1
File Number
6010
DG506A, DG507A, DG509A
CMOS Analog Multiplexers
The DG506A, DG507A and DG509A are CMOS Monolithic
16-Channel/Dual 8-Channel and Dual 4-Channel Analog
Multiplexers, which can also be used as demultiplexers. An
enable input is provided. When the enable input is high, a
channel is selected by the address inputs, and when low, all
channels are off.
A channel in the ON state conducts current equally well in
both directions. In the OFF state each channel blocks
voltages up to the supply rails. The address inputs and the
enable input are TTL and CMOS compatible over the full
specified operating temperature range.
The DG506A, DG507A and DG509A are pinout compatible
with the industry standard devices.
Features
Low Power Consumption
TTL and CMOS-Compatible Address and Enable Inputs
44V Maximum Power Supply Rating
High Latch-Up Immunity
Break-Before-Make Switching
Alternate Source
Applications
Data Acquisition Systems
Communication Systems
Signal Multiplexing/Demultiplexing
Audio Signal Multiplexing
Part Number Information
PART NUMBER
TEMP.
RANGE (
o
C)
PACKAGE
PKG.
NO.
DG506AAK
-55 to 125
28 Ld CERDIP
F28.6
DG506ACJ
0 to 70
28 Ld PDIP
E28.6
DG506ACY
0 to 70
28 Ld SOIC
M28.3
DG507ABK
-25 to 85
28 Ld CERDIP
F28.6
DG507ACJ
0 to 70
28 Ld PDIP
E28.6
DG507ACY
0 to 70
28 Ld SOIC
M28.3
DG509ACJ
0 to 70
16 Ld PDIP
E16.3
DG509ACY
0 to 70
16 Ld SOIC
M16.3
PART NUMBER
TEMP.
RANGE (
o
C)
PACKAGE
PKG.
NO.
Pinouts
DG506A (PDIP, CERDIP, SOIC)
TOP VIEW
DG507A (PDIP, CERDIP, SOIC)
TOP VIEW
DG509A (PDIP, SOIC)
TOP VIEW
28
27
26
25
24
23
22
21
20
19
18
17
16
15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
V+
NC
NC
S
16
S
15
S
14
S
13
S
12
S
11
S
10
S
9
GND
NC
A
3
D
S
8
S
7
S
6
S
5
S
3
S
1
EN
A
0
A
1
A
2
V-
S
4
S
2
V+
D
B
NC
S
8B
S
7B
S
6B
S
5B
S
4B
S
3B
S
2B
S
1B
GND
NC
NC
D
A
S
8A
S
7A
S
6A
S
5A
S
3A
S
1A
EN
A
0
A
1
A
2
V-
S
4A
S
2A
28
27
26
25
24
23
22
21
20
19
18
17
16
15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
14
15
16
9
13
12
11
10
1
2
3
4
5
7
6
8
A
0
EN
V-
S
1A
S
2A
S
3A
D
A
S
4A
A
1
V+
S
1B
S
2B
S
3B
S
4B
D
B
GND
Data Sheet
May 2001
itle
G50
,
507
A,
509
b-
t
MO
na-
lti-
x-
)
utho
)
ey-
rds
ter-
rpo-
ion,
i-
n-
ctor,
lti-
xer,
x,
an-
l,
ched
eo)
re-
r ()
OCI
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143
|
Intersil and Design is a trademark of Intersil Americas Inc.
|
Copyright Intersil Americas Inc. 2001
OBSOLETE
PRODUCT
POSSIBLE
SUBSTITUT
E PRODUC
T
HI1-0506(C
ERDIP), DG
406(PLAST
IC),
HI1-0507(C
ERDIP), DG
407(PLAST
IC),
HI-0509, DG
409
4
Absolute Maximum Ratings
Thermal Information
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44V
V- to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V
Digital Inputs, V
S
, V
D
(Note 1). . . . . . . . . . . . . (V- -2V) To (V+ +2V)
Continuous Current, (Any Terminal Except S or D) . . . . . . . . . 30mA
Continuous Current, (S or D) . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA
Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle Max) . . . . . 40mA
Operating Conditions
Temperature Range
"A" Suffix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55
o
C to 125
o
C
"B" Suffix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25
o
C to 85
o
C
"C" Suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
o
C to 70
o
C
Thermal Resistance (Typical, Note 2)
JA
(
o
C/W)
JC
(
o
C/W)
28 Ld CERDIP Package. . . . . . . . . . . .
55
18
16 Ld PDIP Package . . . . . . . . . . . . . .
90
N/A
28 Ld PDIP Package . . . . . . . . . . . . . .
55
N/A
16 Ld SOIC Package . . . . . . . . . . . . . .
100
N/A
28 Ld SOIC Package . . . . . . . . . . . . . .
70
N/A
Maximum Junction Temperature
CERDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175
o
C
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
o
C
Maximum Storage Temperature
"A" and "B" Suffix . . . . . . . . . . . . . . . . . . . . . . . . . -65
o
C to 150
o
C
"C" Suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65
o
C to 125
o
C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300
o
C
(SOIC - Lead Tips Only)
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Signals on S
X
, D
X
, E
N
, or A
X
exceeding V+ or V- are clamped by internal diodes. Limit diode current to maximum current ratings.
2.
JA
is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
T
A
= 25
o
C, V+ = +15V, V- = -15V, GND = 0V, V
EN
= 2.4V, Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
"A" SUFFIX
"B" AND "C" SUFFIX
UNITS
(NOTE 4)
MIN
(NOTE 3)
TYP
(NOTE 4)
MAX
(NOTE 4)
MIN
(NOTE 3)
TYP
(NOTE 4)
MAX
DYNAMIC CHARACTERISTICS
Switching Time of
Multiplexer, t
TRANSITION
See Figure 1
-
0.6
1
-
0.6
-
s
Break-Before-Make
Interval, t
OPEN
See Figure 3
-
0.2
-
-
0.2
-
s
Enable Turn-ON Time,
t
ON(EN)
See Figure 2
-
1
1.5
-
1
-
s
Enable Turn-OFF Time,
t
OFF(EN)
See Figure 2
-
0.4
1.0
-
0.4
-
s
OFF Isolation, OIRR
V
EN
= 0V, R
L
= 1k
, C
L
= 15pF,
V
S
= 7V
RMS
, f = 500kHz (Note 5)
-
68
-
-
68
-
dB
Source OFF Capacitance,
C
S(OFF)
V
S
= 0V, V
EN
= 0V, f = 140kHz
DG506A, DG507A
-
6
-
-
6
-
pF
DG509A
-
5
-
-
5
-
pF
Drain OFF Capacitance,
C
D(OFF)
V
D
= 0V, V
EN
= 0V, f = 140kHz
DG506A
-
45
-
-
45
-
pF
DG507A
-
23
-
-
23
-
pF
DG509A
-
12
-
-
12
-
pF
Charge Injection, Q
See Figure 4
DG506A, DG507A
-
6
-
-
6
-
pC
DG509A
-
4
-
-
4
-
pC
DIGITAL INPUT CHARACTERISTICS
Address Input Current,
Input Voltage High, I
AH
V
A
= 2.4V
-10
-0.002
-
-10
-0.002
-
A
V
A
= 15V
-
0.006
10
-
0.006
10
A
Address Input Current
Input Voltage Low, I
AL
V
EN
= 2.4V
V
A
= 0V
-10
-0.002
-
-10
-0.002
-
A
V
EN
= 0V
-10
-0.002
-
-10
-0.0002
-
A
DG506A, DG507A, DG509A
5
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range,
V
ANALOG
(Note 7)
-15
-
+15
-15
-
+15
V
Drain-Source ON
Resistance, r
DS(ON)
Sequence Each
Switch ON
V
AL
= 0.8V
V
AH
= 2.4V
I
S
= -200
A, V
D
= +10V
-
270
400
-
270
450
I
S
= -200
A, V
D
= -10V
-
230
400
-
230
450
r
DS(ON)
Matching
Between Channels
-10V
V
S
+10V
-
6
-
-
6
-
%
Source OFF Leakage
Current, I
S(OFF)
V
EN
= 0V
V
S
= +10V, V
D
= -10V
-1
0.002
1
-5
0.002
5
nA
V
S
= -10V, V
D
= +10V
-1
-0.005
1
-5
-0.005
5
nA
Drain OFF Leakage
Current, I
D(OFF)
V
EN
= 0V
DG506A
V
S
= -10V, V
D
= +10V
-10
0.02
10
-20
0.02
20
nA
V
S
= +10V, V
D
= -10V
-10
-0.03
10
-20
-0.03
20
nA
DG507A
V
S
= -10V, V
D
= +10V
-5
0.007
5
-10
0.007
10
nA
V
S
= +10V, V
D
= -10V
-5
-0.015
5
-10
-0.015
10
nA
DG509A
V
S
= -10V, V
D
= +10V
-
0.005
10
-
0.005
20
nA
V
S
= +10V, V
D
= -10V
-10
-0.008
-
-20
-0.008
-
nA
Drain ON Leakage Current,
I
D(ON)
(Note 6)
Sequence Each
Switch ON
V
AL
= 0.8V
V
AH
= 2.4V
DG506A
V
D
= V
S(ALL)
= +10V
-10
0.03
10
-20
0.03
20
nA
V
D
= V
S(ALL)
= -10V
-10
-0.06
10
-20
-0.06
20
nA
DG507A
V
D
= V
S(ALL)
= +10V
-5
0.015
5
-10
0.015
10
nA
V
D
= V
S(ALL)
= -10V
-5
-0.03
5
-10
-0.03
10
nA
DG509A
V
D
= V
S(ALL)
= +10V
-
0.007
10
-
0.007
20
nA
V
D
= V
S(ALL)
= -10V
-10
-0.015
-
-20
-0.015
-
nA
POWER SUPPLY CHARACTERISTICS
Positive Supply Current,
I+
V
EN
= 5.0V, V
A
= 0V
(Enabled)
-
1.3
2.4
-
1.3
2.4
mA
Negative Supply Current,
I-
-1.5
-0.7
-
-1.5
-0.7
-
mA
Positive Supply Current,
I+ Standby
V
EN
= 0V, V
A
= 0V
(Standby)
-
1.3
2.4
-
1.3
2.4
mA
Negative Supply Current,
I- Standby
-1.5
-0.7
-
-1.5
-0.7
-
mA
Electrical Specifications
T
A
= 25
o
C, V+ = +15V, V- = -15V, GND = 0V, V
EN
= 2.4V, Unless Otherwise Specified
(Continued)
PARAMETER
TEST CONDITIONS
"A" SUFFIX
"B" AND "C" SUFFIX
UNITS
(NOTE 4)
MIN
(NOTE 3)
TYP
(NOTE 4)
MAX
(NOTE 4)
MIN
(NOTE 3)
TYP
(NOTE 4)
MAX
r
D S ON
(
)
r
DS(ON)MAX
r
DS ON
(
)
MI N
r
DS ON
(
)
AVG
-----------------------------------------------------------------------
=
DG506A, DG507A, DG509A
PDF 
ZIP
