THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
HTTP://WWW.CONWIN.COM
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
The Connor-Winfield
VSLD824C1 is a surface
mount 3.3V Voltage
Controlled Crystal Oscillator
(VCXO) with an HCMOS
output. Based on a
fundamental design the
VSLD824C1 is designed for
phased lock loop applications
requiring low jitter and tight
stability.
1
2
VSLD824C1 - 77.76MHz
VCXO
SERIES
CENTER
FREQUENCY
FEATURES
DESCRIPTION
ORDERING INFORMATION
3.3V OPERATION
TOTAL FREQUENCY TOLERANCE:
20ppm
LOW JITTER <1ps RMS
TEMPERATURE RANGE: -20 to 70C
SURFACE MOUNT PACKAGE
TAPE AND REEL PACKAGING
SURFACE MOUNT 3.3V HCMOS VCXO
VSLD824C1
Vx502
00
1/29/04
CW 0701
VSLD824C1
77.76M
ABSOLUTE MAXIMUM RATINGS
TABLE 1.0
PARAMETER
UNITS
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Storage Temperature
-40
-
85
C
Supply Voltage
(Vcc)
-0.5
-
7.0
Vdc
Control Voltage
(Vc)
-0.5
-
7.0
Vdc
OPERATING SPECIFICATIONS
TABLE 2.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Center Frequency
(Fo)
2
-
100
MHz
Frequency Calibration
-10
-
10
1
Frequency Stability vs. Temperature
-20
-
20
ppm
2
Frequency Stability vs. change in supply
voltage
-10
-
10
ppm
Frequency Stability vs. load changes
-5
-
5
ppm
Aging (1st year)
-5
-
5
ppm
Total Frequency Tolerance
-50
-
50
ppm
3
Operating Temperature Range
-20
-
70
C
Supply Voltage
(Vcc)
3.135
3.300
3.465
Vdc
Supply Current
(Icc)
-
-
60
mA
Jitter (BW=10Hz to 20MHz)
-
-
5
pS rms
Jitter (BW=12kHz to 20MHz)
-
-
1
pS rms
SSB Phase Noise at 10Hz offset
-
-65
-
dBc/Hz
SSB Phase Noise at 100Hz offset
-
-95
-
dBc/Hz
SSB Phase Noise at 1KHz offset
-
-130
-
dBc/Hz
SSB Phase Noise at 10KHz offset
-
-135
-
dBc/Hz
SSB Phase Noise at 100KHz offset
-
-140
-
dBc/Hz
FREQUENCY CONTROL
TABLE 3.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Control Voltage Range
(Vc)
0.3
1.65
3.0
Vdc
Frequency Pullability
100
-
-
ppm
Absolute Pull Range
50
-
-
ppm
4
Monotonic Linearity
-10
-
10
%
Input Impedance
-
50K
-
Ohm
Modulation Bandwidth (3dB)
15
-
-
KHz
HCMOS OUTPUT CHARACTERISTICS
TABLE 4.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
LOAD
-
-
15
pF
Voltage (High)
(Voh)
2.8
2.4
-
Vdc
(Low)
(Vol)
-
0.3
0.4
Vdc
Current (High)
(Ioh)
-8
-
-
mA
(Low)
(Ioh)
-
-
8
mA
Duty Cycle at 50% of Vcc
40
50
60
%
Rise / Fall Time 10% to 90%
-
-
3
nS
PACKAGE CHARACTERISTICS
TABLE 5.0
Package
Non-hermetic package consisting of an FR4 substrat e with grounded metal
cover.
PROCESS RECOMMENDATIONS
TABLE 6.0
Solder Reflow
The component solder used internal to this device has a m elting point of
221
C. The peak temperature inside the device should be less than or
equal to 220
C for a maximum of 10 seconds
Wash
Ultrasonic cleaning is not recommended.
Notes
1.0
Nominal frequency tolerance after reflow soldering, Vc=1.65V, @ 25
C.
2.0
Referenced to Fo @ 25C. Positive Slope.
3.0
Inclusive of calibration, frequency vs. temperature s tability, supply voltage change, load change, shock and vibration and
aging over 15 years, Vc=2.5 Vdc.
4.0
Absolute pull range (APR) is the minimum guaranteed pul l range of the VCXO under all conditions over lifetime operation.
The APR is referenced to Fo.
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
HTTP://WWW.CONWIN.COM
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
2
2
Vx502
00
1/29/04
C
W
V
S
L
D
8
2
4
C
1
7
7
.
7
6
M
D
A
T
E
C
O
D
E
90%
50%
10%
15pF
CONTROL
VOLTAGE
Dimensional Tolerance:
.005 (.127mm)
PDF 
ZIP