4/98
GBL005 THRU GBL10
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
Reverse Voltage - 50 to 1000 Volts
Forward Current - 4.0 Amperes
FEATURES
Plastic package has Underwriters Laboratory Flammability
Classification 94V-0
This series is UL listed under the Recognized Component
Index, file number E54214
Glass passivated chip junctions
High case dielectric strength
Typical I
R
less than 0.1
A
High surge current capability
Ideal for printed circuit boards
High temperature soldering guaranteed:
260C/10 seconds, 0.375" (9.5mm) lead length,
5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: Molded plastic body over passivated junctions
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
Mounting Position: Any
Weight: 0.071 ounce, 2.0 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25C ambient temperature unless otherwise specified.
GBL
GBL
GBL
GBL
GBL
GBL
GBL
SYMBOLS
005
01
02
04
06
08
10
UNITS
Maximum repetitive peak reverse voltage
V
RRM
50
100
200
400
600
800
1000
Volts
Maximum RMS voltage
V
RMS
35
70
140
280
420
560
700
Volts
Maximum DC blocking voltage
V
DC
50
100
200
400
600
800
1000
Volts
Maximum average forward
T
C
=50C
(NOTE 1)
4.0
rectified output current at
T
A
=40C
(NOTE 2)
I
(AV)
3.0
Amps
Peak forward surge current, single half sine-wave
superimposed on rated load (JEDEC Method) T
J
=150C
I
FSM
150.0
Amps
Rating for fusing (t<8.3ms)
I
2
t
93.0
A
2
sec
Maximum instantaneous forward drop per leg
at 4.0 Amperes
V
F
1.1
Volts
Maximum DC reverse current at rated
T
A
=25C
5.0
DC blocking voltage per leg
T
A
=125C
I
R
500.0
A
Typical junction capacitance per leg
(NOTE 3)
C
J
95.0
40.0
pF
Typical thermal resistance per leg
(NOTE 1)
R
JA
22.0
(NOTE 2)
R
JL
3.5
C/W
Operating junction storage and temperature range
T
J,
T
STG
-55 to +150
C
NOTES:
(1) Unit mounted on 3.0 x 3.0 x 0.11" thick (7.5 x 7.5 x 0.3cm) Al. plate
(2) Unit mounted on P.C.B. at 0.375" (9.5mm) lead length and 0.5 x 0.5" (12 x12mm) copper pads
(3) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
Case Type GBL
0.125 (3.17)
x 45 degrees
Chamfer
0.080 (2.03)
0.060 (1.50)
0.095 (2.41)
0.080 (2.03)
0.825 (20.9)
0.815 (20.7)
0.050 (1.27)
0.040 (1.02)
Polarity shown on front side of case: positive lead by beveled corner
0.040 (1.02)
0.030 (0.76)
0.022 (0.56)
0.018 (0.46)
0.210
0.190
(5.3)
(4.8)
0.421 (10.7)
0.411 (10.4)
0.718 (18.2)
0.682 (17.3)
0.140 (3.56)
0.128 (3.25)
Lead Depth
0.098 (2.5)
0.075 (1.9)
0.098 (2.5)
0.075 (1.9)
0.022 (0.56)
0.018 (0.46)
Dimensions in inches and (millimeters)
0
50
100
150
0
1.0
2.0
3.0
4.0
5.0
1
10
100
0
50
100
150
0.4
0.6
0.8
1.0
1.2
1.4
1.6
0.01
0.1
1
10
100
0.1
1
10
100
10
100
1,000
0
20
40
60
80
100
0.01
0.1
1
10
100
500
0.01
0.1
1
10
100
0.1
1
10
100
RATINGS AND CHARACTERISTICS CURVES GBL005 THRU GBL10
FIG. 1 - DERATING CURVES OUTPUT RECTIFIED
CURRENT
AMBIENT TEMPERATURE, C
P.C.B. MOUNTING
0.47 x 0.47" (12 x 12mm)
COPPER PADS
0.375" (9.5mm) LEAD LENGTH
60Hz RESISTIVE OR INDUCTIVE LOAD
60 Hz RESISTIVE OR INDUCTIVE LOAD
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
T
J
=25C
PULSE WIDTH=300
s
1% DUTY CYCLE
FIG. 3 - TYPICAL FORWARD VOLTAGE
CHARACTERISTICS PER LEG
INSTANTANEOUS FORWARD CURRENT, AMPERES
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
PER LEG
REVERSE VOLTAGE, VOLTS
T
J
=25
C
f=1.0 MHz
Vsig=50mVp-p
T
A
=25C
HEAT-SINK
MOUNTING,
3.0 x 3.0 x 0.11" THK
(7.5 x 7.5 x 0.3cm)
AL. PLATE
AVERAGE FORWARD OUTPUT CURRENT,
AMPERES
FIG. 4 - TYPICAL REVERSE LEAKAGE
CHARACTERISTICS PER LEG
NUMBER OF CYCLES AT 60 Hz
PEAK FORWARD SURGE CURRENT,
AMPERES
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT PER LEG
T
A
=125C
FIG. 6 - TYPICAL TRANSIENT THERMAL
IMPEDANCE PER LEG
TRANSIENT
THERMAL IMPEDANCE,
C/W
t, HEATING TIME, sec.
50 - 400V
600 - 1000V
50 - 400V
600 - 1000V
T
J
= T
J
max.
SINGLE SINE-WAVE
(JEDEC Method)
JUNCTION
CAPACITANCE, pF
1.0 CYCLE
PDF 
ZIP