BYM13-20 THRU BYM13-60
SGL41-20 THRU SGL41-60
SURFACE MOUNT SCHOTTKY BARRIER RECTIFIER
Reverse Voltage - 20 to 60 Volts Forward Current - 1.0 Ampere
FEATURES
Plastic package has carries Underwriters Laboratory
Flammability Classifications 94V-0
For surface mounted applications
Metal silicon junction, majority carrier conduction
High surge capability
Low power loss, high efficiency
High current capability, low forward voltage drop
For use in low voltage, high frequency inverters, free
wheeling and polarity protection applications
Guardring for overvoltage protection
High temperature soldering guaranteed:
250C/10 seconds at terminals
MECHANICAL DATA
Case: JEDEC DO-213AB molded plastic body
Terminals: Solder plated, solderable per MIL-STD-750,
Method 2026
Polarity: Two bands indicate cathode end 1st band denotes
device type 2nd band denotes voltage type
Mounting Position: Any
Weight: 0.116 gram, 0.0041 ounce
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25C ambient temperature unless otherwise specified.
BYM13
SYMBOLS
-20
-30
-40
-50
-60
UNITS
Denotes Schottky devices: 1st band is orange
SGL41-20
SGL41-30
SGL41-40
SGL41-50
SGL41-60
Polarity color bands (2nd band) voltage type
Gray
Red
Orange
Yellow
Green
Maximum repetitive peak reverse voltage
V
RRM
20
30
40
50
60
Volts
Maximum RMS voltage
V
RMS
14
21
28
35
42
Volts
Maximum DC blocking voltage
V
DC
20
30
40
50
60
Volts
Maximum average forward rectified current
(SEE FIG. 1)
I
(AV)
1.0
Amp
Peak forward surge current
8.3ms single half sine-wave superimposed
I
FSM
30.0
Amps
on rated load (JEDEC Method)
Maximum instantaneous forward voltage at 1.0A
V
F
0.50
0.70
Volts
(NOTE 1)
Maximum reverse current
T
A
=25C
0.5
at rated DC blocking voltage
(NOTE 1)
T
A
=100C
I
R
10
5.0
mA
Typical junction capacitance
(NOTE 2)
C
J
110
80.0
pF
Maximum thermal resistance
(NOTE 4)
R
JA
75.0
(NOTE 3)
R
JT
30.0
C/W
Operating junction temperature range
T
J
-55 to +125
-55 to +150
C
Storage temperature range
T
STG
-55 to +150
C
NOTES:
(1) Pulse test: 300
s pulse width, 1% duty cycle
(2) Measured at 1 MHz and applied reverse voltage of 4.0 Volts
(3) Thermal resistance junction to terminal, 0.24 x 0.24" (6.0 x 6.0mm) copper pads to each terminal
(4) Thermal resistance junction to ambient, 0.24 x 0.24" (6.0 x 6.0mm) copper pads to each terminal
10/98
DO-213AB
Dimensions in inches and (millimeters)
0
25
50
75
100
125
150
175
0
0.25
0.50
0.75
1.0
1
100
5.0
10
15
20
25
30
10
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
0.01
0.1
1
10.0
50
0.1
1
10
40
100
10
100
400
0
20
40
60
80
100
0.001
0.01
0.1
1
10
100
RATINGS AND CHARACTERISTIC CURVES BYM13-20 THRU BYM13-60, SGL41-20 THRU SGL41-60
T
J
=125C
T
J
=150C
FIG. 1 - FORWARD CURRENT DERATING CURVE
TERMINAL TEMPERATURE, C
A
VERA
GE FOR
W
ARD CURRENT
,
AMPERES
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT
NUMBER OF CYCLES AT 60 Hz
PEAK FOR
W
ARD SURGE CURRENT
,
AMPERES
FIG. 3 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
INST
ANT
ANEOUS FOR
W
ARD CURRENT
,
AMPERES
INST
ANT
ANEOUS REVERSE CURRENT
,
MILLIAMPERES
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
JUNCTION CAP
A
CIT
ANCE, pF
REVERSE VOLTAGE, VOLTS
AT RATED T
d
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)
T
J
=75C
T
J
=25C
T
J
=25C
SGL41-20 - SGL41-40
SGL41-50 & SGL41-60
PULSE WIDTH = 300
s
1% DUTY CYCLE
T
J
=25C
f=1.0 MHz
Vsig=50mVp-p
P.C.B. MOUNTED
on 0.24 x 0.24"
(6.0 x 6.0mm)
COPPER LAND
AREAS
SGL41-20 - SGL41-40
SGL41-50 & SGL41-60
T
J
=125C
RESISTIVE OR
INDUCTIVE LOAD
SGL41-20 - SGL41-40
SGL41-50 & SGL41-60
SGL41-20 -SGL41-40
SGL41-50 & SGL41-60
PDF 
ZIP