HRF-SW1040
Product Concept Advance Information
________________________________________________________________________________________________________
Web Site:
www.mysoiservices.com
Honeywell
Email:
mysoiservices@honeywell.com
Solid State Electronics Center
12001 State Highway 55
2002 1040W Published June 2002 Page 1
Plymouth, Minnesota 55441-4799
1-800-323-8295
4X6 RF Matrix Switch
Features
Dual Band (AMPS/PCS) Operation
High Isolation of ~ 25 dB
Low Insertion Loss of ~12dB
Integrated 2 bit CMOS Parallel Control Logic
Integrated ESD Protection on Digital I/O
Single 3V Positive Supply Voltage, AC Coupled RF
Ultra Small LPCC
TM
Packaging
Impedance matched for 50 Ohm systems
Product Description
The Honeywell HRF-SW1040 is a high performance four
(4) input by six (6) output RF distribution switch, that is
ideal for use in wireless basestation applications that
require minimum power and optimum integration. Under
independent parallel control, each of 4 inputs are
connected exclusively to any of 6 RF outputs. Dual
band operation is provided, allowing either 1 AMPS and
3 PCS or 3 AMPS and 1 PCS antenna connections.
The HRF-SW1040 is manufactured with Honeywell's
patented Silicon On Insulator (SOI) CMOS technology,
which provides the performance of GaAs with the
economy and integration capabilities of conventional
CMOS technology.
RF Electrical Specifications @ + 25
o
C
Functional Schematic
6-way
power
splitter
6-way
power
splitter
6-way
power
splitter
6-way
power
splitter
SP4T
SP4T
SP4T
SP4T
SP4T
SP4T
2
A
2
B
2
C
2
D
2
E
2
F
4
4
4
4
4
4
4
3
2
1
Parameter
Test Condition
Frequency
Minimum
Typical
Maximum
Units
Insertion Loss
High or Low band selected
12
13
dB
Insertion Loss Balance
Channel to Channel
+/- 0.5
dB
Input to Input Isolation
All states
824 1990 MHz
25
30
dB
Output to Output
Isolation
All states
824 1990 MHz
20
30
dB
dB
Input to Output
Isolation
Off state
824 1990 MHz
25
30
Input / Output VSWR
In band of selected frequency
band only
824 894 or
1850 - 1990
1.25:1
1.5:1
ratio
1dB Compression
Input Power
824 894 or
1850 - 1990
27
dBm
Input IP3
Input power referenced
824 894 or
1850 - 1990
47
dBm
Trise, Tfall
Ton, Toff
Transients
10% To 90%
50% Cntl To 90%/10%Rf
In-Band
50
70
10
nS
nS
mV
Results @ Vdd=3.3 +/- 10%, Vss = 0 unless otherwise stated, Z0= 50 ohms
HRF-SW1040
Product Concept Advance Information
________________________________________________________________________________________________________
Web Site:
www.mysoiservices.com
Honeywell
Email:
mysoiservices@honeywell.com
Solid State Electronics Center
12001 State Highway 55
2002 1040W Published June 2002 Page 2
Plymouth, Minnesota 55441-4799
1-800-323-8295
DC Electrical Specifications @ + 25
o
C
Absolute Maximum Ratings
1
Package Outline Drawing
Ask your local Honeywell representative for details.
Truth Table For Each Of Six (6) Outputs
Parameter
Minimum
Typical
Maximum
Units
Single V
DD
Supply Voltage
3.0
3.3
3.6
V
CMOS Logic Level (0)
0
0.8
V
CMOS Logic Level (1)
V
DD
0.8
V
DD
V
Input Leakage Current
50
uA
Static Supply Current
50
uA
Parameter
Absolute Maximum
Units
V
DD
+4.0
V
Vin Digital Logic 0
- 0.6
V
Vin Digital Logic 1
Vdd + 0.6
V
Maximum Input Power
> 33
dBm
ESD Voltage (Human Body Model), Digital I/O's
TBD
V
ESD Voltage (Human Body Model), RF I/O's
TBD
V
Operating Temperature
+85
Degrees C
Storage Temperature
+125
Degrees C
(Note 1) Operation beyond any of these parameters may cause permanent damage.
Latch-Up: Unlike conventional CMOS RF switches, Honeywell's Microwave SOI technology is immune to latch-up.
ESD Protection: Although this device contains ESD protection circuitry on all digital inputs, conventional precautions should be
taken to ensure that the Absolute Maximum Ratings are not exceeded.
C0
C1
RF Output
0
0
1
1
0
1
0
1
RFINPUT1
RFINPUT2
RFINPUT3
RFINPUT4
"0" = CMOS Low, "1" = CMOS High
HRF-SW1040
Product Concept Advance Information
________________________________________________________________________________________________________
Web Site:
www.mysoiservices.com
Honeywell
Email:
mysoiservices@honeywell.com
Solid State Electronics Center
12001 State Highway 55
2002 1040W Published June 2002 Page 3
Plymouth, Minnesota 55441-4799
1-800-323-8295
Pin Configuration
Ask your local Honeywell representative for details.
Performance Curves
1.9
1.8
2.0
-16
-21
-11
-15
-10
-5
0
5
-20
10
Frequency (GHz)
dB(S(5,3))
dB(S(5,5))
dB(S(3,3))
Insertion Loss
Return Loss
Input And Return Loss (dB) For High Band Channel Selection
850
800
900
-16
-21
-11
-25
-20
-15
-10
-5
-30
0
Frequency (MHz)
dB(S(10,4))
dB(S(10,10))
dB(S(4,4))
Return Loss
Insertion Loss
Input And Return Loss (dB) For Low Band Channel Selection
HRF-SW1040
Product Concept Advance Information
________________________________________________________________________________________________________
Web Site:
www.mysoiservices.com
Honeywell
Email:
mysoiservices@honeywell.com
Solid State Electronics Center
12001 State Highway 55
2002 1040W Published June 2002 Page 4
Plymouth, Minnesota 55441-4799
1-800-323-8295
Typical Application Circuit
Call Honeywell for details.
Evaluation Circuit Board Connections
Ask your local Honeywell representative for details.
Evaluation Circuit Board
Ask your local Honeywell representative for details.
Evaluation Circuit Board Layout Design Details
Ask your local Honeywell representative for details.
Ordering Information
LPCC
TM
is a registered Trademark of ASAT Ltd.
See ASAT LPCC Marketing Outline Drawing # GMJ00004 at http://www.asat.com for details.
Honeywell reserves the right to make changes to improve reliability, function or design. Honeywell does not assume
any liability arising out of the application or use of any product or circuit described herein; neither does it convey any
license under its patent rights nor the rights of others.
Ordering Number
Product
HRF-SW1040-B
HRF-SW1040-T
HRF-SW1040-E
Delivered In Chip Tubes
Delivered On Tape And Reel
2
Engineering Evaluation Board
(Note 2) Contact Honeywell for details
PDF 
ZIP