High Voltage, High Current
OPERATIONAL AMPLIFIER
APPLICATIONS
q
PROGRAMMABLE POWER SUPPLY
q
PIEZO-ELECTRIC TRANSDUCER DRIVER
q
HIGH VOLTAGE CURRENT SOURCE
FEATURES
q
WIDE POWER SUPPLY VOLTAGE:
70V to
150V
q
OUTPUT CURRENT TO 75mA
q
SLEW RATE: 30V/
s
q
FET INPUT: I
B
= 20pA max
q
THERMAL SHUT-DOWN PROTECTION
q
HERMETIC TO-3 PACKAGE, ISOLATED
CASE
DESCRIPTION
The 3583 is a high voltage, high speed hybrid opera-
tional amplifier designed for a wide variety of
programmable power supply and transducer driver
applications.
The 3583 operates over a wide power supply range
(
50V to
150V) and provides outputs up to 75mA.
Laser-trimmed FET input circuitry provides low offset
voltage (3mV max) and low input bias current (20pA
max). Thermal shut-down circuitry protects internal
circuitry from excessive power dissipation.
Commercial and industrial temperature range models
are available. The 3583's hermetic 8-pin TO-3 pack-
age is electrically isolated from all internal circuitry.
3
Output
1
Offset Trim
2
V+
5
In
6
+In
7
V
4
3583
International Airport Industrial Park Mailing Address: PO Box 11400 Tucson, AZ 85734 Street Address: 6730 S. Tucson Blvd. Tucson, AZ 85706
Tel: (520) 746-1111 Twx: 910-952-1111 Cable: BBRCORP Telex: 066-6491 FAX: (520) 889-1510 Immediate Product Info: (800) 548-6132
1976 Burr-Brown Corporation
PDS-343D
Printed in U.S.A October, 1993
SBOS130
2
3583
3583AM
3583JM
PARAMETER
CONDITIONS
MIN
TYP
MAX
MIN
TYP
MAX
UNITS
OFFSET VOLTAGE
Input Offset Voltage
3
*
mV
vs Temperature
Specified Temp. Range
23
*
V/
C
vs Power Supply
20
*
V/V
vs Time
50
V/month
INPUT BIAS CURRENT
(1)
Input Bias Current
V
CM
= 0V
20
*
pA
vs Temperature
Doubles Every 10
C
*
vs Power Supply
0.2
*
pA/V
Input Offset Current
V
CM
= 0V
20
*
pA
vs Temperature
Doubles Every 10
C
*
vs Power Supply
0.2
*
pA/V
NOISE
Voltage, 0.01Hz to 10Hz
5
*
Vp-p
10Hz to 1kHz
1.7
*
Vrms
Current, 0.01Hz to 10Hz
0.3
*
pAp-p
INPUT VOLTAGE RANGE
Max Safe Differential Input
(V+) + |V|
*
Max Safe Common-Mode Input
V to V+
*
Common-Mode Input Range
Linear Operation
V
S
10
*
V
Common-Mode Rejection
110
*
dB
INPUT IMPEDANCE
Differential
10
11
|| 10
*
|| pF
Common-Mode
10
11
*
|| pF
OPEN-LOOP GAIN
Open-Loop Voltage Gain
No Load, DC
118
*
dB
Open-Loop Voltage Gain
Rated Load, DC
94
105
*
*
dB
FREQUENCY RESPONSE
Unity-Gain Bandwidth
Small-Signal
5
*
MHz
Full-Power Bandwidth
R
L
= 10k
60
*
kHz
Slew Rate
30
*
V/
s
Settling Time: 0.1%
12
*
s
OUTPUT
Voltage Output
V
S
10
*
V
Current Output
75
*
mA
Short Circuit Current
100
*
mA
Load Capacitance
10
*
nF
POWER SUPPLY
Operating Voltage Range
50
150
*
*
V
Quiescent Current
I
O
= 0
8.5
*
mA
TEMPERATURE RANGE (CASE)
Specification
25
+85
0
+70
C
Operating
55
+125
*
*
C
Storage
JC
= 4
C/W
55
+125
*
*
C
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN
assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user's own risk. Prices and specifications are subject
to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not
authorize or warrant any BURR-BROWN product for use in life support devices and/or systems.
SPECIFICATIONS
ELECTRICAL
T
CASE
= +25
C, V
S
=
150V, unless otherwise noted.
* Specification same as 3583AM.
NOTE: (1) Inputs may be damaged by input slew rates exceeding 1000V/
s. Inputs can be protected from signals exceeding 1000V/
s by limiting input current to 150mA
with external series resistors (pins 5 and 6).
3
3583
CONNECTION DIAGRAM
TYPICAL PERFORMANCE CURVES
T
CASE
= +25
C,
V
CC
= 150VDC, unless otherwise noted.
Top View
TO-3
PACKAGING INFORMATION
PACKAGE DRAWING
MODEL
PACKAGE
NUMBER
(1)
3583AM
8-Pin TO 3
030
3583JM
8-Pin TO 3
030
NOTE: (1) For detailed drawing and dimension table, please see end of data
sheet, or Appendix D of Burr-Brown IC Data Book.
ORDERING INFORMATION
TEMPERATURE
MODEL
PACKAGE
RANGE
3583AM
8-Pin TO-3
25
C to +85
C
3583JM
8-Pin TO-3
0
C to +70
C
1
2
3
7
8
5
6
+V
CC
V
CC
NC
(1)
Output
+In
Offset
Trim
to V+ Supply
4
NOTE: (1) No internal connection.
Optional socket available: 804MC
In
100k
Offset
Trim
Optional
Offset
Adjust
4
3583
TYPICAL PERFORMANCE CURVES
(CONT)
T
CASE
= +25
C,
V
CC
= 150VDC, unless otherwise noted.
5
3583
TYPICAL PERFORMANCE CURVES
(CONT)
T
CASE
= +25
C,
V
CC
= 150VDC, unless otherwise noted.
3583
0.1F
0.1F
V+
50V to 150V
R
2
R
1
V
O
G = 1 +
R
2
R
1
Connect case
to ground.
V
+50V to +150V
3
4
100k
V+
Optional offset
voltage trim
circuit.
V
IN
3583
FIGURE 1. Basic Circuit Connections.
APPLICATION INFORMATION
Figure 1 shows the basic connections required to operate the
3583. Power supply bypass capacitors should be connected
close to the device pins. Be sure that these capacitors have an
adequate voltage rating.
Input offset voltage and drift of the 3583 are laser-trimmed.
Many applications require no external offset trimming.
Figure 1 also shows connection of an optional offset trim
potentiometer connected to pins 3 and 4.
FET input circuitry reduces the input bias current of the 3583
to less than 20pA at room temperature. Input bias current
remains nearly constant throughout the full common-mode
range. Input bias current approximately doubles for each 10
C
increase in case temperature above 25
C. Heat sinking can
help minimize this effect by reducing the case temperature.
Input circuitry of the 3583 is protected with series limiting
resistors and input clamp diodes. The inputs can withstand the
full rated supply voltage of
150V (common-mode or differ-
ential).
THERMAL PROTECTION
The 3583 has internal thermal shut-down circuitry that acti-
vates at a case temperature of approximately 150
C or higher.
As this circuitry is activated, the output current drive is
reduced. As the case temperature returns to less than the
activation temperature, operation will return to normal. A heat
sink may be required depending on load and signal conditions.
Note that a 75mA output may not be safe for all output
voltages--see typical performance curve "Safe Operating
Area". Applications such as current sources where output
voltage may be low (or the opposite polarity of the output
current) can overstress the output stage.
The thermal shut-down circuit will normally protect the
amplifier during a short-circuit to ground. It will not protect
against short-circuit to one of the power supplies. The typical
performance curve "Safe Operating Area" shows that the
large stress occurring during this high voltage condition may
cause damage if it exceeds 5ms duration. The thermal
protection circuitry will not activate fast enough to protect
the device from short-circuits to one of the power supplies.
The package case of the 3583 is electrically isolated from all
circuitry. No special insulating hardware is required.
Although not absolutely required, it is recommended that the
case be connected to ground.
PDF 
ZIP