1-454
200-V/160 Ohm, 1 Form A,
Small-Signal Solid State Relay
Technical Data
HSSR-8200
Features
Compact Solid-State
Bidirectional Signal Switch
Normally-Off Single-Pole
Relay Function (1 Form A)
Very High Output Off-
Impedance: 10,000
Gigaohms Typical at 25
C
Very Low Output Offset
Voltage: < 0.5
V at
I
F
= 1 mA
200-Volt Output Withstand
Voltage at 25
C
High-Transient Immunity:
> 2000 V/
s
Monolithic High-Voltage IC
Operating Range: -40
C to
+85
C
Very Low Input Current
(1 mA); CMOS Compatibility
High-Speed Switching: 50
s
Typical
160-Ohm Maximum On-
Resistance at 25
C
Surface Mount Option
8-kV ESD Immunity: MIL-
STD-883 Method 3015
Input-to-Output Insulation
Voltage: 2500 Vac, 1 Minute
UL 508 Recognized
CSA Approved
Applications
Relay Scanners & Analog
Input Modules of Data
Acquisition Systems
Analog Input Modules of
Programmable Logic
Controllers
Relay Multiplexers of High-
Performance Voltmeters
Telecommunication Test
Instruments
Functional Tester of Board
Test Equipment
Analog Signal Multiplexer
Flying Capacitor Multiplexer
Reed Relay Replacement
Description
The HSSR-8200 consists of a high-
voltage integrated circuit optically
coupled with a light emitting diode.
This device is a solid-state
replacement for single-pole,
normally-open electromechanical
relays used for general purpose
switching of analog signals.
The light-emitting diode controls
the ON/OFF function of the solid-
state relay. The detector contains
high voltage MOS transistors and a
high speed photosensitive drive
circuit. This relay has superior OFF
impedance, very low output offset
voltage and input drive current.
H
Functional Diagram
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to
prevent damage and/or degradation which may be induced by ESD.
TRUTH TABLE
(POSITIVE LOGIC)
LED
ON
OFF
OUTPUT
L
H
5965-3574E
1-455
The electrical and switching
characteristics of the HSSR-8200
are specified from 40
C to
+85
C. The low I
F
allows
compatibility with TTL, LSTTL,
and CMOS logic resulting in low
power consumption compared to
other solid state and mechanical
relays.
Ordering Information
Specify part number followed by Option Number (if desired).
HSSR-8200#XXX
300 = Gull Wing Surface Mount Lead Option
500 = Tape/Reel Package Option (1 K min)
Option data sheets available. Contact your Hewlett-Packard sales representative or authorized distributor for
information.
Selection Guide
Maximum
Maximum
Maximum
6-Pin DIP
4-Pin DIP
Maximum
ON
Output
Output
Hermetic
(300 Mil)
(300 Mil)
Speed
Resistance
Voltage
Current
Minimum
8-Pin
Single
Dual
t(ON)
R(ON)
VO(off)
Io(ON)
Input
Single
Channel
Channel
msec
V
mA
Current
Channel
Package
Package
25
C
25
C
25
C
25
C
mA
Packages
HSSR-8400
[1]
0.95
10
400
150
5
HSSR-8060
[1]
1.4
0.7
60
750
5
HSSR-8200
1.5
200
200
40
1
6
1
90
800
5
HSSR-7110
[1]
Note:
1. Technical data are on separate HP publication.
Schematic
IF
VF
1
4
+
8
SWITCH
DRIVER
5
1-456
Package Outline Drawings
4-Pin DIP Package (HSSR-8200)
9.40 (0.370)
9.90 (0.390)
PIN
ONE
HP RXXXX
YYWW
TYPE
NUMBER
DATE CODE
0.76 (0.030)
1.40 (0.055)
0.51 (0.020) MIN.
4.70 (0.185) MAX.
2.92 (0.115) MIN.
6.10 (0.240)
6.60 (0.260)
0.02 (0.008)
0.33 (0.013)
5 TYP.
7.37 (0.290)
7.87 (0.310)
DIMENSIONS IN MILLIMETERS
AND (INCHES).
1.19 (0.047) MAX.
5
8
4
1
7.37 (0.290)
7.87 (0.310)
0.65 (0.025) MAX.
4-Pin DIP Package with Gull Wing Surface Mount Option 300
0.635 0.25
(0.025 0.010)
12 NOM.
0.20 (0.008)
0.33 (0.013)
9.65 0.25
(0.380 0.010)
0.50 0.130
(0.020 0.005)
7.62 0.25
(0.300 0.010)
5
8
4
1
9.65 0.25
(0.380 0.010)
PIN 1
1.080 0.320
(0.043 0.013)
4.19
(0.165)
MAX.
1.19
(0.047)
MAX.
7.62 0.25
(0.300 0.010)
DIMENSIONS IN MILLIMETERS (INCHES).
6.35 0.25
(0.250 0.010)
1-457
240
T = 115C, 0.3C/SEC
0
T = 100C, 1.5C/SEC
T = 145C, 1C/SEC
TIME MINUTES
TEMPERATURE C
220
200
180
160
140
120
100
80
60
40
20
0
260
1
2
3
4
5
6
7
8
9
10
11
12
Thermal Profile (Option #300)
Figure 1. Maximum Solder Reflow Thermal Profile.
(Note: Use of non-chlorine activated fluxes is recommended.)
Regulatory Information
The HSSR-8200 has been
approved by the following
organizations:
UL
Recognized under UL 508,
Component Recognition
Program, Industrial Control
Switches, File E142465.
CSA
Approved under CAN/CSA-C22.2
No. 14-95, Industrial Control
Equipment, File LR 87683.
Insulation and Safety Related Specifications
Parameter
Symbol
Value
Units
Conditions
Min. External Air Gap
L(IO1)
7.0
mm
Measured from input terminals to output
(External Clearance)
terminals, shortest distance through air
Min. External Tracking Path
L(IO2)
7.5
mm
Measured from input terminals to output
(External Creepage)
terminals, shortest distance path along body
Min. Internal Plastic Gap
0.5
mm
Through insulation distance, conductor to
(Internal Clearance)
conductor, usually the direct distance
between the photoemitter and photodetector
inside the optocoupler cavity
Tracking Resistance
CTI
200
Volts
DIN IEC 112/VDE 0303 PART 1
(Comparative Tracking Index)
Isolation Group
IIIa
Material Group (DIN VDE 0110, 1/89, Table 1)
Option 300 surface mount classification is Class A in accordance with CECC 00802.
1-458
Absolute Maximum Ratings
Storage Temperature ................................................... -55
C to+125
C
Operating Temperature ................................................. -40
C to +85
C
Lead Solder Temperature .... 260
C for 10 s (1.6 mm below seating plane)
Average Input Current - I
F
............................................................ 10 mA
Repetitive Peak Input Current - I
F
.................... 20 mA; 50% Duty Cycle
Transient Peak Input Current - I
F
............................................... 100 mA
(
1
s pulse width; 1 kHz Pulse Repetition Rate)
Reverse Input Voltage ....................................................................... 5 V
Average Output Current I
O
................................................... 40 mA
[1]
Input Output Insulation Voltage ......................................... 2500 VAC
[6]
Output Power Dissipation ..................................................... 320 mW
[2]
Output Voltage V
O
..................................................... -200 V to 200 V
Infrared and Vapor Phase Reflow Temperature
(Option #300) .......................................... see Fig. 1, Thermal Profile
Recommended Operating Conditions
Parameter
Symbol
Min.
Max.
Units
Input Current (ON)
I
F(ON)
1
5
mA
Input Voltage (OFF)
V
F(OFF)
0
0.6
Volt
Operating Temperature
T
A
-40
+85
C
Output Voltage
V
O(OFF)
-200
200
Volt
Output Current
I
O(ON)
-40
40
mA
PDF 
ZIP