1
FN8140.0
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-352-6832
|
Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2005. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
X60008B-25, X60008C-25, X60008D-25
Precision 2.5V FGATM Voltage Reference
FEATURES
Output Voltage: 2.500V
Absolute Initial Accuracy Options:
0.5mV & 1.0mV
Ultra Low Power Supply Current: 500nA
Low Temperature Coefficient options:
3, 5 & 10ppm/C
10 mA Source & Sink Current Capability
10 ppm/1000hrs Long Term Stability
Supply Voltage Range: 4.5V to 6.5V
5kV ESD (Human Body Model)
Standard Package: SOIC-8
Temp Range: -40C to +85C
DESCRIPTION
The X60008-25 FGATM voltage references are very
high precision analog voltage references fabricated in
Intersil's proprietary Floating Gate Analog technology,
which achieves superior levels of performance when
compared to conventional band gap, buried zener, or
X
FET
TM technologies.
FGATM voltage references feature very high initial
accuracy, very low temperature coefficient, excellent
long term stability, low noise and excellent line and
load regulation, at the lowest power consumption
currently available. These voltage references enable
advanced applications for precision industrial &
portable systems operating at significantly higher
accuracy and lower power levels than can be achieved
with conventional technologies.
APPLICATIONS
High Resolution A/Ds & D/As
Precision Current Sources
Smart sensors
Digital Meters
Precision Regulators
Strain Gage Bridges
Calibration Systems
Precision Oscillators
Threshold Detectors
V-F Converters
Battery Management Systems
Servo Systems
TYPICAL APPLICATION
V
IN
= +5.0V
0.1F
Serial
Bus
V
IN
V
OUT
GND
X60008-25
Enable
SCK
SDAT
A/D Converter
16 to 24-bit
REF IN
10F
0.001F
(
*
)
(
*
)
Also see Figure 3 in Applications Information
Data Sheet
March 15, 2005
2
FN8140.0
March 15, 2005
PACKAGE DIAGRAM
PIN CONFIGURATIONS
ORDERING INFORMATION
Pin Name
Description
GND
Ground Connection
V
IN
Power Supply Input Connection
V
OUT
Voltage Reference Output Connection
DNC
Do Not Connect; Internal Connection Must Be Left Floating
1
2
3
4
8
7
6
5
SOIC
V
IN
DNC
GND
X60008-XX
DNC
DNC
V
OUT
DNC
GND
Logo
Device Part Number
60008 = Standard
Grade
B = 0.5 mV, 3 ppm/C
C = 0.5 mV, 5 ppm/C
D = 1.0 mV, 10 ppm/C
Temperature Range
I = -40C to +85C
Package
S8 = 8 lead SOIC
V
OUT
Option
25 = 2.500V
X 60008 C I S8 25
X60008B-25
3
FN8140.0
March 15, 2005
ABSOLUTE MAXIMUM RATINGS
Storage Temperature Range..................-65C to +125C
Max Voltage Applied V
IN
to Gnd ...............-0.5V to +6.5V
Max Voltage Applied V
OUT
to Gnd
(*)
........-0.5V to +3.5V
Voltage on "DNC" pins......... No connections permitted to
these pins.
Lead Temperature, soldering
(*)
...........................+ 225C
(*) note: maximum duration = 10 seconds
RECOMMENDED OPERATING CONDITIONS
COMMENT
Absolute Maximum Ratings are limits which may result
in impaired reliability and/or permanent damage to the
device. These are stress ratings provided for informa-
tion only and functional operation of the device at
these or any other conditions beyond those indicated
in the operational sections of this specification are not
implied.
For guaranteed specifications and test conditions, see
Electrical Characteristics.
The guaranteed specifications apply only for the test
conditions listed. Some performance characteristics
may degrade when the device is not operated under
the listed test conditions.
ELECTRICAL CHARACTERISTICS
(Operating Conditions: V
IN
= 5.0V, I
OUT
= 0mA, C
OUT
= 0.001F, T
A
= -40 to +85C unless otherwise specified.)
Note:
1. Over the specified temperature range. Temperature coefficient is measured by the box method whereby the change in V
OUT
is divided
by the temperature range; in this case, -40C to +85C = 125C.
2. Thermal Hysteresis is the change in V
OUT
created by package stress @ T
A
= 25C after temperature cycling. V
OUT
is read initially at
T
A
= 25C; the X60008 is then cycled between Hot (85C) and Cold (-40C) before a second V
OUT
measurement is taken at 25C. The
deviation between the initial V
OUT
reading and the second V
OUT
reading is then expressed in ppm.
3. Guaranteed by device characterization and/or correlation to other device tests.
Temperature
Min.
Max.
Industrial
-40C
+85C
Symbol
Parameter
Conditions
Min
Typ
Max
Units
V
OUT
Output Voltage
2.500
V
V
OA
V
OUT
Accuracy
X60008B-25
X60008C-25
X60008D-25
T
A
= 25C
-0.50
-0.50
-1.00
+0.50
+0.50
+1.00
mV
I
IN
Supply Current
500
800
nA
V
IN
Input Voltage Range
4.5
6.5
V
TC V
OUT
Output Voltage
Temperature Coefficient
(1)
X60008B-25
X60008C-25
X60008D-25
3
5
10
ppm/
C
V
OUT
/
V
IN
Line Regulation
+4.5V
V
IN
+6.5V
100
V/V
V
OUT
/
I
OUT
Load Regulation
0mA
I
SOURCE
10mA
-10mA
I
SINK
0mA
10
20
40
80
V/mA
V
OUT
/
t
Long Term Stability
T
A
= 25C
10
ppm/
1000Hrs
V
OUT
/
T
A
Thermal Hysteresis
(2)
T = -40
C to +85
C
50
ppm
I
SC
Short Circuit Current
(3)
T
A
= 25C
50
80
mA
V
N
Output Voltage Noise
0.1Hz to 10Hz
30
V
pp
X60008B-25
4
FN8140.0
March 15, 2005
TYPICAL PERFORMANCE CHARACTERISTIC CURVES
(V
IN
= 5.0V, I
OUT
= 0mA, T
A
= 25C unless otherwise specified)
LINE REGULATION
LINE REGULATION
LOAD REGULATION
-0.3
-0.2
-0.1
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
-20
-15
-10
-5
0
5
10
15
20
SINKING
TEMPERATURE (
C)
SOURCING
I
OUT
(mA)
0.1Hz to 10Hz V
OUT
NOISE
1 Sec/div
10
V/div
Band Pass Filter with 1 zero at .1Hz and 2 poles at 10 Hz
DELTA V
O
(
V)
DELTA V
OUT
(mV)
V
OUT
(V)
(normailized to V
IN
= 5.00V)
V
OUT
(V)
(normailized to 2.5V at V
IN
= 5V)
V
IN
(V)
V
IN
(V)
+25
C -40C
+85
C
2.498
2.499
2.5
2.501
2.502
-40
-15
10
35
60
85
320nA
520nA
690nA
V
OUT
vs TEMPERATURE
Normalized to 25
C
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
1
10
100
1000
10000
100000
1000000
No Load
1nF Load
10nF
Load
100nF Load
FREQUENCY (Hz)
PSRR vs CAP Load
PSRR (dB)
4.5
5
5.5
6
6.5
-40
C
+25
C
+85
C
4.5
5
5.5
6
6.5
310nA
520nA
690nA
-100
-80
-60
-40
-20
0
20
40
60
80
2.49994
2.49996
2.49998
2.5
2.50002
2.50004
2.50006
2.50008
X60008B-25
5
FN8140.0
March 15, 2005
TYPICAL PERFORMANCE CHARACTERISTIC CURVES
(V
IN
= 5.0V, I
OUT
= 0mA, T
A
= 25C unless otherwise specified)
10mA LOAD TRANSIENT RESPONSE
500mV/DIV
C
L
= .001
F
IN
= -10mA
I
I
I
I
IN
= +10mA
1mS/DIV
50
A LOAD TRANSIENT RESPONSE
100mV/DIV
500
SEC/DIV
C
L
= .001
F
IN
= -50
A
IN
= +50
A
LINE TRANSIENT RESPONSE
LINE TRANSIENT RESPONSE
200mV/DIV
500
SEC/DIV
200mV/DIV
500
SEC/DIV
C
L
= 0
C
L
= .001
F
V
IN
= -500mV
V
IN
= +500mV
V
IN
= -500mV
V
IN
= +500mV
X60008B-25
6
FN8140.0
March 15, 2005
TYPICAL PERFORMANCE CHARACTERISTIC CURVES
(V
IN
= 5.0V, I
OUT
= 0mA, T
A
= 25C unless otherwise specified)
0
50
100
150
200
250
300
100
100
10
1000
10000
100000
no Load
1nF Load
10nF Load
100nF Load
0
1
2
3
4
5
6
-1
1
3
5
7
9
11
V
IN
V
OUT
Z
OUT
vs FREQUENCY
FREQUENCY (Hz)
Z
OUT
(
)
I
IN
(nA)
V
IN
(V)
I
IN
vs V
IN
I
IN
(nA)
V
IN
(V)
I
IN
vs V
IN
TURN-ON TIME
V
IN
& V
OUT
(V)
TIME (mSec)
0
100
200
300
400
500
600
700
800
4.5
5
5.5
6
6.5
3 units representative of I
IN
Range
480
500
520
540
560
580
600
4.5
5
5.5
6
6.5
-40C
+25C
+85C
X60008B-25
7
FN8140.0
March 15, 2005
APPLICATIONS INFORMATION
FGA Technology
The X60008 series of voltage references use the float-
ing gate technology to create references with very low
drift and supply current. Essentially the charge stored
on a floating gate cell is set precisely in manufacturing.
The reference voltage output itself is a buffered ver-
sion of the floating gate voltage. The resulting refer-
ence device has excellent characteristics which are
unique in the industry: very low temperature drift, high
initial accuracy, and almost zero supply current. Also,
the reference voltage itself is not limited by voltage
bandgaps or zener settings, so a wide range of refer-
ence voltages can be programmed (standard voltage
settings are provided, but customer-specific voltages
are available).
The process used for these reference devices is a
floating gate CMOS process, and the amplifier circuitry
uses CMOS transistors for amplifier and output tran-
sistor circuitry. While providing excellent accuracy,
there are limitations in output noise level and load reg-
ulation due to the MOS device characteristics. These
limitations are addressed with circuit techniques dis-
cussed in other sections.
Nanopower Operation
Reference devices achieve their highest accuracy
when powered up continuously, and after initial stabili-
zation has taken place. This drift can be eliminated by
leaving the power-on continuously.
The X60008 is the first high precision voltage reference
with ultra low power consumption that makes it possible
to leave power-on continuously in battery operated cir-
cuits. The X60008 consumes extremely low supply cur-
rent due to the proprietary FGA technology. Supply
current at room temperature is typically 500nA which is
1 to 2 orders of magnitude lower than competitive
devices. Application circuits using battery power will
benefit greatly from having an accurate, stable refer-
ence which essentially presents no load to the battery.
In particular, battery powered data converter circuits
that would normally require the entire circuit to be dis-
abled when not in use can remain powered up
between conversions as shown in figure 1. Data acqui-
sition circuits providing 12 to 24 bits of accuracy can
operate with the reference device continuously biased
with no power penalty, providing the highest accuracy
and lowest possible long term drift.
Other reference devices consuming higher supply cur-
rents will need to be disabled in between conversions
to conserve battery capacity. Absolute accuracy will
suffer as the device is biased and requires time to set-
tle to its final value, or, may not actually settle to a final
value as power-on time may be short.
Figure 1.
Board mounting Considerations
For applications requiring the highest accuracy, board
mounting location should be reviewed. Placing the
device in areas subject to slight twisting can cause
degradation of the accuracy of the reference voltage
due to die stresses. It is normally best to place the
device near the edge of a board, or the shortest side,
as the axis of bending is most limited at that location.
Obviously mounting the device on flexprint or
extremely thin PC material will likewise cause loss of
reference accuracy.
Noise Performance and Reduction:
The output noise voltage in a 0.1Hz to 10Hz
bandwidth is typically 30Vp-p. This is shown in the
plot in the Typical Performance Curves. The noise
measurement is made with a bandpass filter made of
a 1 pole high-pass filter with a corner frequency at
.1Hz and a 2-pole low-pass filter with a corner
frequency at 12.6Hz to create a filter with a 9.9Hz
bandwidth. Noise in the 10KHz to 1MHz bandwidth is
approximately 400Vp-p with no capacitance on the
output, as shown in Fig. 2 below. These noise
measurements are made with a 2 decade bandpass
filter made of a 1 pole high-pass filter with a corner
frequency at 1/10 of the center frequency and 1-pole
low-pass filter with a corner frequency at 10 times the
center frequency. Figure 2 also shows the noise in the
10KHz to 1MHz band can be reduced to about 50Vp-
p using a .001F capacitor on the output. Noise in the
1KHz to 100KHz band can be further reduced using a
0.1F capacitor on the output, but noise in the 1Hz to
100Hz band increases due to instability of the very low
power amplifier with a 0.1F capacitance load. For
V
IN
= 4.5V to 6.5V
0.001F
Serial
Bus
V
IN
V
OUT
GND
X60008-25
REF IN
Enable
SCK
SDAT
A/D Converter
12 to 24-bit
0.01F
10F
X60008B-25
8
FN8140.0
March 15, 2005
load capacitances above .001F the noise reduction
network shown in fig. 3 is recommended. This network
reduces noise sig-nificantly over the full bandwidth. As
shown in fig. 2, noise is reduced to less than 40Vp-p
from 1Hz to 1MHz using this network with a .01F
capacitor and a 2k
resistor in series with a 10F
capacitor.
Figure 2.
Figure 3.
Turn-On Time
The X60008 devices have ultra-low supply current and
thus the time to bias up internal circuitry to final values
will be longer than with higher power references. Nor-
mal turn-on time is typically 7ms. This is shown in the
graph, Figure 4. Since devices can vary in supply cur-
rent down to 300nA, turn-on time can last up to about
12ms. Care should be taken in system design to
include this delay before measurements or conver-
sions are started.
Figure 4.
Temperature Coefficient
The limits stated for temperature coefficient (tempco)
are governed by the method of measurement. The
overwhelming standard for specifying the temperature
drift of a reference is to measure the reference voltage
at two temperatures, take the total variation, (V
HIGH
-
V
LOW
), and divide by the temperature extremes of
measurement (T
HIGH
- T
LOW
). The result is divided by
the nominal reference voltage (at T = 25C) and multi-
plied by 10
6
to yield ppm/C. This is the "Box" method.
CL = 0
CL = .001F
CL = .1F
CL = .01F & 10F + 2k
400
350
300
250
200
150
100
50
0
1
10
100
1000
10000
100000
X60008-25 NOISE REDUCTION
NOISE VOLT
AGE (
Vp
-p
)
V
IN
= 6.5V
V
IN
V
O
GND
X60008-25
.01F
10F
2k
.1F
10F
0
1
2
3
4
5
6
-1
1
3
5
7
9
690 nA
520 nA
320 nA
V
IN
V
OUT
X60008 TURN-ON TIME (25
C)
TIME (mSec)
V
IN
& V
OUT
(V)
X60008B-25
9
FN8140.0
March 15, 2005
TYPICAL APPLICATION CIRCUITS
Precision 2.5V, 50mA Reference.
V
IN
= 5.2V to 6.5V
2N2905
2.5V/50mA
0.009F
V
IN
V
OUT
GND
X60008-25
Kelvin Sensed Load
0.1F
5.0V
V
IN
V
OUT
GND
X60008-25
V
OUT
Sense
Load
R = 200
+
V
IN
V
OUT
X60008-25
GND
4.5V to 6.5V
0.1F
0.01F
V
OUT
+
V
CC
R
H
R
L
X9119
V
SS
SDA
SCL
2-Wire Bus
V
OUT
(buffered)
2.5V Full Scale Low-Drift 10-bit Adjustable Voltage Source
X60008B-25
10
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN8140.0
March 15, 2005
PACKAGING INFORMATION
0.150 (3.80)
0.158 (4.00)
0.228 (5.80)
0.244 (6.20)
0.014 (0.35)
0.019 (0.49)
Pin 1
Pin 1 Index
0.010 (0.25)
0.020 (0.50)
0.050 (1.27)
0.188 (4.78)
0.197 (5.00)
0.004 (0.19)
0.010 (0.25)
0.053 (1.35)
0.069 (1.75)
(4X) 7
0.016 (0.410)
0.037 (0.937)
0.0075 (0.19)
0.010 (0.25)
0 - 8
X 45
8-Lead Plastic, SOIC, Package Code S8
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
0.250"
0.050" Typical
0.050"
Typical
0.030"
Typical
8 Places
FOOTPRINT
X60008B-25
PDF 
ZIP