Specifications are subject to change without notice (01.09.99)
1
Dupline
Field- and Installationbus
Receivers with voltage signal output
Voltage output signals: 1 x 0 to 10 VDC
8-bit (8 channels) resolution
For binary transmitted analog signals
Galvanically separated output
D-housing
Plug-in type module
AC power supply
Type: Dupline
Output signal
Supply
Dupline analog receiver with
standard voltage output sig-
nal (0 to 10 VDC).
Convert binary codes into
analog voltage signals.
Ordering Key
Product Description
Type Selection
Supply
Ordering no.
0 to 10 VDC
24 VAC
FAD 1533 024
120 VAC
FAD 1533 120
220 VAC
FAD 1533 220
Code module
FMK A to FMK P
Output Specifications
Output
1 voltage output
Signal range
0 to 10 VDC
Isolated in groups of
1 x 1
Output load resistance
1 k
Resolution
8 bits (39.22 mV/LSB)
Settling time
1 pulse train + 1 ms
Short-circuit protection
None
Open loop voltage
10 VDC
Inaccuracy
1% of full scale
Cable length
3 m
Dielectric voltage
Output - Dupline
200 VAC (rms)
Accuracy
< 1%
Supply Specifications
Power supply
Overvoltage cat. III (IEC 60664)
Rated operational voltage
through pins A1 & A2 220
230 VAC +6%,
-15% (IEC 60038)
120
120 VAC 10% (IEC 60038)
024
24 VAC 10%
Frequency
45 to 65 Hz
Voltage interruption
40 ms
Rated operational voltage
typ. 2.5 VA
Rated impulse
withstand voltage
220
4 kV
120
2.5 kV
024
800 V
Dielectric voltage
Supply - Dupline
2 kVAC (rms)
Supply - Output
2 kVAC (rms)
General Specifications
Output-off delay
upon loss of Dupline carrier
Undefined
Power-on delay
Undefined,
1 s
Environment
Degree of protection
IP 20
Pollution degree
3 (IEC 60664)
Operating temperature
-20 to +50C (-4 to +122F)
Storage temperature
-50 to +85C (-58 to +185F)
Humidity (non-condensing)
20 to 80%
Mechanical resistance
Shock
15 G (11 ms)
Vibration
2 G (6 to 55 Hz)
Dimensions
Material
(see "Technical Information")
D-housing
Weight
200 g
Approvals
CSA, UL
Receiver with Analog Voltage Output
Type FAD 1533
FAD 1533 024
2
Specifications are subject to change without notice (01.09.99)
FAD 1533
Mode of Operation
Operation Diagram
Receiver with unipolar volt-
age signal output. The binary
status of an entire channel
group (8 bit) is converted to a
voltage signal. The binary
status of the selected group
may be generated by Dupline
transmitters with analog in-
puts (current, voltage, tem-
perature etc.) or by PC's.
The least significant bit (influ-
encing the output voltage by
39.22 mV) is the highest
channel of the selected group
(E8 if FMK E is plugged in).
The most significant bit (influ-
encing the output voltage by
4.98 V) is the lowest channel
of the selected channel group
(E1 in the above example).
Note: Analog receivers must
not be used in systems where
channel generators with 3
sequences are installed.
Output
signal
Accessories
Wiring Diagram
S: signal wire
Load
Socket
D 411
Socket cover
BB 5
Hold down spring
HF
Front mounting bezel
FRS 2
DIN-rail for D 411
FMD 411
For further information refer to "Accessories".
MSB =
Most Significant Bit
LSB =
Least Significant Bit
Channel status
Power
Supply
PDF 
ZIP