BYM11-50 THRU BYM11-1000
RGL41A THRU RGL41M
SURFACE MOUNT GLASS PASSIVATED JUNCTION FAST SWITCHING RECTIFIER
Reverse Voltage - 50 to 1000 Volts Forward Current - 1.0 Ampere
FEATURES
Plastic package has Underwriters Laboratory Flammability
Classification 94V-0
Capable of meeting environmental standards of MIL-S-19500
For surface mount applications
High temperature metallurgically bonded construction
Glass passivated cavity-free junction
Fast switching for high efficiency
High temperature soldering guaranteed:
450C/5 seconds at terminals. Complete device submersible
temperature of 260C for 10 seconds in solder bath
MECHANICAL DATA
Case: JEDEC DO-213AB molded plastic over glass body
Terminals: Plated terminals, solderable per MIL-STD-750,
Method 2026
Polarity: Two bands indicate cathode end -1st band denotes device
type and 2nd band denotes repetitive peak reverse voltage rating
Mounting Position: Any
Weight: 0.0046 ounce, 0.116 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25C ambient temperature unless otherwise specified.
BYM11
BYM11
BYM11
BYM11
BYM11
BYM11 BYM11
SYMBOLS -50
-100
-200
-400
-600
-800
-1000
UNITS
Fast switching time device: 1st band is Red
RGL
RGL
RGL
RGL
RGL
RGL
RGL
41A
41B
41D
41G
41J
41K
41M
Polarity color bands (2nd Band)
Gray
Red
Orange
Yellow
Green
Blue
Violet
Maximum repetitive peak reverse voltage
V
RRM
50
100
200
400
600
800 1000 Volts
Maximum RMS voltage
V
RMS
35
70
140
280
420
560
700
Volts
Maximum DC blocking voltage
V
DC
50
100
200
400
600
800
1000 Volts
Maximum average forward rectified current at T
T
=55C
I
(AV)
1.0
Amp
Peak forward surge current 8.3ms single half
sine-wave superimposed on rated load (JEDEC Method)
I
FSM
30.0
Amps
Maximum instantaneous forward voltage at 1.0A
V
F
1.3 Volts
Maximum DC reverse current
T
A
=25C 5.0
at rated DC blocking voltage
T
A
=125C
I
R
50.0
A
Maximum full load reverse current,
I
R(AV)
50.0
A
full cycle average at T
A
=55C
Maximum reverse recovery time
(NOTE 1)
t
rr
150
250
500
ns
Typical junction capacitance
(NOTE 2)
C
J
15.0
pF
Maximum thermal resistance
(NOTE 3)
R
JA
75.0
(NOTE 4)
R
JT
30.0
C/W
Operating junction and storage temperature range
T
J
, T
STG
-65 to +175
C
NOTES:
(1) Reverse recovery test conditions: I
F
=0.5A, I
R
=1.0A, I
rr
=0.25A
(2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(3) Thermal resistance from junction to ambient, 0.24 x 0.24" (6.0 x 6.0mm) copper pads to each terminal
(4) Thermal resistance from junction to terminal, 0.24 x 0.24" (6.0 x 6.0mm) copper pads to each terminal
10/98
DO-213AB
Dimensions in inches and (millimeters)
*
*
Glass-plastic encapsulation is covered by
Patent No. 3,996,602 and brazed-lead assembly to Patent No. 3,930,306
PATENTED*
2nd band denotes voltage type
2nd BAND
25
50
75
100
125
150
175
0
0.25
0.5
0.75
1.0
1.25
1
10
100
0
10
15
20
25
30
0.4
0.6
0.8
1.0
1.2
1.4
1.6
0.01
0.1
1
10
1
10
100
1
10
100
0
20
40
60
80
100
0.01
0.1
1
10
0.01
0.1
1
10
100
0.1
1
10
100
RATINGS AND CHARACTERISTIC CURVES BYM11-50 THRU BYM11-1000 / RGL41A THRU RGL41M
FIG. 1 - FORWARD CURRENT
DERATING CURVE
TERMINAL TEMPERATURE, C
A
VERA
GE FOR
W
ARD RECTIFIED CURRENT
,
AMPERES
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
NUMBER OF CYCLES AT 60 H
Z
PEAK FOR
W
ARD SURGE CURRENT
,
AMPERES
FIG. 3 - TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
INST
ANT
ANEOUS FOR
W
ARD CURRENT
,
AMPERES
INST
ANT
ANEOUS REVERSE CURRENT
,
MICR
O
AMPERES
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
CAP
A
CIT
ANCE, pF
REVERSE VOLTAGE, VOLTS
T
J
=T
J
max.
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)
T
J
=25C
T
J
=25C
PULSE WIDTH=300
s
1% DUTY CYCLE
T
J
=25C
f=1.0 MH
Z
Vsig=50mVp-p
RESISTIVE OR
INDUCTIVE LOAD
T
J
=100C
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE
TRANSIENT
THERMAL IMPED
ANCE (
C/W)
t, PULSE DURATION, sec
MOUNTED ON 0.20 x 0.27" (5 x 7mm)
COPPER PAD AREAS
PDF 
ZIP