TGL41-6.8 THRU TGL41-200A
SURFACE MOUNT T
RANS
Z
ORB
TM TRANSIENT VOLTAGE SUPPRESSOR
Breakdown Voltage - 6.8 to 200 Volts Peak Pulse Power - 400 Watts
FEATURES
Plastic package has Underwriters Laboratory
Flammability Classification 94V-0
For surface mounted applications
Glass passivated junction
Excellent clamping capability
Low incremental surge resistance
Fast response time typically less than 1.0ps from
0 Volts to V
(BR)
400W peak pulse capability with a 10/1000
s waveform,
repetition rate (duty cycle): 0.01%
For devices with V
(BR)
10V, I
D
are typically less
than 1.0
A
High temperature soldering guaranteed:
250C/10 seconds at terminals
MECHANICAL DATA
Case: JEDEC DO-213AB molded plastic body over
passivated junction
Terminals: Solder plated, solderable per MIL-STD-750,
Method 2026
Polarity: Blue bands denotes the cathode which is positive
with respect to the anode under normal TVS operation
Mounting Position: Any
Weight: 0.116 gram, 0.0046 ounce
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25C ambient temperature unless otherwise specified.
RATINGS
SYMBOL
VALUE
UNITS
Peak pulse power dissipation with a
10/1000
s waveform
(NOTE 1, FIG. 1)
P
PPM
Minimum 400
Watts
Steady state power dissipation at T
L
=75C
(NOTE 2)
P
M(AV)
1.0
Watt
Peak pulse current with a 10/1000
s waveform
(NOTE 1, FIG. 3)
I
PPM
SEE TABLE 1
Amps
Peak forward surge current, 8.3ms single half
sine-wave superimposed on rated load for unidirectional only
I
FSM
40.0
Amps
(JEDEC Method)
(NOTE 3)
Maximum instantaneous forward voltage at 25A
for unidirectional only
V
F
3.5
Volts
Operating junction and storage temperature range
T
J
, T
STG
-55 to +150
C
NOTES:
(1) Non-repetitive current pulse, per Fig. 3 and derated above T
A
=25C per Fig. 2
(2) Mounted on copper pads to each terminal of 0.31 in
2
(8.0 mm
2
) per Fig. 5
(3) Measured at 8.3ms single half sine-wave or equivalent square wave duty cycle=4 pulses per minute maximum
1/20/99
SOLDERABLE ENDS
1st BAND
0.022 (0.56)
0.018 (0.46)
0.205 (5.2)
0.185(4.7)
D1=
0.105
0.095
(2.67)
(2.41)
D2 = D1 + 0
- 0.008 (0.20)
1st band denotes type and positive end (cathode)
D2
Dimensions in inches and (millimeters)
DO-213AB
Available in uni-directional only
0
25
50
75
100
125
150
175
200
0
25
50
100
75
0
1.0
2.0
3.0
4.0
0
100
50
150
1
10
100
0
20
40
10
30
50
1.0
s
10
s
100
s
1.0ms
10ms
0.1
1.0
10
100
0.1
s
1.0
10
100
200
10
100
1,000
10,000
0
50
100
150
200
0
0.25
0.50
0.75
1.00
25
75
125
175
RATINGS AND CHARACTERISTIC CURVES TGL41-6.8A THRU TGL41-200A
FIG. 1 - PEAK PULSE POWER RATING CURVE
P
PPM
, PEAK PULSE POWER, kW
td, PULSE WIDTH, sec.
T
A
, AMBIENT TEMPERATURE, C
FIG. 4 - TYPICAL JUNCTION CAPACITANCE
FIG. 3 - PULSE WAVEFORM
t, TIME, ms
V
(BR)
, BREAKDOWN VOLTAGE, VOLTS
T
L,
LEAD TEMPERATURE,C
NUMBER OF CYCLES AT 60 H
Z
I
PPM,
PEAK PULSE CURRENT
, %
PEAK PULSE POWER (P
PP
) or CURRENT
(I
PP
)
DERA
TING IN PERCENT
AGE, %
C
J
, JUNCTION CAP
ACIT
ANCE, pF
I
FSM,
PEAK FOR
W
ARD SURGE CURRENT
,
AMPERES
NON-REPETITIVE
PULSE WAVEFORM
SHOWN in FIG. 3
T
A
=25C
TGL41-100 -
TGL41-200A
TGL41-6.8 -
TGL41-91A
T
A
=25C
PULSE WIDTH (td) is DEFINED
as the POINT WHERE the PEAK
CURRENT DECAYS to 50% of I
PP
tr=10
sec
T
J
=25C
f=1.0 MHz
Vsq=50MVpp
MEASURED at
ZERO BIAS
MEASURED at
STAND-OFF
VOLTAGE, V
WM
UNIDIRECTIONAL
0.31 x 0.31 x 0.08" COPPER PADS
(8 X 8 x 2mm)
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)
T
J
=T
J
max.
td
HALF VALUE - I
PP
2
10/1000
sec. WAVEFORM
as DEFINED by R.E.A.
FIG. 6 - MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT UNIDIRECTIONAL ONLY
PEAK VALUE
I
PPM
FIG. 5 - STEADY STATE POWER DERATING CURVE
PM
(A
V),
STEADY
ST
A
TE POWER DISSIP
A
TION,
W
A
TTS
FIG. 2 - PULSE DERATING CURVE
60 H
Z
RESISTIVE OR INDUCTIVE LOAD
PDF 
ZIP
