20 MHz and 605 kSPS with an SCLK frequency of 12 MHz,
respectively.
SOURCE IMPEDANCE
0
10
THD dB
10
20
30
40
50
60
70
100
1k
80
90
100
V
DD
= 2.7V
f
S
= 605kSPS
f
IN
= 200kHz
f
IN
= 300kHz
f
IN
= 10kHz
f
IN
= 100kHz
1
10k
Figure 8. THD vs. Source Impedance for Various Analog
Input Frequencies
REV. D
12
AD7476/AD7477/AD7478
INPUT FREQUENCY Hz
50
10k
THD dB
55
60
65
70
75
100k
1M
80
85
90
V
DD
= 2.35V
V
DD
= 2.7V
V
DD
= 5.25V
V
DD
= 4.75V
V
DD
= 3.6V
Figure 9. THD vs. Analog Input Frequency, f
S
= 993 kSPS
INPUT FREQUENCY Hz
72
10k
THD dB
74
76
78
80
100k
1M
82
84
V
DD
= 2.35V
V
DD
= 2.7V
V
DD
= 5.25V
V
DD
= 4.75V
V
DD
= 3.6V
Figure 10. THD vs. Analog Input Frequency, f
S
= 605 kSPS
Digital Inputs
The digital inputs applied to the AD7476/AD7477/AD7478 are
not limited by the maximum ratings that limit the analog inputs.
Instead, the digital inputs applied can go to 7 V and are not
restricted by the V
DD
+ 0.3 V limit as on the analog inputs. For
example, if the AD7476/AD7477/AD7478 were operated with a
V
DD
of 3 V, then 5 V logic levels could be used on the digital
inputs. However, it is important to note that the data output on
SDATA will still have 3 V logic levels when V
DD
= 3 V. Another
advantage of SCLK and
CS not being restricted by the V
DD
+
0.3 V limit is the fact that power supply sequencing issues are
avoided. If
CS or SCLK is applied before V
DD
, there is no risk of
latch-up as there would be on the analog inputs if a signal greater
than 0.3 V was applied prior to V
DD
.
MODES OF OPERATION
The mode of operation of the AD7476/AD7477/AD7478 is
selected by controlling the (logic) state of the
CS signal during a
conversion. There are two possible modes of operation, Normal
mode and Power-Down mode. The point at which
CS is pulled
high after the conversion has been initiated will determine whether
or not the AD7476/AD7477/AD7478 will enter Power-Down
mode. Similarly, if already in power-down,
CS can control
whether the device will return to normal operation or remain in
power-down. These modes of operation are designed to provide
flexible power management options. These options can be chosen
to optimize the power dissipation/throughput rate ratio for different
application requirements.
Normal Mode
This mode is intended for fastest throughput rate performance,
as the user does not have to worry about any power-up times
with the AD7476/AD7477/AD7478 remaining fully powered all
the time. Figure 11 shows the general diagram of the operation
of the AD7476/AD7477/AD7478 in this mode.
The conversion is initiated on the falling edge of
CS as described
in the Serial Interface section. To ensure the part remains fully
powered up at all times,
CS must remain low until at least 10
SCLK falling edges have elapsed after the falling edge of
CS. If
CS is brought high any time after the tenth SCLK falling edge,
but before the sixteenth SCLK falling edge, the part will remain
powered up but the conversion will be terminated and SDATA
will go back into three-state. Sixteen serial clock cycles are
required to complete the conversion and access the complete
4 LEADING ZEROS + CONVERSION RESULT
CS
SCLK
SDATA
1
10
16
Figure 11. Normal Mode Operation
1
10
16
2
THREE-STATE
CS
SCLK
SDATA
Figure 12. Entering Power-Down Mode
REV. D
AD7476/AD7477/AD7478
13
conversion result.
CS may idle high until the next conversion or
may idle low until
CS returns high sometime prior to the next
conversion (effectively idling
CS low).
Once a data transfer is complete (SDATA has returned to three-
state), another conversion can be initiated after the quiet time,
t
QUIET
, has elapsed by again bringing
CS low.
Power-Down Mode
This mode is intended for use in applications where slower
throughput rates are required; either the ADC is powered down
between each conversion, or a series of conversions may be
performed at a high throughput rate and the ADC is then powered
down for a relatively long duration between these bursts of several
conversions. When the AD7476/AD7477/AD7478 is in power-
down, all analog circuitry is powered down.
To enter power-down, the conversion process must be interrupted
by bringing
CS high any time after the second falling edge of
SCLK and before the tenth falling edge of SCLK, as shown in
Figure 12. Once
CS has been brought high in this window of
SCLKs, the part will enter power-down and the conversion that
was initiated by the falling edge of
CS will be terminated and
SDATA will go back into three-state. If
CS is brought high before
the second SCLK falling edge, the part will remain in Normal mode
and will not power down. This will avoid accidental power-down
due to glitches on the
CS line.
To exit this mode of operation and power up the AD7476/
AD7477/AD7478 again, a dummy conversion is performed. On
the falling edge of
CS, the device will begin to power up, and
will continue to power up as long as
CS is held low until after the
falling edge of the tenth SCLK. The device will be fully powered
up once 16 SCLKs have elapsed and, as shown in Figure 13,
valid data will result from the next conversion. If
CS is brought
high before the tenth falling edge of SCLK, the AD7476/
AD7477/AD7478 will again go back into power-down. This
avoids accidental power-up due to glitches on the
CS line or an
inadvertent burst of eight SCLK cycles while
CS is low. So
although the device may begin to power up on the falling edge
of
CS, it will again power down on the rising edge of CS as long
as it occurs before the tenth SCLK falling edge.
Power-Up Time
The power-up time of the AD7476/AD7477/AD7478 is typically
1 s, which means that with any frequency of SCLK up to
20 MHz, one dummy cycle will always be sufficient to allow the
device to power up. Once the dummy cycle is complete, the ADC
will be fully powered up and the input signal will be acquired
properly. The quiet time (t
QUIET
) must still be allowed from the
point at which the bus goes back into three-state after the dummy
conversion, to the next falling edge of
CS. When running at
1 MSPS throughput rate, the AD7476/AD7477/AD7478 will
power up and acquire a signal within
0.5 LSB in one dummy
cycle, i.e., 1 s.
When powering up from the Power-Down mode with a dummy
cycle, as in Figure 13, the track-and-hold that was in Hold
mode while the part was powered down returns to Track mode
after the first SCLK edge the part receives after the falling edge of
CS. This is shown as Point A in Figure 13. Although at any
SCLK frequency one dummy cycle is sufficient to power up the
device and acquire V
IN
, it does not necessarily mean that a full
dummy cycle of 16 SCLKs must always elapse to power up the
device and fully acquire V
IN
; 1
s will be sufficient to power up the
device and acquire the input signal. If, for example, a 5 MHz
SCLK frequency were applied to the ADC, the cycle time would
be 3.2
s. In one dummy cycle, 3.2 s, the part would be powered
up and V
IN
fully acquired. However, after 1
s with a 5 MHz
SCLK, only five SCLK cycles would have elapsed. At this stage,
the ADC would be fully powered up and the signal acquired. So,
in this case, the
CS can be brought high after the tenth SCLK
falling edge and brought low again after a time t
QUIET
to initiate
the conversion.
When power supplies are first applied to the AD7476/AD7477/
AD7478, the ADC may power up in either Power-Down mode
or Normal mode. Because of this, it is best to allow a dummy
cycle to elapse to ensure the part is fully powered up before
attempting a valid conversion. Likewise, if it is intended to keep
the part in the Power-Down mode while not in use and the user
wants the part to power up in Power-Down mode, the dummy
cycle may be used to ensure the device is in power-down by
executing a cycle such as that shown in Figure 12. Once supplies
are applied to the AD7476/AD7477/AD7478, the power-up
time is the same as that when powering up from the Power-Down
mode. It takes approximately 1
s to fully power up if the part
powers up in Normal mode. It is not necessary to wait 1
s before
executing a dummy cycle to ensure the desired mode of operation.
Instead, the dummy cycle can occur directly after power is supplied
to the ADC. If the first valid conversion is then performed directly
after the dummy conversion, care must be taken to ensure that
adequate acquisition time has been allowed. As mentioned earlier,
when powering up from the Power-Down mode, the part will
return to track upon the first SCLK edge applied after the falling
edge of
CS. However, when the ADC powers up initially after
supplies are applied, the track-and-hold will already be in track.
This means that if the ADC powers up in the desired mode of
operation, and a dummy cycle is not required to change mode, then
a dummy cycle is not required to place the track-and-hold
into track.
1
10
16
16
1
A
CS
SCLK
SDATA
THE PART BEGINS
TO POWER UP
THE PART IS FULLY POWERED
UP WITH V
IN
FULLY ACQUIRED
INVALID DATA
VALID DATA
Figure 13. Exiting Power-Down Mode
REV. D
14
AD7476/AD7477/AD7478
POWER VS. THROUGHPUT RATE
By using the Power-Down mode on the AD7476/AD7477/AD7478
when not converting, the average power consumption of the ADC
decreases at lower throughput rates. Figure 14 shows how as the
throughput rate is reduced, the device remains in its power-down
state longer, and the average power consumption over time
drops accordingly.
For example, if the AD7476/AD7477/AD7478 is operated in a
continuous sampling mode with a throughput rate of 100 kSPS
and a SCLK of 20 MHz (V
DD
= 5 V), and the device is placed
in the Power-Down mode between conversions, then the power
consumption is calculated as follows. The power dissipation
during normal operation is 17.5 mW (V
DD
= 5 V). If the
power-up time is one dummy cycle, i.e., 1
s, and the remaining
conversion time is another cycle, i.e., 1
s, then the AD7476/
AD7477/AD7478 can be said to dissipate 17.5 mW for 2
s
during each conversion cycle. If the throughput rate is 100 kSPS,
the cycle time is 10
s and the average power dissipated
during each cycle is (2/10)
(17.5 mW) = 3.5 mW. If V
DD
=
3 V, SCLK = 20 MHz, and the device is again in Power-Down
mode between conversions, the power dissipation during normal
operation is 4.8 mW. The AD7476/AD7477/AD7478 can now
be said to dissipate 4.8 mW for 2
s during each conversion
cycle. With a throughput rate of 100 kSPS, the average power
dissipated during each cycle is (2/10)
(4.8 mW) = 0.96 mW.
Figure 14 shows the power versus throughput rate when using
the Power-Down mode between conversions with both 5 V
and 3 V supplies.
THROUGHPUT RATE kSPS
100
0
POWER mW
10
1
0.1
0.01
50
100
150
200
250
300
350
V
DD
= 5V, SCLK = 20MHz
V
DD
= 3V, SCLK = 20MHz
Figure 14. Power vs. Throughput Rate
The Power-Down mode is intended for use with throughput
rates of approximately 333 kSPS and under, because at higher
sampling rates power is not saved by using the Power-Down mode.
SERIAL INTERFACE
Figures 15, 16, and 17 show the detailed timing diagrams for
serial interfacing to the AD7476, AD7477, and AD7478,
respectively. The serial clock provides the conversion clock
and also controls the transfer of information from the AD7476/
AD7477/AD7478 during conversion.
The
CS signal initiates the data transfer and conversion process.
The falling edge of
CS puts the track-and-hold into Hold mode,
takes the bus out of three-state, and the analog input is sampled
at this point. The conversion is also initiated at this point and
will require sixteenth SCLK cycles to complete. Once 13 SCLK
falling edges have elapsed, the track-and-hold will go back into
track on the next SCLK rising edge as shown in Figures 15, 16,
and 17 at Point B. On the sixteenth SCLK falling edge, the
SDATA line will go back into three-state. If the rising edge of
CS occurs before 16 SCLKs have elapsed, the conversion will be
terminated and the SDATA line will go back into three-state;
otherwise, SDATA returns to three-state on the sixteenth SCLK
falling edge as shown in Figures 15, 16, and 17. Sixteen serial
clock cycles are required to perform the conversion process
and to access data from the AD7476/AD7477/AD7478.
CS
going low provides the first leading zero to be read in by the
microcontroller or DSP. The remaining data is then clocked out
by subsequent SCLK falling edges, beginning with the second
leading zero. Thus the first falling clock edge on the serial clock
has the first leading zero provided and also clocks out the second
leading zero. The final bit in the data transfer is valid on the
sixteenth falling edge, having been clocked out on the previous
(fifteenth) falling edge. In applications with a slower SCLK, it
is possible to read in data on each SCLK rising edge, i.e., al-
though the first leading zero will have to be read on the first
SCLK falling edge after the
CS falling edge. Therefore, the first
rising edge of SCLK after the
CS falling edge will provide the
second leading zero and the fifteenth rising SCLK edge will have
DB0 provided or the final zero for the AD7477 and AD7478.
This may not work with most microcontrollers/DSPs, but could
possibly be used with FPGAs and ASICs.
REV. D
AD7476/AD7477/AD7478
15
SCLK
CS
SDATA
t
2
t
3
t
4
t
7
t
6
t
5
t
8
t
QUIET
THREE-STATE
1
2
3
4
5
13
14
15
16
B
4 LEADING ZEROS
THREE-
STATE
ZERO
ZERO
ZERO
Z
DB11
DB10
DB2
DB1
DB0
t
CONVERT
t
1
Figure 15. AD7476 Serial Interface Timing Diagram
SCLK
CS
SDATA
t
2
t
3
t
4
t
7
t
6
t
5
t
8
t
QUIET
THREE-STATE
1
2
3
4
5
13
14
15
16
B
2 TRAILING
ZEROS
4 LEADING ZEROS
THREE-
STATE
ZERO
ZERO
ZERO
Z
DB9
DB8
DB0
ZERO
ZERO
t
CONVERT
t
1
Figure 16. AD7477 Serial Interface Timing Diagram
SCLK
CS
SDATA
t
2
t
3
t
4
t
7
t
6
t
5
t
8
t
QUIET
THREE-STATE
1
2
3
4
13
14
15
16
B
4 LEADING ZEROS
THREE-
STATE
ZERO
ZERO
ZERO
Z
DB7
ZERO
ZERO
t
CONVERT
8 BITS OF DATA
ZERO
ZERO
4 TRAILING ZEROS
12
t
1
Figure 17. AD7478 Serial Interface Timing Diagram
REV. D
16
AD7476/AD7477/AD7478
MICROPROCESSOR INTERFACING
The serial interface on the AD7476/AD7477/AD7478 allows
the part to be directly connected to a range of many different
microprocessors. This section explains how to interface the
AD7476/AD7477/AD7478 with some of the more common
microcontroller and DSP serial interface protocols.
AD7476/AD7477/AD7478 to TMS320C5x/C54x Interface
The serial interface on the TMS320C5x uses a continuous serial
clock and frame synchronization signals to synchronize the data
transfer operations with peripheral devices like the AD7476/
AD7477/AD7478. The
CS input allows easy interfacing between
the TMS320C5x/C54x and the AD7476/AD7477/AD7478 without
any glue logic required. The serial port of the TMS320C5x/C54x
is set up to operate in burst mode with internal CLKX (Tx serial
clock) and FSX (Tx frame sync). The serial port control register
(SPC) must have the following setup: FO = 0, FSM = 1,
MCM = 1, and TXM = 1. The format bit, FO, may be set to 1
to set the word length to eight bits, in order to implement the
Power-Down mode on the AD7476/AD7477/AD7478. The
connection diagram is shown in Figure 18. It should be noted that
for signal processing applications, it is imperative that the frame
synchronization signal from the TMS320C5x/C54x provides
equidistant sampling.
AD7476/
AD7477/
AD7478*
SCLK
SDATA
CS
TMS320C5x/
TMS320C54x*
CLKX
CLKR
DR
FSX
FSR
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 18. Interfacing to the TMS320C5x/C54x
AD7476/AD7477/AD7478 to ADSP-21xx Interface
The ADSP-21xx family of DSPs are interfaced directly to the
AD7476/AD7477/AD7478 without any glue logic required. The
SPORT control register should be set up as follows:
TFSW = RFSW = 1, Alternate Framing
INVRFS = INVTFS = 1, Active Low Frame Signal
DTYPE = 00, Right Justify Data
SLEN = 1111, 16-Bit Data-Words
ISCLK = 1, Internal Serial Clock
TFSR = RFSR = 1, Frame Every Word
IRFS = 0
ITFS = 1
To implement the Power-Down mode, SLEN should be set
to 0111 to issue an 8-bit SCLK burst. The connection diagram
is shown in Figure 19. The ADSP-21xx has the TFS and RFS of
the SPORT tied together, with TFS set as an output and RFS
set as an input. The DSP operates in Alternate Framing mode
and the SPORT control register is set up as described. The
frame synchronization signal generated on the TFS is tied to
CS and as with all signal processing applications, equidistant
sampling is necessary. However, in this example, the timer
interrupt is used to control the sampling rate of the ADC and, under
certain conditions, equidistant sampling may not be achieved.
The timer registers, for example, are loaded with a value that will
provide an interrupt at the required sample interval. When an
interrupt is received, a value is transmitted with TFS/DT (ADC
control word). The TFS is used to control the RFS and therefore
the reading of data. The frequency of the serial clock is set in the
SCLKDIV register. When the instruction to transmit with TFS
is given (i.e., TX0 = AX0), the state of the SCLK is checked.
The DSP will wait until the SCLK has gone high, low, and high
before transmission will start. If the timer and SCLK values are
chosen such that the instruction to transmit occurs on or near
the rising edge of SCLK, the data may be transmitted, or it may
wait until the next clock edge.
For example, the ADSP-2111 has a master clock frequency of
16 MHz. If the SCLKDIV register is loaded with the value 3,
a SCLK of 2 MHz is obtained, and eight master clock periods
will elapse for every one SCLK period. If the timer registers
are loaded with the value 803, 100.5 SCLKs will occur between
interrupts and subsequently between transmit instructions. This
situation will result in nonequidistant sampling as the transmit
instruction is occurring on an SCLK edge. If the number of
SCLKs between interrupts is a whole integer figure of N, equidis-
tant sampling will be implemented by the DSP.
SDATA
CS
DR
RFS
TFS
AD7476/
AD7477/
AD7478*
SCLK
ADSP-21xx*
SCLK
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 19. Interfacing to the ADSP-21xx
REV. D
AD7476/AD7477/AD7478
17
AD7476/AD7477/AD7478 to DSP56xxx Interface
The connection diagram in Figure 20 shows how the AD7476/
AD7477/AD7478 can be connected to the SSI (Synchronous
Serial Interface) of the DSP56xxx family of DSPs from Motorola.
The SSI is operated in Synchronous Mode (SYN bit in
CRB =1) with internally generated word frame sync for both
Tx and Rx (Bits FSL1 = 0 and FSL0 = 0 in CRB). Set the word
length to 16 by setting bits WL1 = 1 and WL0 = 0 in CRA. To
implement the Power-Down mode on the AD7476/AD7477/
AD7478, the word length can be changed to eight bits by setting
bits WL1 = 0 and WL0 = 0 in CRA. It should be noted that
for signal processing applications, it is imperative that the
frame synchronization signal from the DSP56xxx provides
equidistant sampling.
SDATA
CS
SRD
SC2
AD7476/
AD7477/
AD7478*
SCLK
DSP56xxx*
SCK
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 20. Interfacing to the DSP56xxx
AD7476/AD7477/AD7478 to MC68HC16 Interface
The Serial Peripheral Interface (SPI) on the MC68HC16 is
configured for Master Mode (MSTR = 1), the Clock Polarity
Bit (CPOL) = 1, and the Clock Phase Bit (CPHA) = 0. The SPI
is configured by writing to the SPI Control Register (SPCR)--see
the 68HC16 User Manual. The serial transfer will take place as
a 16-bit operation when the SIZE bit in the SPCR register is set
to SIZE = 1. To implement the Power-Down mode with an
8-bit transfer, set SIZE = 0. A connection diagram is shown
in Figure 21.
SDATA
CS
MISO/PMC0
SS/PMC3
AD7476/
AD7477/
AD7478*
SCLK
MC68HC16*
SCLK/PMC2
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 21. Interfacing to the MC68HC16
REV. D
18
AD7476/AD7477/AD7478
OUTLINE DIMENSIONS
6-Lead Plastic Surface-Mount Package [SOT-23]
(RT-6)
Dimensions shown in millimeters
1
3
4
5
2
6
2.90 BSC
PIN 1
1.60 BSC
2.80 BSC
1.90
BSC
0.95 BSC
0.22
0.08
0.60
0.45
0.30
10
0
0.50
0.30
0.15 MAX
1.30
1.15
0.90
SEATING
PLANE
1.45 MAX
COMPLIANT TO JEDEC STANDARDS MO-178AB
REV. D
AD7476/AD7477/AD7478
19
Revision History
Location
Page
3/04--Data Sheet changed from REV. C to REV. D.
Added U.S. Patent number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Changes to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Changes to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Changes to AD7476/AD7477/AD7478 to ADSP-21xx Interface section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2/03--Data Sheet changed from REV. B to REV. C.
Change to GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Changes to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Changes to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Change to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Change to TYPICAL CONNECTION DIAGRAM SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Change to Figure 8 caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Change to Figure 19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Change to Figure 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
OUTLINE DIMENSIONS updated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
C0102403/04(D)
20
PDF 
ZIP