Dome Packages
The HLMP-6xxx Series dome
lamps for use as indicators use a
tinted, diffused lens to provide a
wide viewing angle with a high
on-off contrast ratio. High
brightness lamps use an untinted,
nondiffused lens to provide a
high luminous intensity within a
narrow radiation pattern.
Resistor Lamps
The HLMP-6xxx Series 5 volt
subminiature lamps with built in
current limiting resistors are for
use in applications where space is
at a premium.
Lead Configurations
All of these devices are made by
encapsulating LED chips on axial
lead frames to form molded epoxy
subminiature lamp packages. A
variety of package configuration
options is available. These
Features
Subminiature Flat Top
Package
Ideal for Backlighting and
Light Piping Applications
Subminiature Dome Package
Diffused Dome for Wide
Viewing Angle
Nondiffused Dome for High
Brightness
TTL and LSTTL Compatible
5 Volt Resistor Lamps
Available in Six Colors
Ideal for Space Limited
Applications
Axial Leads
Available with Lead
Configurations for Surface
Mount and Through Hole PC
Board Mounting
Description
Flat Top Package
The HLMP-Pxxx Series flat top
lamps use an untinted, non-
diffused, truncated lens to
provide a wide radiation
pattern that is necessary for
use in backlighting
applications. The flat top lamps
are also ideal for use as
emitters in light pipe
applications.
Subminiature LED Lamps
Technical Data
HLMP-Pxxx Series
HLMP-Qxxx Series
HLMP-6xxx Series
HLMP-70xx Series
include special surface mount
lead configurations, gull wing,
yoke lead or Z-bend. Right angle
lead bends at 2.54 mm (0.100
inch) and 5.08 mm (0.200 inch)
center spacing are available for
through hole mounting. For more
information refer to Standard
SMT and Through Hole Lead
Bend Options for Subminiature
LED Lamps data sheet.
3
(B) Diffused and Nondiffused
Figure 1. Proper Right Angle Mounting to a PC Board to Prevent Protruding Cathode Tab from
Shorting to Anode Connection.
Package Dimensions
(A) Flat Top Lamps
NO. ANODE DOWN.
YES. CATHODE DOWN.
CATHODE
TAB
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETRES (INCHES).
2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.
3. LEAD POLARITY FOR AlGaAs LAMPS IS OPPOSITE TO THE LEAD
POLARITY OF SUBMINIATURE LAMPS USING OTHER TECHNOLOGIES.
0.50 (0.020) REF.
0.94
1.24
(0.037)
(0.049)
2.92 (0.115)
MAX.
0.76
0.89
(0.030)
(0.035)
R.
0.63
0.38
(0.025)
(0.015)
2.03 (0.080)
1.78 (0.070)
0.79 (0.031)
0.53 (0.021)
0.46
0.56
(0.018)
(0.022)
0.25 (0.010) MAX.
NOTE 2
0.20 (0.008) MAX.
CATHODE
1.65
1.91
(0.065)
(0.075)
DIA.
ANODE
11.68
10.67
(0.460)
(0.420)
BOTH SIDES
0.18
0.23
(0.007)
(0.009)
2.08
2.34
(0.082)
(0.092)
CATHODE
STRIPE
2.21
1.96
(0.087)
(0.077)
0.46
0.56
(0.018)
(0.022)
1.40
1.65
(0.055)
(0.065)
0.25 (0.010) MAX.
NOTE 2
0.20 (0.008) MAX.
0.50 (0.020) REF.
CATHODE
1.65
1.91
(0.065)
(0.075)
DIA.
ANODE
11.68
10.67
(0.460)
(0.420)
BOTH SIDES
1.14
1.40
(0.045)
(0.055)
0.63
0.38
(0.025)
(0.015)
2.21
1.96
(0.087)
(0.077)
0.18
0.23
(0.007)
(0.009)
0.79 (0.031) MAX.
2.44
1.88
(0.096)
(0.074)
2.08
2.34
(0.082)
(0.092)
CATHODE
STRIPE
4
DH AS
High
High
Standard AlGaAs
Eff.
Perf.
Emerald
Parameter
Red
Red
Red
Orange
Yellow
Green
Green
Units
DC Forward Current
[1]
50
30
30
30
20
30
30
mA
Peak Forward Current
[2]
1000
300
90
90
60
90
90
mA
DC Forward Voltage
6
6
6
6
V
(Resistor Lamps Only)
Reverse Voltage (I
R
= 100
A)
5
5
5
5
5
5
5
V
Transient Forward Current
[3]
2000
500
500
500
500
500
500
mA
(10
s Pulse)
Operating Temperature Range:
-55 to
-40 to
-55 to +100
-40 to
-20 to
Non-Resistor Lamps
+100
+100
+100
+100
C
Resistor Lamps
-40 to +85
-20 to
+85
Storage Temperature Range
C
For Thru Hole Devices
260
C for 5 Seconds
Wave Soldering Temperature
[1.6 mm (0.063 in.) from body]
For Surface Mount Devices:
Convective IR
235
C for 90 Seconds
Vapor Phase
215
C for 3 Minutes
Absolute Maximum Ratings at T
A
= 25
C
-55 to +100
Notes:
1. See Figure 5 for current derating vs. ambient temperature. Derating is not applicable to resistor lamps.
2. Refer to Figure 6 showing Max. Tolerable Peak Current vs. Pulse Duration to establish pulsed operating conditions.
3. The transient peak current is the maximum non-recurring peak current the device can withstand without failure. Do not
operate these lamps at this high current.
5
Electrical/Optical Characteristics, T
A
= 25
C
Standard Red
Device
HLMP-
Parameter
Symbol Min.
Typ. Max.
Units
Test Conditions
6000-E00xx Luminous Intensity
[1]
I
V
0.63
1.2
mcd
I
F
= 10 mA
6000-G00xx
1.60
3.2
P005-F00xx
1.0
2.5
Forward Voltage
V
F
1.4
1.6
2.0
V
I
F
= 10 mA
All
Reverse Breakdown
V
R
5.0
12.0
V
I
R
= 100
A
Voltage
6000
Included Angle Between
2
1
/
2
90
Deg.
Half Intensity Points
[2]
P005
125
Peak Wavelength
PEAK
655
nm
Dominant Wavelength
[3]
d
640
nm
Spectral Line Half Width
1/2
24
nm
All
Speed of Response
s
15
ns
Capacitance
C
100
pF
V
F
= 0; f = 1 MHz
Thermal Resistance
R
J-PIN
170
C/W
Junction-to-Cathode
Lead
Luminous Efficacy
[4]
v
65
lm/W
PDF 
ZIP