1-174
H
Dome Packages
The HLMP-6XXX Series dome
lamps for use as indicators use
a tinted, diffused lens to provide
a wide viewing angle with a
high on-off contrast ratio. High
brightness lamps use an
untinted, nondiffused lens to
provide a high luminous
intensity within a narrow
radiation pattern.
Arrays
The HLMP-66XX Series
subminiature lamp arrays are
available in lengths of 3 to 8
elements per array. The
luminous intensity is matched
within an array to assure a 2.1
to 1.0 ratio.
Resistor Lamps
The HLMP-6XXX Series 5 volt
subminiature lamps with built
in current limiting resistors are
for use in applications where
space is at a premium.
Lead Configurations
All of these devices are made by
encapsulating LED chips on
axial lead frames to form molded
epoxy subminiature lamp
packages. A variety of package
configuration options is avail-
able. These include special
Features
Subminiature Flat Top
Package
Ideal for Backlighting and
Light Piping Applications
Subminiature Dome
Package
Diffused Dome for Wide
Viewing Angle
Nondiffused Dome for High
Brightness
Arrays
TTL and LSTTL
Compatible 5 Volt Resistor
Lamps
Available in Six Colors
Ideal for Space Limited
Applications
Axial Leads
Available with Lead
Configurations for Surface
Mount and Through Hole
PC Board Mounting
Description
Flat Top Package
The HLMP-PXXX Series flat top
lamps use an untinted, non-
diffused, truncated lens to
provide a wide radiation pattern
that is necessary for use in
backlighting applications. The
flat top lamps are also ideal for
use as emitters in light pipe
applications.
Subminiature LED Lamps
Technical Data
surface mount lead configura-
tions, gull wing, yoke lead or Z-
bend. Right angle lead bends at
2.54 mm (0.100 inch) and
5.08 mm (0.200 inch) center
spacing are available for
through hole mounting. For
more information refer to
Standard SMT and Through
Hole Lead Bend Options for
Subminiature LED Lamps data
sheet.
HLMP-PXXX Series
HLMP-QXXX Series
HLMP-6XXX Series
HLMP-70XX Series
5964-9350E
1-175
DH AS
High
High
Device
Standard
AlGaAs Efficiency
Perf.
Emerald
Outline
Red
Red
Red
Orange Yellow
Green
Green
Device Description
[1]
Drawing
P105
P205
P405
P305
P505
P605
Untinted, Nondiffused,
A
Flat Top
P102
P202
P402
P302
P502
Untinted, Diffused,
B
Flat Top
6000/6001
Q101
6300
Q400
6400
6500
Q600
Tinted, Diffused
Q105
6305
6405
6505
Untinted, Nondiffused,
High Brightness
Q150
7000
7019
7040
Tinted, Diffused, Low
B
Current
Q155
Nondiffused, Low
Current
6600
6700
6800
Tinted, Diffused,
Resistor, 5 V, 10 mA
6620
6720
6820
Diffused, Resistor, 5 V,
4 mA
6203
6653
6753
6853
3 Element
Matched
6204
6654
6754
6854
4 Element
6205
6655
6755
6855
5 Element
C
6206
6656
6756
6856
6 Element
6208
6658
6758
6858
8 Element
Device Selection Guide
Part Number: HLMP-XXXX
Package Dimensions
(A) Flat Top Lamps
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).
2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.
*Refer to Figure 1 for design concerns.
Array,
Tinted,
Diffused
1-176
Package Dimensions (cont.)
(B) Diffused and Nondiffused
Figure 1. Proper Right Angle Mounting to a PC Board to Prevent Protruding Cathode Tab from Shorting to Anode
Connection.
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).
2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.
*Refer to Figure 1 for design concerns.
(C) Arrays
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).
2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.
1-177
DH AS
High
High
Standard
AlGaAs
Eff.
Perf.
Emerald
Parameter
Red
Red
Red
Orange
Yellow
Green
Green
Units
DC Forward Current
[1]
50
30
30
30
20
30
30
mA
Peak Forward Current
[2]
1000
300
90
90
60
90
90
mA
DC Forward Voltage
6
6
6
6
V
(Resistor Lamps Only)
Reverse Voltage (I
R
= 100
A)
5
5
5
5
5
5
5
V
Transient Forward Current
[3]
2000
500
500
500
500
500
500
mA
(10
s Pulse)
Operating Temperature Range:
-55 to
-40 to
-55 to +100
-40 to
-20 to
Non-Resistor Lamps
+100
+100
+100
+100
C
Resistor Lamps
-40 to +85
-20 to
+85
Storage Temperature Range
C
For Thru Hole Devices
260
C for 5 Seconds
Wave Soldering Temperature
[1.6 mm (0.063 in.) from body]
For Surface Mount Devices:
Convective IR
235
C for 90 Seconds
Vapor Phase
215
C for 3 Minutes
Absolute Maximum Ratings at T
A
= 25
C
-55 to +100
Notes:
1. See Figure 5 for current derating vs. ambient temperature. Derating is not applicable to resistor lamps.
2. Refer to Figure 6 showing Max. Tolerable Peak Current vs. Pulse Duration to establish pulsed operating conditions.
3. The transient peak current is the maximum non-recurring peak current the device can withstand without failure. Do not
operate these lamps at this high current.
PDF 
ZIP