Data
sheet
www.bookham.com
Thinking optical solutions
www.bookham.com
Thinking optical solutions
Features
2.5 Gb/s operation
Narrow spectral line-width
Internal TEC with precision NTC
thermistor for temperature control
Code reduction with single
product for reaches up to 175 km
GaInAsP SLMQW DFB single
frequency laser chip
InGaAs monitor photo-diode
Hermetically sealed 14-pin
butterfly package with
optical isolator
Applications
TDM
On-off ramps
Long-Haul
2.5 Gb/s Buried Het Laser
175 km Reach non-WDM
applications
This laser module employs the Bookham Technology
strained layer MQW Buried Heterostructure DFB laser chip,
and has been designed specifically for use in 2.5 Gb/s long
distance single channel optical fibre systems. The device is
packaged in a hermetically sealed 14-pin butterfly package
incorporating an isolator and monitor photodiode
for control of the power of the laser over life and all
operating conditions.
Parameter
Min
Max
Unit
Case operating temperature
0
70
C
Laser submount operating temperature
20
35
C
Storage temperature
-40
85
C
Laser current above Ith
100
mA
Laser reverse voltage
1.0
V
Laser reverse current
10
A
Monitor diode bias
-10
V
Heatpump voltage
2.4
V
Fibre bend radius
30
mm
Parameter
Conditions
Min
Typ
Max
Unit
Threshold current (Ith)
10
22
mA
Slope efficiency by product
2 mW
0.04
0.09
mW/mA
3 mW
0.06
0.13
4 mW
0.08
0.17
10 mW
0.143
0.43
RF input reflection coef (S11)
(1)
-10
dB
Forward voltage
1.3
1.8
V
Peak wavelength (
p)
(2)
1535.82
1560.61
nm
Dispersion penalty at 175 km
(3)
2
dB
Time averaged spectral linewidth
-20 dB
0.1
0.6
nm
Side-mode suppression
32
40
dB
Optical rise/fall time
(4)
125
ps
Monitor photo current
50
250
1200
A
Monitor dark current
100
nA
Thermistor resistance
10
k
Heatpump current
70C case temperature
250
600
900
mA
Heatpump voltage
70C case temperature
1.0
2.4
V
Change of
p with laser temp.
20 to 35
0.09
nm/C
Parameters
(1)
50
measurement system, f = dc - 3 GHz
(2)
Submount temperature between 20C & 35C start of life to achieve required
p
(3)
Standard product dispersion penalty will be compliant to the specified link length of
175 km using an extinction ratio of 10 dB. Fibre dispersion characteristics are derived from
the following equation
Where So = 0.092 ps/(nm
2
.km) and
= 1302 nm
(4)
Measurements determined from 20 - 80% pk - pk
)
.
/(
)
(
4
)
(
3
4
0
km
nm
ps
So
D
-
=
Absolute Maximum Ratings
www.bookham.com
Thinking optical solutions
www.bookham.com
Thinking optical solutions
Outline Drawing
Dimensions in mm
PIN 1
1.52
30
26.040.08
20.83
14 PINS x 0.50.08
8.9
12.7
12.7
MIN
2.79
ON 2.54 PITCH
17.8
10.5
5
9.92
4.12
4 HOLES 2.6
36 MAX
NOSE CONE BOOT
HYTREL SECONDARY COATED
DIMENSIONS IN MILLIMETRES
TOLERANCES UNLESS
OTHERWISE SPECIFIED:
X.XX = 0.25
X.XXX = 0.127
MAX
5.46
Figure 1: Outline Drawing
Reliability/Quality
Meets Qualification requirements of Telcordia / Bellcore GR468-Core for central office environment.
Operating reliability <500 FITs1 in 15 years.
1- Assumes laser die submount held at <35C by internal thermoelectric cooler, mean forward current of 35 mA,
and end of life limits based on 10 mA increase in Ith and 25% change in laser efficiency. FIT rate data for other end
of life criteria, including minimum extinction ratio requirements, are available upon request.
Instructions for Use LC25WZ*A
Pin 1 and Pin 2 Thermistor
The thermistor is used in a control loop in conjunction with the thermo-electric cooler to maintain the laser submount
temperature at the required value for wavelength. Operating current should be less than 100 A to prevent self-heating errors.
Pin 3 Laser DC bias (-)
Laser bias current (negative with respect to package ground) is applied via this pin which forms one side of the bias-T
connection to the laser cathode.
Pin 4 Monitor anodes, Pin 5 Common Monitor cathode
The back facet monitor provides a mean power reference for the laser and is normally operated with a 5 V reverse bias.
www.bookham.com
Thinking optical solutions
www.bookham.com
Thinking optical solutions
Pin 6 TEC (+), Pin 7 TEC (-)
Applying a positive voltage on pin 6 with respect to pin 7 will cause the internal submount to be cooled relative to the case
temperature. Reversing the polarity will raise the submount temperature relative to the case. The TEC supply should be
capable of delivering up to 0.9 A at 2.4 V.
Pin 8, 9, 11, 13 Case ground
These pins must be grounded in all applications
Pin 10
This pin is not connected and should be grounded if possible
Pin 12 Laser modulation (-)
The data input (modulation current) is applied via this pin which is a nominal 25 Ohm impedance coplanar line. For 10mW
applications the end of life modulation current is 90mA maximum. For all other applications 60mA maximum modulation
current should be provisioned.
Pin 14 N/C
This pin is not connected. It should be grounded if possible.
Pin Function
1
Thermistor
2
Thermistor
3
Laser DC bias (-)
4
Monitor Anode (-)
5
Monitor Cathode (+)
6
TEC (+)
7
TEC (-)
8
Case Ground
9
Case Ground
10
Not Connected
11
Case Ground
12
Laser Modulation (-)
13
Case Ground
14
Not Connected
Connections
www.bookham.com
Thinking optical solutions
www.bookham.com
Thinking optical solutions
Safety Information
Laser safety classifications:
IEC 60825-1: Edition 1.2 Class 1M
21 CFR Ch.1 (4-1-97 Edition) Class IIIb
Electrostatic discharge:
ESD threshold >500 V
A-TSY-000870 class 3.
Ordering Information
LC25WZ
[Power Option]
A
[Connector]
E= 2 mW pk
-
C28= SC/PC
C= 3 mW pk
-
C34= FC/PC
A= 4 mW pk
-
C57= LC
B= 10 mW pk
-
C59= MU
Fibre length 1130 to 1190 mm
E.g. LC25WZCA-C28 is a 3mW device with an SC connector
THIS PRODUCT COMPLIES WITH 21 CFR 1040.10
INVISIBLE LASER RADIATION
DO NOT VIEW DIRECTLY
WITH OPTICAL INSTRUMENTS
CLASS 1M LASER
DANGER
INVISIBLE LASER RADIATION
AVOID DIRECT
EXPOSURE TO BEAM
OUTPUT POWER 21 mW
WAVELENGTH >1510 nm
CLASS IIIb LASER PRODUCT
CAUTION
STATIC SENSITIVE DEVICE
OBSERVE PRECAUTIONS
Certificate No. FM 15040
Certificate No. EMS 35100
REFERENCE IEC 60825-1: Edition 1.2
www.bookham.com
REV 1 Feb 2003
Bookham Technology 2003 Bookham & ASOC are registered trademarks of Bookham Technology plc
North America
Bookham Technology Inc.
49 Buford Highway
Suwanee
GA 30024
USA
Tel: +1 678 482 4021
Fax: +1 678 482 4022
Europe
Bookham Technology plc
Brixham Road
Paignton
Devon
TQ4 7BE
UK
Tel: +44 (0) 1803 66 2875
Fax: +44 (0) 1803 66 2801
Asia
Bookham Technology plc
21/F Cityplaza One
1111 King's Road
Quarry Bay
Hong Kong
Tel: +852 (2100) 2249
Fax: +852 (2100) 2585
Sales@bookham.com
Important Notice
Bookham Technology has a policy of
continuous improvement, as a result
certain parameters detailed on this flyer
may be subject to change without notice.
If you are interested in a particular product
please request the available from any
Bookham Technology sales representative.
PDF 
ZIP