GBPC6005 THRU GBPC610
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
Reverse Voltage - 50 to 1000 Volts
Forward Current - 6.0 Amperes
FEATURES
Plastic package has carries Underwriters Laboratory
Flammability Classification 94V-0
This series is UL listed under recognized under Component
Index, file number E54214
Glass passivated chip junctions
High case dielectric strength of 1500 V
RMS
Typical I
R
less than 0.5
A
High forward surge current capability
Ideal for printed circuit boards
High temperature soldering guaranteed:
260C/10 seconds at 5lbs. (2.3 kg) tension
MECHANICAL DATA
Case: Molded plastic body over passivated junction
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
Mounting Position: Any
(NOTE 1)
Mounting Torque: 5.0 in. - lb. max.
Weight: 0.1 ounce, 2.8 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25C ambient temperature unless otherwise specified.
GBPC
GBPC
GBPC
GBPC
GBPC
GBPC
GBPC
SYMBOLS 6005
601
602
604
606
608
610
UNITS
Maximum repetitive peak reverse voltage
V
RRM
50
100
200
400
600
800
1000 Volts
Maximum RMS bridge input voltage
V
RMS
35
70
140
280
420
560
700
Volts
Maximum DC blocking voltage
V
DC
50
100
200
400
600
800
1000 Volts
Maximum average forward
T
C
=50C
(NOTE1, 2)
6.0
rectified output current at
T
A
=40C
(NOTE 3)
I
(AV)
3.0
Amps
Peak forward surge current single sine-wave
superimposed on rated load (JEDEC Method)
I
FSM
175.0
Amps
Rating for fusing (t<8.3ms)
I
2
t
127.0
A
2
sec
Maximum instantaneous forward voltage drop
per leg at 3.0 Amperes
V
F
1.0
Volts
Maximum DC reverse current at rated
T
A
=25C
5.0
DC blocking voltage per leg
T
A
=125C
I
R
500.0
A
Typical junction capacitance per leg
(NOTE 4)
C
J
186.0
90.0
pF
Typical thermal resistance per leg
(NOTE 3)
R
JA
22.0
C/W
(NOTE 2)
R
JC
7.3
Operating junction temperature range
T
J
-55 to +150
C
Storage temperature range
T
STG
-55 to +150
C
NOTES:
(1) Bolt down on heat-sink with silicone thermal compound between bridge and mounting surface for maximum heat transfer with #6 screw
(2) Unit mounted on 5.5 x 6.0 x 0.11" thick (14 x 15 x 0.3cm) Al. Plate
(3) Unit mounted on P.C.B. at 0.375" (9.5mm) lead length with 0.5 x 0.5" (12 x 12mm) copper pads
(4) Measured at 1 MHz and applied reverse voltage of 4.0 Volts
HOLE FOR
#6 SCREW
0.158 (4.01)
0.142 (3.61)
DIA.
0.128 (3.25)
0.048 (1.22)
0.200 (5.08)
0.160 (4.06)
0.750
(19.05)
MIN.
0.040 (1.02) TYP.
0.094 (2.4) x 45 degrees
0.445 (11.30)
0.405 (10.29)
0.630 (16.00)
0.590 (14.98)
AC
AC
Polarity shown on side of case: Positive lead by beveled corner
0.445 (11.30)
0.405 (10.29)
0.630 (16.00)
0.590 (14.98)
DIA.
0.042(1.07)
0.038(0.96)
Dimensions in inches and (millimeters)
Case Style GBPC
4/98
0
50
100
150
0
2.0
4.0
6.0
8.0
1
10
100
50
75
100
125
150
175
200
10
0.4
1.0
1.8
0.01
0.1
1
100
0.01
0.1
1
10
100
0.1
1
10
100
0.1
1
10
100
10
100
1,000
0.6
0.8
1.2
1.6
1.4
0
20
40
60
80
100
0.1
1
10
100
500
RATINGS AND CHARACTERISTICS CURVES GBPC6005 THRU GBPC610
FIG. 1 - DERATING CURVE OUTPUT RECTIFIED
CURRENT
TEMPERATURE, C
AMBIENT TEMPERATURE, T
A
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
T
J
=25C
PULSE WIDTH=300
s
1% DUTY CYCLE
FIG. 4 - TYPICAL FORWARD
CHARACTERISTICS PER LEG
INSTANTANEOUS FORWARD CURRENT,
AMPERES
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
PER LEG
REVERSE VOLTAGE, VOLTS
T
J
=25C
5.5 x 6.0 x 0.11" THK
(14 x 1.5" x 0.3cm)
AL. PLATE
AVERAGE FORWARD OUTPUT CURRENT,
AMPERES
FIG. 3 - TYPICAL REVERSE LEAKAGE
CHARACTERISTICS PER LEG
T
J
=T
J
max.
SINGLE HALF SINE-WAVE
(JEDEC Method)
NUMBER OF CYCLES AT 60 Hz
PEAK FORWARD SURGE CURRENT,
AMPERES
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT PER LEG
T
A
=125C
FIG. 6 - TYPICAL TRANSIENT THERMAL
IMPEDANCE
TRANSIENT THERMAL IMPEDANCE,
C/W
t, HEATING TIME, sec.
50 - 400V
600 - 1000V
P.C.B. MOUNTING,
0.375" (9.5mm) LEAD LENGTH
T
J
=100C
60 H
Z
RESISTIVE OR
INDUCTIVE LOAD
CASE TEMPERATURE, T
C
HEAT-SINK MOUNTING,
1.0 CYCLE
T
J
=25
C
f=1.0 MHz
Vsig=50mVp-p
JUNCTION
CAPACITANCE, pF
PDF 
ZIP