Page 1
HPR10XX REV C 9/98
DC/DC CONVERTERS
HPR10XX
Notes: All dimensions are in inches (millimeters).
GRID: 0.100 inches (2.54 millimeters)
PIN PLACEMENT TOLERANCE: 0.015"
Internet: http://www.cdpowerelectronics.com
Power Electronics Division, United States
3400 E Britannia Drive, Tucson, Arizona 85706
Phone: 520.295.4100 Fax: 520.770.9369
Power Electronics Division, Europe
C&D Technologies (Power Electronics) Ltd.
132 Shannon Industrial Estate
,
Shannon, Co. Clare, Ireland
Tel: +353.61.474.133
Fax:+353.61.474.141
FEATURES
q
q
q
q
q
LOW COST
q
q
q
q
q
SINGLE-IN-LINE PACKAGE (SIP)
q
q
q
q
q
INTERNAL INPUT AND OUTPUT FILTERING
q
q
q
q
q
NON-CONDUCTIVE CASE
q
q
q
q
q
HIGH OUTPUT POWER DENSITY:
13 WATTS/INCH
3
q
q
q
q
q
EXTENDED TEMPERATURE RANGE:
-25C TO +65C
q
q
q
q
q
HIGH EFFICIENCY: TO 72% TYPICAL
DESCRIPTION
The HPR10XX Series uses advanced circuit design and pack-
aging technology to deliver superior reliability and perfor-
mance. A 170kHz push-pull oscillator is used in the input stage.
Beat-frequency oscillation problems are reduced when using
the HPR10XX Series with high frequency isolation amplifiers.
Reduced parts count and high efficiency add to the reliability of
the HPR10XX Series. The high efficiency of the HPR10XX
Series means less internal power dissipation, as low as 190mW.
With reduced heat dissipation the HPR10XX Series can oper-
ate at higher temperatures with no degradation. In addition, the
high efficiency of the HPR10XX Series means the series is able
to offer greater than 13 W/inch
3
of output power density.
Operation down to no load will not impact the reliability of the
series, although a 1mA minimum load is needed to realize
published specifications.
The HPR10XX Series provides the user low cost without
sacrificing reliability. The use of surface mounted devices and
advanced manufacturing technologies make it possible to offer
premium performance and low cost.
FRONT
VIEW
BOTTOM
VIEW
*
Common pin not present on single output models.
PIN CONNECTIONS
1. +VIN 2. -VIN
4. -VOUT 5. COM*
6. +VOUT
RIGHT
SIDE
VIEW
MECHANICAL
HPR10XX
Product Data Sheet
1.0 W
ATT
U
NREGULATED
SIP DC/DC C
ONVERTER
Page 2
HPR10XX REV C 9/98
Specifications typical at T
A
= +25C, nominal input voltage, rated output current unless otherwise specified.
ELECTRICAL SPECIFICATIONS
Note: Other input to output voltages may be available. Please contact factory.
COMMON SPECIFICATIONS
Specifications typical at T
A
= +25C, nominal input voltage, rated output current unless otherwise specified.
* For demonstrated MTTF results reference Reliability Report HPR105
NOMINAL
RATED
RATED
INPUT CURRENT REFLECTED
INPUT
OUTPUT
OUTPUT
RIPPLE EFFICIENCY
VOLTAGE
VOLTAGE
CURRENT
NO LOAD RATED LOAD CURRENT
MODEL
(V
DC
)
(V
DC
)
(mA)
(mA) (mA)
(mAp-p)
(%)
HPR1000
5
5
200
33
290
8
68
HPR1001
5
12
83
33
290
8
69
HPR1002
5
15
67
33
285
8
70
HPR1003
5
5
100
33
285
8
70
HPR1004
5
12
42
33
285
8
70
HPR1005
5
15
34
33
285
8
70
HPR1006
12
5
200
18
110
10
70
HPR1007
12
12
83
18
107
10
71
HPR1008
12
15
67
18
107
10
71
HPR1009
12
5
100
18
107
10
71
HPR1010
12
12
42
18
107
10
71
HPR1011
12
15
34
18
107
10
71
HPR1012
15
5
200
15
96
10
70
HPR1013
15
12
83
15
94
10
70
HPR1014
15
15
67
15
94
10
71
HPR1015
HPR1016
15
12
42
15
94
10
71
HPR1017
15
15
34
15
94
10
71
HPR1018
24
5
200
12
60
15
71
HPR1019
24
12
83
12
60
15
71
HPR1020
24
15
67
12
58
15
72
HPR1021
24
5
100
12
58
15
72
HPR1022
24
12
42
12
58
15
72
HPR1023
24
15
34
12
58
15
72
PARAMETER
CONDITIONS
MIN
TYP MAX
UNITS
INPUT
Voltage Range
4.5
5
5.5
V
DC
10.8
12
13.2
V
DC
13.5
15
16.5
V
DC
21.6
24
26.4
V
DC
Voltage Rise Time See Typical Performance Curves & Application Notes: "Capacitive Loading Effects on Start-Up of DC/DC Converters"
ISOLATION
Rated Voltage
1000
V
DC
Test Voltage
60 Hz, 10 Seconds
1000
Vpk
Resistance
10
G
Capacitance
25
100
pF
Leakage Current
V
ISO
= 240VAC, 60Hz
2
8.5
Arms
OUTPUT
Rated Power
1.0
W
Voltage Setpoint Accuracy
Rated Load, Nominal V
IN
5
%
Ripple & Noise
BW = DC to 10MHz
100
mVp-p
BW =10Hz to 2MHz
30
mVrms
Voltage
1mA Load, V
OUT
= 5V
7
V
DC
1mA Load, V
OUT
= 12V
15
V
DC
1mA Load, V
OUT
= 15V
18
V
DC
Temperature Coefficent
.01
%/Deg C
REGULATION
Line Regulation
High Line to Low Line
1
%/%Vin
Load Regulation (5V out only)
Rated Load to 1mA Load
10
%
Load Regulation (All other Models)
Rated Load to 1mA Load
3
%
GENERAL
Switching Frequency
170
kHz
Frequency Change
Over Line and Load
24
%
Package Weight
2
g
MTTF per MIL-HDBK-217, Rev. E
Circuit Stress Method
Ground Benign
T
A
= +25C
3.8
MHr
Fixed Ground
T
A
= +35C
1.4
MHr
Naval Sheltered
T
A
= +35C
685
kHr
Airborne Uninhabited Fighter
T
A
= +35C
211
kHr
TEMPERATURE
Specification
-25
+25
+65
C
Storage
-50
+110
C
Page 3
HPR10XX REV C 9/98
SAFE OPERATING AREA
Rise Time of Input Voltage (mS)
LOAD CAPACITANCE vs INPUT RISE TIME
(5 Vout models)
T
otal Load Capacitance (uF)
0 5 10 15 20 25 30 35 40 45 50
600
500
400
300
200
100
0
SAFE OPERATING AREA
Rise Time of Input Voltage (mS)
LOAD CAPACITANCE vs INPUT RISE TIME
(12 Vout models)
T
otal Load Capacitance (uF)
0 5 10 15 20 25 30 35 40 45 50
90
80
70
60
50
40
30
20
10
0
SAFE OPERATING AREA
Rise Time of Input Voltage (mS)
LOAD CAPACITANCE vs INPUT RISE TIME
(15 Vout models)
T
otal Load Capacitance (uF)
0 5 10 15 20 25 30 35 40 45 50
60
50
40
30
20
10
0
VOUT VS LOAD
(5Vout Models)
VOUT VS LOAD
(5Vout Models)
VOUT VS LOAD
(12Vout Models)
VOUT VS LOAD
(12Vout Models)
VOUT VS LOAD
(15Vout Models)
VOUT VS LOAD
(15Vout Models)
0
40
120
160
5.3
5.5
5.7
4.9
5.1
0
20
40
60
80
11.9
12.0
12.1
12.2
12.3
12.4
0
20
40
60
80
4.6
4.8
5.0
5.2
5.4
0
10
20
30
40
12.0
12.1
12.2
12.3
12.4
12.5
14.9
15.1
15.3
15.5
15.7
15.9
0
20
40
60
80
0
13.5
14.0
14.5
15.0
15.5
16.0
V
out
V
out
V
out
V
out
V
out
V
out
Ef
ficiency (%)
80
Output Current (mA)
Output Current each load (mA)
Output Current each load (mA)
12.5
Output Current each load (mA)
12.6
Output Current each load (mA)
Output Power each load (Watts)
0.2
0.4
0.6
0.8
1.0
16.5
0
40
80
100
60
20
90
75
60
45
30
15
0
EFFICIENCY VS LOAD
% of Rated Load (%)
Ef
ficiency (%)
OSCILLATION FREQUENCY VS
TEMPERATURE
220
200
180
160
140
-30
0
30
60
90
Temperature (C)
T
YPICAL PERFORMANCE CURVES
Specifications typical at T
A
= +25C, nominal input voltage, rated output current unless otherwise specified.
SAFE OPERATING AREA
NOTES:
1.) When operated within the SAFE OPERATING AREA as defined
by the above curves, the output voltage of HPR10XX devices is
guaranteed to be within 95% of its steady-state value within 100
milliseconds after the input voltage has reached 95% of its steady-
state value.
2.) For dual output models, total load capacitance is the sum of the
capacitances on the plus and minus outputs.
Page 4
HPR10XX REV C 9/98
The information provided herein is believed to be reliable; however, C&D TECHNOLOGIES assumes no responsibility for inaccuracies or omissions. C&D TECHNOLOGIES assumes no responsibility for the use of
this information, and all use of such information shall be entirely at the user's own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein
are implied or granted to any third party. C&D TECHNOLOGIES does not authorize or warrant any C&D TECHNOLOGIES product for use in life support devices/systems or in aircraft control applications.
ENGINEERING NOTES
ORDERING INFORMATION
Device Family
HPR Indicates DC/DC Converter
Model Number
Selected from Table of Electrical Characteristics
Screening Option
HPR 10XX /H
ABSOLUTE MAXIMUM RATINGS
Internal Power Dissipation.....................................................490mW
Short Circuit Duration......................................................Momentary
Lead Temperature (soldering, 10 seconds max)..................+300C
PDF 
ZIP