1
INDUSTRIAL TEMPERATURE RANGE
IDT74CBTLV3862
LOW-VOLTAGE 10-BIT BUS SWITCH WITH ACTIVE HIGH AND LOW ENABLES
APRIL 2002
2002 Integrated Device Technology, Inc.
DSC-5264/1
c
INDUSTRIAL TEMPERATURE RANGE
APPLICATIONS:
3.3V High Speed Bus Switching and Bus Isolation
FEATURES:
5
A/B bi-directional switch
Isolation Under Power-Off Conditions
Over-voltage tolerant
Latch-up performance exceeds 100mA
V
CC
= 2.3V - 3.6V, normal range
ESD >2000V per MIL-STD-883, Method 3015; >200V using
machine model (C = 200pF, R = 0)
Available in SSOP, QSOP, and TSSOP packages
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
IDT74CBTLV3862
LOW-VOLTAGE 10-BIT
BUS SWITCH WITH ACTIVE
HIGH AND LOW ENABLES
SIMPLIFIED SCHEMATIC, EACH
SWITCH
FUNCTIONAL BLOCK DIAGRAM
DESCRIPTION:
The CBTLV3862 provides ten bits of high-speed bus switching with low
on-state resistance of the switch allowing connections to be made with
minimal propagation delay.
The device is organized as one 10-bit bus switch. The switches are
controlled by independent active-low enable (OE) and active-high enable
(OE) controls.
To ensure the high-impedance state during power up or power down,
OE should be tied to V
CC
through a pullup resistor; the minimum value of
the resistor is determined by the current-sinking capability of the driver, and
OE should be tied to GND.
2
11
23
A1
A10
OE
SW
SW
B10
B1
22
13
OE
1
A
B
OE
OE
2
INDUSTRIAL TEMPERATURE RANGE
IDT74CBTLV3862
LOW-VOLTAGE 10-BIT BUS SWITCH WITH ACTIVE HIGH AND LOW ENABLES
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
Description
Max.
Unit
V
CC
Supply Voltage Range
0.5 to 4.6
V
V
I
Input Voltage Range
0.5 to 4.6
V
Continuous Channel Current
128
mA
I
IK
Input Clamp Current, V
I/O
< 0
50
mA
T
STG
Storage Temperature Range
65 to +150
C
NOTE:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
PIN CONFIGURATION
FUNCTION TABLE
(1)
OPERATING CHARACTERISTICS
(1)
Symbol
Parameter
Test Conditions
Min.
Max.
Unit
V
CC
Supply Voltage
2.3
3.6
V
V
IH
High-Level Control Input Voltage
V
CC
= 2.3V to 2.7V
1.7
--
V
V
CC
= 2.7V to 3.6V
2
--
V
IL
Low-Level Control Input Voltage
V
CC
= 2.3V to 2.7V
--
0.7
V
V
CC
= 2.7V to 3.6V
--
0.8
T
A
Operating Free-Air Temperature
40
+85
C
NOTE:
1. All unused control inputs of the device must be held at V
CC
or GND to ensure proper device operation.
A
10
B
9
A
9
B
8
GND
B
10
V
CC
OE
OE
A
1
B
1
A
2
B
2
A
3
B
3
A
4
B
4
A
5
B
5
A
6
B
6
A
7
B
7
A
8
11
14
10
15
12
13
24
1
2
23
3
22
4
21
5
20
6
19
7
18
8
17
9
16
SSOP/ QSOP/ TSSOP
TOP VIEW
Inputs
OE
OE
Function
L
L
Disconnect
L
H
Disconnect
H
L
A Port = B Port
H
H
Disconnect
3
INDUSTRIAL TEMPERATURE RANGE
IDT74CBTLV3862
LOW-VOLTAGE 10-BIT BUS SWITCH WITH ACTIVE HIGH AND LOW ENABLES
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Operating Condition: T
A
= 40C to +85C
NOTES:
1. Typical Values are at V
CC
= 3.3V, +25C ambient.
2. The increase in supply current is attributable to each input that is at the specified voltage level rather than V
CC
or GND.
3. This is measured by the voltage drop between the A and B terminals at the indicated current through the switch.
Symbol
Parameter
Test Conditions
Min.
Typ.
(1)
Max.
Unit
V
IK
Control Inputs, Data I/O
V
CC
= 3V, I
I
= 18mA
--
--
1.2
V
I
I
Control Inputs, Data I/O
V
CC
= 3.6V, V
I
= V
CC
or GND
--
--
1
A
I
OZ
Data I/O
V
CC
= 3.6V, V
O
= 0V or 3.6V switch disabled
--
--
5
A
I
OFF
V
CC
= 0V, V
I
or V
O
= 0V or 3.6V
--
--
50
A
I
CC
V
CC
= 3.6V, I
O
= 0, V
I
= V
CC
or GND
--
--
10
A
I
CC(2)
Control Inputs
V
CC
= 3.6V, one input at 3V, other inputs at V
CC
or GND
--
--
300
A
C
I
Control Inputs
V
I
= 3V or 0
--
4
--
pF
C
IO(OFF)
V
O
= 3V or 0 (switch off)
--
6
--
pF
V
CC
= 2.3V
V
I
= 0
I
O
= 64mA
--
5
8
Typ. at V
CC
= 2.5V
I
O
= 24mA
--
5
8
R
ON(3)
V
I
= 1.7V
I
O
= 15mA
--
27
40
V
I
= 0
I
O
= 64mA
--
5
7
V
CC
= 3V
I
O
= 24mA
--
5
7
V
I
= 2.4V
I
O
= 15mA
--
10
15
V
CC
= 2.5V 0.2V
V
CC
= 3.3V 0.3V
Symbol
Parameter
Min.
Max.
Min.
Max.
Unit
t
PD(1)
Propagation Delay
--
0.15
--
0.25
ns
A to B or B to A
t
EN
Output Enable Time
1
4.5
1
4.2
ns
OE to A or B
t
DIS
Output Disable Time
1
5
1
5
ns
OE to A or B
t
EN
Output Enable Time
1
4.5
1
4.2
ns
OE to A or B
t
DIS
Output Disable Time
1
5
1
6
ns
OE to A or B
NOTE:
1. The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance when driven by an ideal voltage source
(zero output impededance).
SWITCHING CHARACTERISTICS
4
INDUSTRIAL TEMPERATURE RANGE
IDT74CBTLV3862
LOW-VOLTAGE 10-BIT BUS SWITCH WITH ACTIVE HIGH AND LOW ENABLES
Open
V
LOAD
GND
V
CC
Pulse
Generator
D.U.T.
500
500
C
L
R
T
V
IN
V
OUT
(1, 2)
SAME PHASE
INPUT TRANSITION
OPPOSITE PHASE
INPUT TRANSITION
0V
0V
V
OH
V
OL
t
PLH
t
PHL
t
PHL
t
PLH
OUTPUT
V
IH
V
T
V
T
V
IH
V
T
CONTROL
INPUT
t
PLZ
0V
OUTPUT
NORMALLY
LOW
t
PZH
0V
SWITCH
CLOSED
OUTPUT
NORMALLY
HIGH
ENABLE
DISABLE
SWITCH
OPEN
t
PHZ
0V
V
OL +
V
LZ
V
OH
V
T
V
T
t
PZL
V
LOAD/2
V
LOAD/2
V
IH
V
T
V
OL
V
OH -
V
HZ
TEST CIRCUITS AND WAVEFORMS
Propagation Delay
Test Circuits for All Outputs
Enable and Disable Times
NOTE:
1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH.
DEFINITIONS:
C
L
= Load capacitance: includes jig and probe capacitance.
R
T
= Termination resistance: should be equal to Z
OUT
of the Pulse Generator.
NOTES:
1. Pulse Generator for All Pulses: Rate
10MHz; t
F
2.5ns; t
R
2.5ns.
2. Pulse Generator for All Pulses: Rate
10MHz; t
F
2ns; t
R
2ns.
Test
Switch
t
PLZ
/t
PZL
V
LOAD
t
PHZ
/t
PZH
GND
t
PD
Open
SWITCH POSITION
Symbol
V
CC(1)
= 3.3V0.3V
V
CC(2)
= 2.5V0.2V
Unit
V
LOAD
6
2 x Vcc
V
V
IH
3
Vcc
V
V
T
1.5
Vcc
/ 2
V
V
LZ
300
150
mV
V
HZ
300
150
mV
C
L
50
30
pF
TEST CONDITIONS
5
INDUSTRIAL TEMPERATURE RANGE
IDT74CBTLV3862
LOW-VOLTAGE 10-BIT BUS SWITCH WITH ACTIVE HIGH AND LOW ENABLES
ORDERING INFORMATION
IDT
XX
CBTLV
XXX
XX
Package
Device Type
Temp. Range
PY
Q
PG
74
Shrink Small Outline Package
Quarter-size Small Outline Package
Thin Shrink Small Outline Package
Low-Voltage 10-Bit Bus Switch
40C to +85C
3862
DATA SHEET DOCUMENT HISTORY
4/10/2002
Changed OE characteristics
CORPORATE HEADQUARTERS
for SALES:
for Tech Support:
2975 Stender Way
800-345-7015 or 408-727-6116
logichelp@idt.com
Santa Clara, CA 95054
fax: 408-492-8674
(408) 654-6459
www.idt.com
PDF 
ZIP