ChipFind - документация

Электронный компонент: MX29LV081TC-70

Скачать:  PDF   ZIP
1
P/N:PM0717
REV. 1.0, JUL. 31, 2001
MX29LV081
PRELIMINARY
8M-BIT [1M x 8] CMOS SINGLE VOLTAGE
3V ONLY EQUAL SECTOR FLASH MEMORY
Status Reply
- Data polling & Toggle bit for detection of program and
erase operation completion.
Ready/Busy pin (RY/BY)
- Provides a hardware method of detecting program or
erase operation completion.
Sector protection
- Hardware method to disable any combination of
sectors from program or erase operations
- Any combination of sectors can be erased with erase
suspend/resume function.
- Tempoary sector unprotect allows code changes in
previously locked sectors.
100,000 minimum erase/program cycles
Latch-up protected to 100mA from -1V to VCC+1
Low VCC write inhibit is equal to or less than 2.3V
Package type:
- 40-pin TSOP
Compatibility with JEDEC standard
- Pinout and software compatible with single-power
supply Flash
FEATURES
Extended single - supply voltage range 2.7V to 3.6V
1,048,576 x 8
Single power supply operation
- 3.0V only operation for read, erase and program
operation
Fast access time: 70/90ns
Low power consumption
- 20mA maximum active current
- 0.2uA typical standby current
Command register architecture
- Byte/word Programming (7us/12us typical)
- Sector Erase (Sector structure 64K-Byte x16)
Auto Erase (chip & sector) and Auto Program
- Automatically erase any combination of sectors with
Erase Suspend capability.
- Automatically program and verify data at specified
address
Erase suspend/Erase Resume
- Suspends sector erase operation to read data from,
or program data to, any sector that is not being erased,
then resumes the erase.
GENERAL DESCRIPTION
The MX29LV081 is a 8-mega bit Flash memory orga-
nized as 1M bytes of 8 bits. MXIC's Flash memories
offer the most cost-effective and reliable read/write non-
volatile random access memory. The MX29LV081 is
packaged in 40-pin TSOP. It is designed to be repro-
grammed and erased in system or in standard EPROM
programmers.
The standard MX29LV081 offers access time as fast as
70ns, allowing operation of high-speed microprocessors
without wait states. To eliminate bus contention, the
MX29LV081 has separate chip enable (CE) and output
enable (OE) controls.
MXIC's Flash memories augment EPROM functionality
with in-circuit electrical erasure and programming. The
MX29LV081 uses a command register to manage this
functionality. The command register allows for 100%
TTL level control inputs and fixed power supply levels
during erase and programming, while maintaining maxi-
mum EPROM compatibility.
MXIC Flash technology reliably stores memory contents
even after 100,000 erase and program cycles. The MXIC
cell is designed to optimize the erase and programming
mechanisms. In addition, the combination of advanced
tunnel oxide processing and low internal electric fields
for erase and program operations produces reliable cy-
cling. The MX29LV081 uses a 2.7V~3.6V VCC supply
to perform the High Reliability Erase and auto Program/
Erase algorithms.
The highest degree of latch-up protection is achieved
with MXIC's proprietary non-epi process. Latch-up pro-
tection is proved for stresses up to 100 milliamps on
address and data pin from -1V to VCC + 1V.
2
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
PIN CONFIGURATIONS
PIN DESCRIPTION
SYMBOL
PIN NAME
A0~A19
Address Input
Q0~Q7
Data Input/Output
CE
Chip Enable Input
WE
Write Enable Input
RESET
Hardware Reset Pin/Sector Protect Unlock
OE
Output Enable Input
RY/BY
Ready/Busy Output
VCC
Power Supply Pin (2.7V~3.6V)
GND
Ground Pin
40 TSOP (Standard Type) (10mm x 20mm)
A16
A15
A14
A13
A12
A11
A9
A8
WE
RESET
NC
RY/BY
A18
A7
A6
A5
A4
A3
A2
A1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
A17
GND
NC
A19
A10
Q7
Q6
Q5
Q4
VCC
VCC
NC
Q3
Q2
Q1
Q0
OE
GND
CE
A0
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
MX29LV081
3
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
BLOCK STRUCTURE
Table 1: MX29LV081 SECTOR ARCHITECTURE
Sector
Sector Size
Address range
Sector Address
Byte Mode
Byte Mode (x8)
A19 A18 A17 A16 A15 A14 A13
SA0
64Kbytes
00000h-0FFFFh
0
0
0
0
X
X
X
SA1
64Kbytes
10000h-1FFFFh
0
0
0
1
X
X
X
SA2
64Kbytes
20000h-2FFFFh
0
0
1
0
X
X
X
SA3
64Kbytes
30000h-3FFFFh
0
0
1
1
X
X
X
SA4
64Kbytes
40000h-4FFFFh
0
1
0
0
X
X
X
SA5
64Kbytes
50000h-5FFFFh
0
1
0
1
X
X
X
SA6
64Kbytes
60000h-6FFFFh
0
1
1
0
X
X
X
SA7
64Kbytes
70000h-7FFFFh
0
1
1
1
X
X
X
SA8
64Kbytes
80000h-8FFFFh
1
0
0
0
X
X
X
SA9
64Kbytes
90000h-9FFFFh
1
0
0
1
X
X
X
SA10
64Kbytes
A0000h-AFFFFh
1
0
1
0
X
X
X
SA11
64Kbytes
B0000h-BFFFFh
1
0
1
1
X
X
X
SA12
64Kbytes
C0000h-CFFFFh
1
1
0
0
X
X
X
SA13
64Kbytes
D0000h-DFFFFh
1
1
0
1
X
X
X
SA14
64Kbytes
E0000h-EFFFFh
1
1
1
0
X
X
X
SA15
64Kbytes
F0000h-FFFFFh
1
1
1
1
X
X
X
4
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
BLOCK DIAGRAM
CONTROL
INPUT
LOGIC
PROGRAM/ERASE
HIGH VOLTAGE
WRITE
STATE
MACHINE
(WSM)
STATE
REGISTER
MX29LV081
FLASH
ARRAY
X-DECODER
ADDRESS
LATCH
AND
BUFFER
Y-PASS GATE
Y
-DECODER
ARRAY
SOURCE
HV
COMMAND
DATA
DECODER
COMMAND
DATA LATCH
I/O BUFFER
PGM
DATA
HV
PROGRAM
DATA LATCH
SENSE
AMPLIFIER
Q0-Q7
A0-A19
CE
OE
WE
RESET
5
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
AUTOMATIC PROGRAMMING
The MX29LV081 is byte programmable using the Auto-
matic Programming algorithm. The Automatic Program-
ming algorithm makes the external system do not need
to have time out sequence nor to verify the data pro-
grammed. The typical chip programming time at room
temperature of the MX29LV081 is less than 10 seconds.
AUTOMATIC PROGRAMMING ALGORITHM
MXIC's Automatic Programming algorithm requires the
user to only write program set-up commands (including
2 unlock write cycle and A0H) and a program command
(program data and address). The device automatically
times the programming pulse width, provides the pro-
gram verification, and counts the number of sequences.
The device provides an unlock bypass mode with faster
programming. Only two write cycles are needed to pro-
gram a word or byte, instead of four. A status bit similar
to DATA polling and a status bit toggling between con-
secutive read cycles, provide feedback to the user as
to the status of the programming operation. Refer to write
operation status, table 7, for more information on these
status bits.
AUTOMATIC SECTOR ERASE
The MX29LV081 is sector(s) erasable using MXIC's Auto
Sector Erase algorithm. The Automatic Sector Erase
algorithm automatically programs the specified sector(s)
prior to electrical erase. The timing and verification of
electrical erase are controlled internally within the de-
vice. An erase operation can erase one sector, multiple
sectors, or the entire device.
AUTOMATIC CHIP ERASE
The entire chip is bulk erased using 10 ms erase pulses
according to MXIC's Automatic Chip Erase algorithm.
Typical erasure at room temperature is accomplished in
less than 25 second. The Automatic Erase algorithm
automatically programs the entire array prior to electri-
cal erase. The timing and verification of electrical erase
are controlled internally within the device.
AUTOMATIC ERASE ALGORITHM
MXIC's Automatic Erase algorithm requires the user to
write commands to the command register using stan-
dard microprocessor write timings. The device will auto-
matically pre-program and verify the entire array. Then
the device automatically times the erase pulse width,
provides the erase verification, and counts the number
of sequences. A status bit toggling between consecu-
tive read cycles provides feedback to the user as to the
status of the erasing operation.
Register contents serve as inputs to an internal state-
machine which controls the erase and programming cir-
cuitry. During write cycles, the command register inter-
nally latches address and data needed for the program-
ming and erase operations. During a system write cycle,
addresses are latched on the falling edge, and data are
latched on the rising edge of WE or CE, whichever hap-
pens first.
MXIC's Flash technology combines years of EPROM
experience to produce the highest levels of quality, reli-
ability, and cost effectiveness. The MX29LV081 electri-
cally erases all bits simultaneously using Fowler-
Nordheim tunneling. The bytes are programmed by us-
ing the EPROM programming mechanism of hot elec-
tron injection.
During a program cycle, the state-machine will control
the program sequences and command register will not
respond to any command set. During a Sector Erase
cycle, the command register will only respond to Erase
Suspend command. After Erase Suspend is completed,
the device stays in read mode. After the state machine
has completed its task, it will allow the command regis-
ter to respond to its full command set.
AUTOMATIC SELECT
The auto select mode provides manufacturer and de-
vice identification, and sector protection verification,
through identifier codes output on Q7~Q0. This mode is
mainly adapted for programming equipment on the de-
vice to be programmed with its programming algorithm.
When programming by high voltage method, automatic
select mode requires VID (11.5V to 12.5V) on address
pin A9 and other address pin A6, A1 and A0 as referring
to Table 3. In addition, to access the automatic select
codes in-system, the host can issue the automatic se-
6
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
A19
A12
A9
A8
A6
A5
A1
A0
Description
CE
OE
WE
|
|
|
|
Q7~Q0
A13
A10
A7
A2
Read Silicon ID
L
L
H
X
X
VID
X
L
X
L
L
C2H
Manfacturer Code
Read Silicon ID
L
L
H
X
X
VID
X
L
X
L
H
38H
01H
Sector Protection
L
L
H
SA
X
VID
X
L
X
H
L
(protected)
Verification
00H
(unprotected)
TABLE 2. MX29LV081 AUTO SELECT MODE OPERATION
NOTE:SA=Sector Address, X=Don't Care, L=Logic Low, H=Logic High
lect command through the command register without
requiring VID, as shown in table4.
To verify whether or not sector being protected, the sec-
tor address must appear on the appropriate highest or-
der address bit (see Table 1 and Table 2). The rest of
address bits, as shown in table3, are don't care. Once
all necessary bits have been set as required, the pro-
gramming equipment may read the corresponding iden-
tifier code on Q7~Q0.
7
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
First Bus
Second Bus
Third Bus
Fourth Bus
Fifth Bus
Sixth Bus
Command
Bus
Cycle
Cycle
Cycle
Cycle
Cycle
Cycle
Cycle Addr
Data Addr
Data
Addr
Data Addr
Data
Addr
Data Addr
Data
Reset
1
XXXH F0H
Read
1
RA
RD
Read Manufacturer ID
4
XXXH AAH XXXH
55H
XXXH
90H X00H C2H
Read Silicon ID
4
XXXH AAH XXXH
55H
XXXH
90H ADI
DDI
Sector Protect
4
XXXH AAH XXXH
55H
XXXH
90H (SA)
00H
Verify
x02H
01H
Porgram
4
XXXH AAH XXXH
55H
XXXH
A0H PA
PD
Chip Erase
6
XXXH AAH XXXH
55H
XXXH
80H XXXH AAH
XXXH 55H
XXXH 10H
Sector Erase
6
AAAH AAH 555H
55H
AAAH
80H AAAH AAH
555H
55H
SA
30H
Sector Erase Suspend
1
XXXH B0H
Sector Erase Resume
1
XXXH 30H
TABLE 4. MX29LV081 COMMAND DEFINITIONS
Note:
1. ADI = Address of Device identifier; A1=0, A0 = 0 for manufacturer code,A1=0, A0 = 1 for device code. A2-A19=do not care.
(Refer to table 2)
DDI = Data of Device identifier : C2H for manufacture code, 38H for device code.
X = X can be VIL or VIH
RA=Address of memory location to be read.
RD=Data to be read at location RA.
2.PA = Address of memory location to be programmed.
PD = Data to be programmed at location PA.
SA = Address of the sector to be erased.
3. For Sector Protect Verify operation:If read out data is 01H, it means the sector has been protected. If read out data is 00H, it
means the sector is still not being protected.
8
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
ADDRESS
DESCRIPTION
CE
OE
WE
RESET
A19 A12
A9
A8
A6
A5
A1
A0
Q0~Q7
A13
A10
A7
A2
Read
L
L
H
H
AIN
Dout
Write
L
H
L
H
AIN
DIN(3)
Reset
X
X
X
L
X
High Z
Temproary sector Unprotect
X
X
X
VID
AIN
DIN
Output Disable
L
H
H
H
X
High Z
Standby
Vcc
0.3V
X
X
Vcc
0.3V
X
High Z
Sector Protect
L
H
L
VID
SA
X
X
X
L
X
H
L
X
Sector Unprotect
L
H
L
VID
SA
X
X
X
H
X
H
L
X
Sector Protection Verify
L
L
H
H
SA
X
VID
X
L
X
H
L
CODE(5)
TABLE 5. MX29LV081 BUS OPERATION
NOTES:
1. Manufacturer and device codes may also be accessed via a command register write sequence. Refer to Table 4.
2. VID is the Silicon-ID-Read high voltage, 11.5V to 12.5V.
3. Refer to Table 4 for valid Data-In during a write operation.
4. X can be VIL or VIH, L=Logic Low=VIL, H=Logic High=VIH.
5. Code=00H means unprotected.
Code=01H means protected.
6. A19~A13=Sector address for sector protect.
7. Sector Protection/Unprotect requires VID on the RESET pin only, and can be implemented either in system or via program-
ming equipment.
sequences. Note that the Erase Suspend (B0H) and
Erase Resume (30H) commands are valid only while the
Sector Erase operation is in progress.
COMMAND DEFINITIONS
Device operations are selected by writing specific ad-
dress and data sequences into the command register.
Writing incorrect address and data values or writing them
in the improper sequence will reset the device to the
read mode. Table 4 defines the valid register command
9
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
REQUIREMENTS FOR READING ARRAY
DATA
To read array data from the outputs, the system must
drive the CE and OE pins to VIL. CE is the power control
and selects the device. OE is the output control and gates
array data to the output pins. WE should remain at VIH.
The internal state machine is set for reading array data
upon device power-up, or after a hardware reset. This
ensures that no spurious alteration of the memory contect
occurs during the power transition. No command is
necessary in this mode to obtain array data. Standard
microprocessor read cycles that assert valid address on
the device address inputs produce valid data on the device
data outputs. The device remains enabled for read access
until the command register contents are altered.
WRITE COMMANDS/COMMAND
SEQUENCES
To program data to the device or erase sectors of memory
, the sysytem must drive WE and CE to VIL, and OE to
VIH.
The device features an Unlock Bypass mode to facilitate
faster programming. Once the device enters the Unlock
Bypass mode, only two write cycles are required to
program a byte, instead of four. The "byte Program
Command Sequence" section has details on
programming data to the device using both standard and
Unlock Bypass command sequences.
An erase operation can erase one sector, multiple sectors
, or the entire device. Table indicates the address space
that each sector occupies. A "sector address" consists
of the address bits required to uniquely select a sector.
The "Writing specific address and data commands or
sequences into the command register initiates device
operations. Table 1 defines the valid register command
sequences. Writing incorrect address and data values or
writing them in the improper sequence resets the device
to reading array data."section has details on erasing a
sector or the entire chip, or suspending/resuming the erase
operation.
After the system writes the autoselect command
sequence, the device enters the autoselect mode. The
system can then read autoselect codes from the internal
reqister (which is separate from the memory array) on
Q7-Q0. Standard read cycle timings apply in this mode.
Refer to the Autoselect Mode and Autoselect Command
Sequence section for more information.
ICC2 in the DC Characteristics table represents the
active current specification for the write mode. The "AC
Characteristics" section contains timing specification
table and timing diagrams for write operations.
STANDBY MODE
When using both pins of CE and RESET, the device
enter CMOS Standby with both pins held at Vcc
0.3V.
IF CE and RESET are held at VIH, but not within the
range of VCC
0.3V, the device will still be in the standby
mode, but the standby current will be larger. During Auto
Algorithm operation, Vcc active current (Icc2) is required
even CE = "H" until the operation is complated. The de-
vice can be read with standard access time (tCE) from
either of these standby modes, before it is ready to read
data.
OUTPUT DISABLE
With the OE input at a logic high level (VIH), output from
the devices are disabled. This will cause the output pins
to be in a high impedance state.
RESET OPERATION
The RESET pin provides a hardware method of resetting
the device to reading array data. When the RESET pin is
driven low for at least a period of tRP, the device
immediately terminates any operation in progress,
tristates all output pins, and ignores all read/write
commands for the duration of the RESET pluse. The
device also resets the internal state machine to reading
array data. The operation that was interrupted should be
reinitated once the device is ready to accept another
command sequence, to ensure data integrity
Current is reduced for the duration of the RESET pulse.
When RESET is held at VSS
0.3V, the device draws
CMOS standby current (ICC4). If RESET is held at VIL
but not within VSS
0.3V, the standby current will be
greater.
The RESET pin may be tied to system reset circuitry. A
system reset would that also reset the Flash memory,
enabling the system to read the boot-up firm-ware from
10
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
READ/RESET COMMAND
The read or reset operation is initiated by writing the
read/reset command sequence into the command reg-
ister. Microprocessor read cycles retrieve array data.
The device remains enabled for reads until the command
register contents are altered.
If program-fail or erase-fail happen, the write of F0H will
reset the device to abort the operation. A valid com-
mand must then be written to place the device in the
desired state.
SILICON-ID READ COMMAND
Flash memories are intended for use in applications where
the local CPU alters memory contents. As such, manu-
facturer and device codes must be accessible while the
device resides in the target system. PROM program-
mers typically access signature codes by raising A9 to
a high voltage(VID). However, multiplexing high voltage
onto address lines is not generally desired system de-
sign practice.
The MX29LV081 contains a Silicon-ID-Read operation
to supple traditional PROM programming methodology.
The operation is initiated by writing the read silicon ID
command sequence into the command register. Fol-
lowing the command write, a read cycle with A1=VIL,
A0=VIL retrieves the manufacturer code of C2H. A read
cycle with A1=VIL, A0=VIH returns the device code of
38H for MX29LV081.
SET-UP AUTOMATIC CHIP/SECTOR ERASE
COMMANDS
Chip erase is a six-bus cycle operation. There are two
"unlock" write cycles. These are followed by writing the
"set-up" command 80H. Two more "unlock" write cy-
cles are then followed by the chip erase command 10H
or sector erase command 30H.
The Automatic Chip Erase does not require the device
to be entirely pre-programmed prior to executing the Au-
tomatic Chip Erase. Upon executing the Automatic Chip
Erase, the device will automatically program and verify
the entire memory for an all-zero data pattern. When the
device is automatically verified to contain an all-zero
pattern, a self-timed chip erase and verify begin. The
erase and verify operations are completed when the data
on Q7 is "1" at which time the device returns to the
Read mode. The system is not required to provide any
control or timing during these operations.
When using the Automatic Chip Erase algorithm, note
that the erase automatically terminates when adequate
erase margin has been achieved for the memory array(no
erase verification command is required).
If the Erase operation was unsuccessful, the data on
Q5 is "1"(see Table 7), indicating the erase operation
exceed internal timing limit.
The automatic erase begins on the rising edge of the
last WE or CE pulse, whichever happens first in the
command sequence and terminates when the data on
Q7 is "1" and the data on Q6 stops toggling for two con-
secutive read cycles, at which time the device returns
to the Read mode.
the Flash memory.
If RESET is asserted during a program or erase
operation, the RY/BY pin remains a "0" (busy) until the
internal reset operation is complete, which requires a
time of tREADY (during Embedded Algorithms). The
sysytem can thus monitor RY/BY to determine whether
the reset operation is complete. If RESET is asserted
when a program or erase operation is commpleted within
a time of tREADY (not during Embedded Algorithms).
The system can read data tRH after the RESET pin
returns to VIH.
Refer to the AC Characteristics tables for RESET
parameters and to Figure 20 for the timing diagram.
11
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
READING ARRAY DATA
The device is automatically set to reading array data
after device power-up. No commands are required to
retrieve data. The device is also ready to read array data
after completing an Automatic Program or Automatic
Erase algorithm.
After the device accepts an Erase Suspend command,
the device enters the Erase Suspend mode. The sys-
tem can read array data using the standard read tim-
ings, except that if it reads at an address within erase-
suspended sectors, the device outputs status data. After
completing a programming operation in the Erase
Suspend mode, the system may once again read array
data with the same exception. See rase Suspend/Erase
Resume Commands" for more infor-mation on this mode.
The system
must
issue the reset command to re-en-
able the device for reading array data if Q5 goes high, or
while in the autoselect mode. See the "Reset Command"
section, next.
RESET COMMAND
Writing the reset command to the device resets the
device to reading array data. Address bits are don't care
for this command.
The reset command may be written between the se-
quence cycles in an erase command sequence before
erasing begins. This resets the device to reading array
data. Once erasure begins, however, the device ignores
reset commands until the operation is complete.
The reset command may be written between the se-
quence cycles in a program command sequence be-fore
programming begins. This resets the device to reading
array data (also applies to programming in Erase
Suspend mode). Once programming begins,however, the
device ignores reset commands until the operation is
complete.
The reset command may be written between the se-
quence cycles in an SILICON ID READ command
sequence. Once in the SILICON ID READ mode, the
reset command
must
be written to return to reading array
data (also applies to SILICON ID READ during Erase
Suspend).
If Q5 goes high during a program or erase operation,
writing the reset command returns the device to read-
ing
array data (also applies during Erase Suspend).
Pins
A0
A1
Q7
Q6
Q5
Q4
Q3
Q2
Q1
Q0
Code(Hex)
Manufacture code
VIL
VIL
1
1
0
0
0
0
1
0
C2H
Device code
VIH
VIL
0
0
1
0
0
1
1
0
38H
Sector Protection
X
VIH
0
0
0
0
0
0
0
1
01H (Protected)
Verification
X
VIH
0
0
0
0
0
0
0
0
00H (Unprotected)
TABLE 6. SILICON ID CODE
12
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
SECTOR ERASE COMMANDS
The Automatic Sector Erase does not require the de-
vice to be entirely pre-programmed prior to executing
the Automatic Sector Erase Set-up command and Au-
tomatic Sector Erase command. Upon executing the
Automatic Sector Erase command, the device will auto-
matically program and verify the sector(s) memory for
an all-zero data pattern. The system is not required to
provide any control or timing during these operations.
When the sector(s) is automatically verified to contain
an all-zero pattern, a self-timed sector erase and verify
begin. The erase and verify operations are complete
when the data on Q7 is "1" and the data on Q6 stops
toggling for two consecutive read cycles, at which time
the device returns to the Read mode. The system is not
required to provide any control or timing during these
operations.
When using the Automatic sector Erase algorithm, note
that the erase automatically terminates when adequate
erase margin has been achieved for the memory array
(no erase verification command is required). Sector
erase is a six-bus cycle operation. There are two "un-
lock" write cycles. These are followed by writing the
set-up command 80H. Two more "unlock" write cycles
are then followed by the sector erase command 30H.
The sector address is latched on the falling edge of WE
or CE, whichever happens later, while the command(data)
is latched on the rising edge of WE or CE, whichever
happens first. Sector addresses selected are loaded
into internal register on the sixth falling edge of WE or
CE, whichever happens later. Each successive sector
load cycle started by the falling edge of WE or CE,
whichever happens later must begin within 50us from
the rising edge of the preceding WE or CE, whichever
happens first. Otherwise, the loading period ends and
internal auto sector erase cycle starts. (Monitor Q3 to
determine if the sector erase timer window is still open,
see section Q3, Sector Erase Timer.) Any command other
than Sector Erase(30H) or Erase Suspend(B0H) during
the time-out period resets the device to read mode.
ERASE SUSPEND
This command only has meaning while the state ma-
chine is executing Automatic Sector Erase operation,
and therefore will only be responded during Automatic
Sector Erase operation. When the Erase Suspend Com-
mand is issued during the sector erase operation, the
device requires a maximum 20us to suspend the sector
erase operation. However, when the Erase Suspend com-
mand is written during the sector erase time-out, the
device immediately terminates the time-out period and
suspends the erase operation. After this command has
been executed, the command register will initiate erase
suspend mode. The state machine will return to read
mode automatically after suspend is ready. At this time,
state machine only allows the command register to re-
spond to Erase Resume, program data to , or read data
from any sector not selected for erasure.
The system can determine the status of the program
operation using the Q7 or Q6 status bits, just as in the
standard program operation. After an erase-suspend pro-
gram operation is complete, the system can once again
read array data within non-suspended sectors.
ERASE RESUME
This command will cause the command register to clear
the suspend state and return back to Sector Erase mode
but only if an Erase Suspend command was previously
issued. Erase Resume will not have any effect in all
other conditions. Another Erase Suspend command can
be written after the chip has resumed erasing.
WORD/BYTE PROGRAM COMMAND SEQUENCE
The device programs one byte of data for each program
operation. The command sequence requires four bus
cycles, and is initiated by writing two unlock write cycles,
followed by the program set-up command. The program
address and data are written next, which in turn initiate
the Embedded Program algorithm. The system is
not
required to provide further controls or timings. The device
automatically generates the program pulses and verifies
the programmed cell margin. Table 1 shows the address
and data requirements for the byte program command
sequence.
When the Embedded Program algorithm is complete,
the device then returns to reading array data and
addresses are no longer latched. The system can
determine the status of the program operation by using
Q7, Q6, or RY/BY. See "Write Operation Status" for
information on these status bits.
Any commands written to the device during the Em-
13
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
WRITE OPERSTION STATUS
The device provides several bits to determine the sta-
tus of a write operation: Q2, Q3, Q5, Q6, Q7, and RY/
BY. Table 10 and the following subsections describe the
functions of these bits. Q7, RY/BY, and DQ6 each offer
a method for determining whether a program or erase
operation is complete or in progress. These three bits
are discussed first.
Q7: Data Polling
The Data Polling bit, Q7, indicates to the host sys-tem
whether an Automatic Algorithm is in progress or com-
pleted, or whether the device is in Erase Suspend. Data
Polling is valid after the rising edge of the final WE pulse
in the program or erase command sequence.
During the Automatic Program algorithm, the device out-
puts on Q7 the complement of the datum programmed
to Q7. This Q7 status also applies to programming dur-
ing Er ase Suspend. When the Automatic Program algo-
rithm is complete, the device outputs the datum pro-
grammed to Q7. The system must provide the program
address to read valid status information on Q7. If a pro-
gram address falls within a protected sector, Data Poll-
ing on Q7 is active for approximately 1 us, then the de-
vice returns to reading array data.
During the Automatic Erase algorithm, Data Polling pro-
duces a "0" on Q7. When the Automatic Erase algo-
rithm is complete, or if the device enters the Erase Sus-
pend mode, Data Polling produces a "1" on Q7. This is
analogous to the complement/true datum out-put de-
scribed for the Automatic Program algorithm: the erase
bedded Program Algorithm are ignored. Note that a
hardware reset immediately terminates the programming
operat ion. The Byte Program command sequence should
be reinitiated once the device has reset to reading array
data, to ensure data integrity.
Programming is allowed in any sequence and across
sector boundaries. A bit cannot be programmed from a
"0" back to a "1". Attempting to do so may halt the
operation and set Q5 to "1" ," or cause the Data Polling
algorithm to indicate the operation was successful.
However, a succeeding read will show that the data is
still "0". Only erase operations can convert a "0" to a
"1".
function changes all the bits in a sector to "1" prior to
this, the device outputs the "complement," or "0"." The
system must provide an address within any of the sec-
tors selected for erasure to read valid status information
on Q7.
After an erase command sequence is written, if all sec-
tors selected for erasing are protected, Data Polling on
Q7 is active for approximately 100 us, then the device
returns to reading array data. If not all selected sectors
are protected, the Automatic Erase algorithm erases the
unprotected sectors, and ignores the selected sectors
that are protected.
When the system detects Q7 has changed from the
complement to true data, it can read valid data at Q7-Q0
on the following read cycles. This is because Q7 may
change asynchr onously with Q0-Q6 while Output En-
able (OE) is asserted low.
RY/BY:Ready/Busy
The RY/BY is a dedicated, open-drain output pin that
indicates whether an Automatic Erase/Program algorithm
is in progress or complete. The RY/BY status is valid
after the rising edge of the final WE or CE, whichever
happens first, in the command sequence. Since RY/BY
is an open-drain output, several RY/BY pins can be tied
together in parallel with a pull-up resistor to Vcc.
If the output is low (Busy), the device is actively erasing
or programming. (This includes programming in the Erase
Suspend mode.)If the output is high (Ready), the device
is ready to read array data (including during the Erase
Suspend mode), or is in the standby mode.
Table 7 shows the outputs for RY/BY during write opera-
tion.
Q6:Toggle BIT I
Toggle Bit I on Q6 indicates whether an Automatic Pro-
gram or Erase algorithm is in progress or complete, or
whether the device has entered the Erase Suspend mode.
Toggle Bit I may be read at any address, and is valid
after the rising edge of the final WE or CE, whichever
happens first, in the command sequence(prior to the pro-
gram or erase operation), and during the sector time-
out.
14
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
During an Automatic Program or Erase algorithm opera-
tion, successive read cycles to any address cause Q6
to toggle. The system may use either OE or CE to con-
trol the read cycles. When the operation is complete, Q6
stops toggling.
After an erase command sequence is written, if all sec-
tors selected for erasing are protected, Q6 toggles and
returns to reading array data. If not all selected sectors
are protected, the Automatic Erase algorithm erases the
unprotected sectors, and ignores the selected sectors
that are protected.
The system can use Q6 and Q2 together to determine
whether a sector is actively erasing or is erase sus-
pended. When the device is actively erasing (that is, the
Automatic Erase algorithm is in progress), Q6 toggling.
When the device enters the Erase Suspend mode, Q6
stops toggling. However, the system must also use Q2
to determine which sectors are erasing or erase-sus-
pended. Alternatively, the system can use Q7.
If a program address falls within a protected sector, Q6
toggles for approximately 2 us after the program com-
mand sequence is written, then returns to reading array
data.
Q6 also toggles during the erase-suspend-program mode,
and stops toggling once the Automatic Program algo-
rithm is complete.
Table 7 shows the outputs for Toggle Bit I on Q6.
Q2:Toggle Bit II
The "Toggle Bit II" on Q2, when used with Q6, indicates
whether a particular sector is actively eraseing (that is,
the Automatic Erase alorithm is in process), or whether
that sector is erase-suspended. Toggle Bit II is valid
after the rising edge of the final WE or CE, whichever
happens first, in the command sequence.
Q2 toggles when the system reads at addresses within
those sectors that have been selected for erasure. (The
system may use either OE or CE to control the read
cycles.) But Q2 cannot distinguish whether the sector
is actively erasing or is erase-suspended. Q6, by com-
parison, indicates whether the device is actively eras-
ing, or is in Erase Suspend, but cannot distinguish which
sectors are selected for erasure. Thus, both status bits
are required for sectors and mode information. Refer to
Table 7 to compare outputs for Q2 and Q6.
Reading Toggle Bits Q6/ Q2
Whenever the system initially begins reading toggle bit
status, it must read Q7-Q0 at least twice in a row to
determine whether a toggle bit is toggling. Typically, the
system would note and store the value of the toggle bit
after the first read. After the second read, the system
would compare the new value of the toggle bit with the
first. If the toggle bit is not toggling, the device has
completed the program or erase operation. The system
can read array data on Q7-Q0 on the following read cycle.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the sys-
tem also should note whether the value of Q5 is high
(see the section on Q5). If it is, the system should then
determine again whether the toggle bit is toggling, since
the toggle bit may have stopped toggling just as Q5 went
high. If the toggle bit is no longer toggling, the device
has successfuly completed the program or erase opera-
tion. If it is still toggling, the device did not complete the
operation successfully, and the system must write the
reset command to return to reading array data.
The remaining scenario is that system initially determines
that the toggle bit is toggling and Q5 has not gone high.
The system may continue to monitor the toggle bit and
Q5 through successive read cycles, determining the sta-
tus as described in the previous paragraph. Alterna-
tively, it may choose to perform other system tasks. In
this case, the system must start at the beginning of the
algorithm when it returns to determine the status of the
operation.
Q5
Exceeded Timing Limits
Q5 will indicate if the program or erase time has ex-
ceeded the specified limits(internal pulse count). Under
these conditions Q5 will produce a "1". This time-out
condition indicates that the program or erase cycle was
not successfully completed. Data Polling and Toggle Bit
are the only operating functions of the device under this
condition.
If this time-out condition occurs during sector erase op-
15
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
eration, it specifies that a particular sector is bad and it
may not be reused. However, other sectors are still func-
tional and may be used for the program or erase opera-
tion. The device must be reset to use other sectors.
Write the Reset command sequence to the device, and
then execute program or erase command sequence. This
allows the system to continue to use the other active
sectors in the device.
If this time-out condition occurs during the chip erase
operation, it specifies that the entire chip is bad or com-
bination of sectors are bad.
Status
Q7
Q6
Q5
Q3
Q2
RY/BY
(Note1)
(Note2)
Byte Program in Auto Program Algorithm
Q7
Toggle
0
N/A
No
0
Toggle
Auto Erase Algorithm
0
Toggle
0
1
Toggle
0
Erase Suspend Read
1
No
0
N/A Toggle
1
(Erase Suspended Sector)
Toggle
In Progress
Erase Suspended Mode
Erase Suspend Read
Data
Data
Data
Data
Data
1
(Non-Erase Suspended Sector)
Erase Suspend Program
Q7
Toggle
0
N/A
N/A
0
Byte Program in Auto Program Algorithm
Q7
Toggle
1
N/A
No
0
Toggle
Exceeded
Time Limits Auto Erase Algorithm
0
Toggle
1
1
Toggle
0
Erase Suspend Program
Q7
Toggle
1
N/A
N/A
0
Table 7. WRITE OPERATION STATUS
Note:
1. Q7 and Q2 require a valid address when reading status information. Refer to the appropriate subsection for further
details.
2. Q5 switches to '1' when an Auto Program or Auto Erase operation has exceeded the maximum timing limits.
See "Q5:Exceeded Timing Limits " for more information.
If this time-out condition occurs during the byte program-
ming operation, it specifies that the entire sector con-
taining that byte is bad and this sector maynot be re-
used, (other sectors are still functional and can be re-
used).
The time-out condition will not appear if a user tries to
program a non blank location without erasing. Please
note that this is not a device failure condition since the
device was incorrectly used.
16
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
POW
ER SUPPLY DECOUPLING
In order to reduce power switching effect, each device
should have a 0.1uF ceramic capacitor connected be-
tween its VCC and GND.
POWER-UP SEQUENCE
The MX29LV081 powers up in the Read only mode. In
addition, the memory contents may only be altered after
successful completion of the predefined command se-
quences.
TEMPORARY SECTOR UNPROTECT
This feature allows temporary unprotection of previously
protected sector to change data in-system. The Tempo-
rary Sector Unprotect mode is activated by setting the
RESET pin to VID(11.5V-12.5V). During this mode, for-
merly protected sectors can be programmed or erased
as un-protected sector. Once VID is remove from the
RESET pin,all the previously protected sectors are pro-
tected again.
Q3
Sector Erase Timer
After the completion of the initial sector erase command
sequence, the sector erase time-out will begin. Q3 will
remain low until the time-out is complete. Data Polling
and Toggle Bit are valid after the initial sector erase com-
mand sequence.
If Data Polling or the Toggle Bit indicates the device has
been written with a valid erase command, Q3 may be
used to determine if the sector erase timer window is
still open. If Q3 is high ("1") the internally controlled
erase cycle has begun; attempts to write subsequent
commands to the device will be ignored until the erase
operation is completed as indicated by Data Polling or
Toggle Bit. If Q3 is low ("0"), the device will accept
additional sector erase commands. To insure the com-
mand has been accepted, the system software should
check the status of Q3 prior to and following each sub-
sequent sector erase command. If Q3 were high on the
second status check, the command may not have been
accepted.
DATA PROTECTION
The MX29LV081 is designed to offer protection against
accidental erasure or programming caused by spurious
system level signals that may exist during power transi-
tion. During power up the device automatically resets
the state machine in the Read mode. In addition, with
its control register architecture, alteration of the memory
contents only occurs after successful completion of spe-
cific command sequences. The device also incorpo-
rates several features to prevent inadvertent write cycles
resulting from VCC power-up and power-down transition
or system noise.
WRITE PULSE "GLITCH" PROTECTION
Noise pulses of less than 5ns(typical) on CE or WE will
not initiate a write cycle.
LOGICAL INHIBIT
Writing is inhibited by holding any one of OE = VIL, CE
= VIH or WE = VIH. To initiate a write cycle CE and WE
must be a logical zero while OE is a logical one.
SECTOR PROTECTION
The MX29LV081 features hardware sector protection.
This feature will disable both program and erase opera-
tions for these sectors protected. To activate this mode,
the programming equipment must force VID on address
pin A9 and OE (suggest VID = 12V). Programming of
the protection circuitry begins on the falling edge of the
WE pulse and is terminated on the rising edge. Please
refer to sector protect algorithm and waveform.
To verify programming of the protection circuitry, the pro-
gramming equipment must force VID on address pin A9
( with CE and OE at VIL and WE at VIH). When A1=VIH,
A0=VIL, A6=VIL, it will produce a logical "1" code at
device output Q0 for a protected sector. Otherwise the
device will produce 00H for the unprotected sector. In
this mode, the addresses,except for A1, are don't care.
Address locations with A1 = VIL are reserved to read
manufacturer and device codes.(Read Silicon ID)
It is also possible to determine if the sector is protected
in the system by writing a Read Silicon ID command.
Performing a read operation with A1=VIH, it will produce
a logical "1" at Q0 for the protected sector.
17
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
CHIP UNPROTECT
The MX29LV081 also features the chip unprotect mode,
so that all sectors are unprotected after chip unprotect is
completed to incorporate any changes in the code. It is
recommended to protect all sectors before activating
chip unprotect mode.
To activate this mode, the programming equipment must
force VID on control pin OE and address pin A9. The CE
pins must be set at VIL. Pins A6 must be set to VIH.
Refer to chip unprotect algorithm and waveform for the
chip unprotect algorithm. The unprotection mechanism
begins on the falling edge of the WE pulse and is
terminated on the rising edge.
It is also possible to determine if the chip is unprotected
in the system by writing the Read Silicon ID command.
Performing a read operation with A1=VIH, it will produce
00H at data outputs(Q0-Q7) for an unprotected sector.
It is noted that all sectors are unprotected after the chip
unprotect algorithm is completed.
18
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
ABSOLUTE MAXIMUM RATINGS
Storage Temperature
Plastic Packages . . . . . . . . . . . . . ..... -65
o
C to +150
o
C
Ambient Temperature
with Power Applied. . . . . . . . . . . . . .... -65
o
C to +125
o
C
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . . . . . . . . -0.5 V to +4.0 V
A9, OE, and
RESET (Note 2) . . . . . . . . . . . ....-0.5 V to +12.5 V
All other pins (Note 1) . . . . . . . -0.5 V to VCC +0.5 V
Output Short Circuit Current (Note 3) . . . . . . 200 mA
Notes:
1. Minimum DC voltage on input or I/O pins is -0.5 V.
During voltage transitions, input or I/O pins may over-
shoot VSS to -2.0 V for periods of up to 20 ns. See
Figure 6. Maximum DC voltage on input or I/O pins is
VCC +0.5 V. During voltage transitions, input or I/O
pins may overshoot to VCC +2.0 V for periods up to
20 ns.
2. Minimum DC input voltage on pins A9, OE, and
RESET is -0.5 V. During voltage transitions, A9, OE,
and RESET may overshoot VSS to -2.0 V for periods
of up to 20 ns. See Figure 6. Maximum DC input volt-
age on pin A9 is +12.5 V which may overshoot to
14.0 V for periods up to 20 ns.
3. No more than one output may be shorted to ground at
a time. Duration of the short circuit should not be
greater than one second.
Stresses above those listed under "Absolute Maximum
Rat-ings" may cause permanent damage to the device.
This is a stress rating only; functional operation of the
device at these or any other conditions above those in-
dicated in the operational sections of this data sheet is
not implied. Exposure of the device to absolute maxi-
mum rating conditions for extended periods may affect
device reliability.
OPERATING RATINGS
Commercial (C) Devices
Ambient Temperature (T
A
). . . . . . . . . . . . 0
C to +70
C
Industrial (I) Devices
Ambient Temperature (T
A
). . . . . . . . . . -40
C to +85
C
V
CC
Supply Voltages
V
CC
for regulated voltage range . . . . . +3.0 V to 3.6 V
V
CC
for full voltage range. . . . . . . . . . . +2.7 V to 3.6 V
Operating ranges define those limits between which the
functionality of the device is guaranteed.
19
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
CAPACITANCE TA = 25
o
C, f = 1.0 MHz
SYMBOL
PARAMETER
MIN.
TYP
MAX.
UNIT
CONDITIONS
CIN1
Input Capacitance
8
pF
VIN = 0V
CIN2
Control Pin Capacitance
12
pF
VIN = 0V
COUT
Output Capacitance
12
pF
VOUT = 0V
NOTES:
1. VIL min. = -1.0V for pulse width is equal to or less than 50 ns.
VIL min. = -2.0V for pulse width is equal to or less than 20 ns.
2. VIH max. = VCC + 1.5V for pulse width is equal to or less than 20 ns
If VIH is over the specified maximum value, read operation cannot be guaranteed.
3. Automatic sleep mode enable the low power mode when addresses remain stable for tACC +30ns.
READ OPERATION
Table 8. DC CHARACTERISTICS TA = 0
o
C TO 70
o
C, VCC = 2.7V to 3.6V
Symbol
PARAMETER
MIN.
TYP
MAX.
UNIT
CONDITIONS
ILI
Input Leakage Current
1
uA
VIN = VSS to VCC
ILIT
A9 Input Leakage Current
35
uA
VCC=VCC max; A9=12.5V
ILO
Output Leakage Current
1
uA
VOUT = VSS to VCC, VCC=VCC max
ICC1
VCC Active Read Current
7
12
mA
CE=VIL, OE=VIH
@5MHz
2
4
mA
@1MHz
ICC2
VCC Active write Current
15
30
mA
CE=VIL, OE=VIH
ICC3
VCC Standby Current
0.2
5
uA
CE; RESET=VCC
0.3V
ICC4
VCC Standby Current
0.2
5
uA
RESET=VSS
0.3V
During Reset
ICC5
Automative sleep mode
0.2
5
uA
VIH=VCC
0.3V;VIL=VSS
0.3V
VIL
Input Low Voltage(Note 1)
-0.5
0.8
V
VIH
Input High Voltage
0.7xVCC
VCC+ 0.3
V
VID
Voltage for Automative
Select and Temporary
11.5
12.5
V
VCC=3.3V
Sector Unprotect
VOL
Output Low Voltage
0.45
V
IOL = 4.0mA, VCC= VCC min
VOH1
Output High Voltage(TTL)
0.85xVCC
IOH = -2mA, VCC=VCC min
VOH2
Output High Voltage
VCC-0.4
IOH = -100uA, VCC min
(CMOS)
VLKO
Low VCC Lock-out
2.3
2.5
V
Voltage
20
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
29LV081-70
29LV081-90
SYMBOL
PARAMETER
MIN.
MAX.
MIN.
MAX.
UNIT
CONDITIONS
tRC
Read Cycle Time (Note 1)
70
90
ns
tACC
Address to Output Delay
70
90
ns
CE=OE=VIL
tCE
CE to Output Delay
70
90
ns
OE=VIL
tOE
OE to Output Delay
30
35
ns
CE=VIL
tDF
OE High to Output Float (Note1)
0
25
0
30
ns
CE=VIL
tOEH
Output Enable
Read
0
0
ns
Hold Time
Toggle and Data Polling
10
10
ns
tOH
Address to Output hold
0
0
ns
CE=OE=VIL
NOTE:
1. Not 100% tested.
2. tDF is defined as the time at which the output achieves the
open circuit condition and data is no longer driven.
TEST CONDITIONS:
Input pulse levels: 0V/3.0V.
Input rise and fall times is equal to or less than 5ns.
Output load: 1 TTL gate + 100pF (Including scope and
jig), for 29LV081-90. 1 TTL gate + 30pF (Including
scope and jig) for 29LV081-70.
Reference levels for measuring timing: 1.5V.
AC CHARACTERISTICS TA = 0
o
C to 70
o
C, VCC = 2.7V~3.6V
Table 9. READ OPERATIONS
21
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
SWITCHING TEST CIRCUITS
SWITCHING TEST WAVEFORMS
TEST POINTS
3.0V
1.5V
1.5V
0V
AC TESTING: Inputs are driven at 3.0V for a logic "1" and 0V for a logic "0".
Input pulse rise and fall times are < 5ns.
OUTPUT
INPUT
DEVICE UNDER
TEST
DIODES=IN3064
OR EQUIVALENT
CL
6.2K ohm
2.7K ohm
+3.3V
CL=100pF Including jig capacitance (30pF for MX29LV081-70)
22
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 1. READ TIMING WAVEFORMS
Addresses
CE
OE
tACC
WE
VIH
VIL
VIH
VIL
VIH
VIL
VIH
VIL
VOH
VOL
VIH
VIL
HIGH Z
HIGH Z
DATA Valid
tOE
tOEH
tDF
tCE
tACC
tRC
Outputs
RESET
tOH
ADD Valid
23
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
AC CHARACTERISTICS TA = 0
o
C to 70
o
C, VCC = 2.7V~3.6V
Table 10. Erase/Program Operations
29LV081-70
29LV081-90
SYMBOL
PARAMETER
MIN.
MAX.
MIN.
MAX.
UNIT
tWC
Write Cycle Time (Note 1)
70
90
ns
tAS
Address Setup Time
0
0
ns
tAH
Address Hold Time
45
45
ns
tDS
Data Setup Time
35
45
ns
tDH
Data Hold Time
0
0
ns
tOES
Output Enable Setup Time
0
0
ns
tGHWL
Read Recovery Time Before Write
0
0
ns
(OE High to WE Low)
tCS
CE Setup Time
0
0
ns
tCH
CE Hold Time
0
0
ns
tWP
Write Pulse Width
35
35
ns
tWPH
Write Pulse Width High
30
30
ns
tWHWH1
Programming Operation (Note 2)
9 (TYP.)
9 (TYP.)
us
tWHWH2
Sector Erase Operation (Note 2)
0.7(TYP.)
0.7(TYP.)
sec
tVCS
VCC Setup Time (Note 1)
50
50
us
tRB
Recovery Time from RY/BY
0
0
ns
tBUSY
Program/Erase Vaild to RY/BY Delay
90
90
ns
NOTES:
1. Not 100% tested.
2. See the "Erase and Programming Performance" section for more information.
24
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
29LV081-70
29LV081-90
SYMBOL
PARAMETER
MIN.
MAX.
MIN.
MAX.
UNIT
tWC
Write Cycle Time (Note 1)
70
70
ns
tAS
Address Setup Time
0
0
ns
tAH
Address Hold Time
45
45
ns
tDS
Data Setup Time
35
45
ns
tDH
Data Hold Time
0
0
ns
tOES
Output Enable Setup Time
0
0
ns
tGHEL
Read Recovery Time Before Write
0
0
ns
tWS
WE Setup Time
0
0
ns
tWH
WE Hold Time
0
0
ns
tCP
CE Pulse Width
35
35
ns
tCPH
CE Pulse Width High
30
30
ns
tWHWH1
Programming Operation(note2)
9Typ.)
9(Typ.)
us
tWHWH2
Sector Erase Operation (note2)
0.7(Typ.)
0.7(Typ.)
sec
NOTE:
1. Not 100% tested.
2. See the "Erase and Programming Performance" section for more information.
AC CHARACTERISTICS TA = 0
o
C to 70
o
C, VCC = 2.7V~3.6V
Table 11. Alternate CE Controlled Erase/Program Operations
25
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 2. COMMAND WRITE TIMING WAVEFORM
Addresses
CE
OE
WE
DIN
tDS
tAH
Data
tDH
tCS
tCH
tCWC
tWPH
tWP
tOES
tAS
VCC
3V
VIH
VIL
VIH
VIL
VIH
VIL
VIH
VIL
VIH
VIL
ADD Valid
26
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
AUTOMATIC PROGRAMMING TIMING WAVEFORM
Figure 3. AUTOMATIC PROGRAMMING TIMING WAVEFORM
One byte data is programmed. Verify in fast algorithm
and additional verification by external control are not re-
quired because these operations are executed automati-
cally by internal control circuit. Programming comple-
tion can be verified by DATA polling and toggle bit checking
after automatic programming starts. Device outputs
DATA during programming and DATA after programming
on Q7.(Q6 is for toggle bit; see toggle bit, DATA polling,
timing waveform)
tWC
Address
OE
CE
A0h
555h
PA
PD
Status
DOUT
PA
PA
NOTES:
1.PA=Program Address, PD=Program Data, DOUT is the true data the program address
tAS
tAH
tGHWL
tCH
tWP
tDS
tDH
tWHWH1
Read Status Data (last two cycle)
Program Command Sequence(last two cycle)
tBUSY
tRB
tCS
tWPH
tVCS
WE
Data
RY/BY
VCC
27
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 4. AUTOMATIC PROGRAMMING ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Program Data/Address
Write Data A0H Address 555H
YES
Verify Word Ok ?
YES
Auto Program Completed
Data Poll
from system
Increment
Address
Last Address ?
No
No
28
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 5.
CE CONTROLLED PROGRAM TIMING WAVEFORM
tWC
tWH
tGHEL
tWHWH1 or 2
tCP
Address
WE
OE
CE
Data
DQ7
PA
Data Polling
DOUT
RESET
RY/BY
NOTES:
1.PA=Program Address, PD=Program Data, DOUT=Data Out, DQ7=complement of data written to device.
2.Figure indicates the last two bus cycles of the command sequence.
tAH
tAS
PA for program
SA for sector erase
555 for chip erase
tRH
tDH
tDS
tWS
A0 for program
55 for erase
tCPH
tBUSY
PD for program
30 for sector erase
10 for chip erase
555 for program
2AA for erase
29
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
All data in chip are erased. External erase verification is
not required because data is verified automatically by
internal control circuit. Erasure completion can be veri-
fied by DATA polling and toggle bit checking after auto-
matic erase starts. Device outputs 0 during erasure
and 1 after erasure on Q7.(Q6 is for toggle bit; see toggle
bit, DATA polling, timing waveform)
Figure 6. AUTOMATIC CHIP ERASE TIMING WAVEFORM
AUTOMATIC CHIP ERASE TIMING WAVEFORM
tWC
Address
OE
CE
55h
2AAh
555h
10h
In
Progress Complete
VA
VA
NOTES:
SA=sector address(for Sector Erase), VA=Valid Address for reading status data(see "Write Operation Status").
tAS
tAH
tGHWL
tCH
tWP
tDS
tDH
tWHWH2
Read Status Data
Erase Command Sequence(last two cycle)
tBUSY
tRB
tCS
tWPH
tVCS
WE
Data
RY/BY
VCC
30
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 7. AUTOMATIC CHIP ERASE ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data AAH Address 555H
Write Data 80H Address 555H
YES
NO
Data=FFh ?
Write Data 10H Address 555H
Write Data 55H Address 2AAH
Data Pall from System
Auto Chip Erase Completed
31
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 8. AUTOMATIC SECTOR ERASE TIMING WAVEFORM
Sector indicated by A13 to A19 are erased. External
erase verify is not required because data are verified
automatically by internal control circuit. Erasure comple-
tion can be verified by DATA polling and toggle bit check-
ing after automatic erase starts. Device outputs 0 dur-
ing erasure and 1 after erasure on Q7.(Q6 is for toggle
bit; see toggle bit, DATA polling, timing waveform)
AUTOMATIC SECTOR ERASE TIMING WAVEFORM
tWC
Address
OE
CE
55h
2AAh
SA
30h
In
Progress Complete
VA
VA
NOTES:
SA=sector address(for Sector Erase), VA=Valid Address for reading status data(see "Write Operation Status").
tAS
tAH
tGHWL
tCH
tWP
tDS
tDH
tWHWH2
Read Status Data
Erase Command Sequence(last two cycle)
tBUSY
tRB
tCS
tWPH
tVCS
WE
Data
RY/BY
VCC
32
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 9. AUTOMATIC SECTOR ERASE ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data AAH Address 555H
Write Data 80H Address 555H
Write Data 30H Sector Address
Write Data 55H Address 2AAH
Data Poll from System
Auto Sector Erase Completed
NO
Last Sector
to Erase
YES
YES
NO
Data=FFh
33
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 10. ERASE SUSPEND/ERASE RESUME FLOWCHART
START
Write Data B0H
Toggle Bit checking Q6
not toggled
ERASE SUSPEND
YES
NO
Write Data 30H
Continue Erase
Reading or
Programming End
Read Array or
Program
Another
Erase Suspend ?
NO
YES
YES
NO
ERASE RESUME
34
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 11. SECTOR PROTECT/UNPROTECT TIMING WAVEFORM
Sector Protect =150us
Sector Unprotect =15ms
1us
VID
VIH
Data
SA, A6
A1, A0
CE
WE
OE
Valid*
Valid*
Status
Valid*
Sector Protect or Sector Unprotect
40h
60h
60h
Verify
RESET
Note: When sector protect, A6=0, A1=1, A0=0. When sector unprotect, A6=1, A1=1, A0=0.
35
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 12. IN-SYSTEM SECTOR PROTECTION ALGORITHM WITH RESET=VID
START
PLSCNT=1
First Write
Cycle=60H
Yes
No
RESET=VID
Wait 1us
Set up sector address
Write 60H to sector address
with A6=0, A1=1, A0=0
Verify sector protect :
write 40H with A6=0,
A1=1, A0=0
Wait 150us
Increment PLSCNT
Read from sector address
Remove VID from RESET
Temporary Sector
Unprotect Mode
Reset PLSCNT=1
Data=01H
Yes
Yes
Yes
No
No
No
?
PLSCNT=25?
Protect another
sector?
Write reset command
Sector protect complete
Device failed
36
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 13. IN-SYSTEM SECTOR UNPROTECTION ALGORITHM WITH RESET=VID
START
PLSCNT=1
First Write
Cycle=60H ?
Yes
No
RESET=VID
Wait 1us
Set up first sector address
Sector unprotect :
write 60H with
A6=1, A1=1, A0=0
Verify sector unprotect
write 40H to sector address
with A6=1, A1=1, A0=0
Wait 50ms
Increment PLSCNT
Read from sector address
with A6=1, A1=1, A0=0
Remove VID from RESET
Temporary Sector
Unprotect Mode
Set up next sector address
All sector
protected?
Yes
Data=00H
Yes
Yes
Yes
No
No
No
No
Protect all sectors
?
PLSCNT=1000?
Last sector
verified?
Write reset command
Sector unprotect complete
Device failed
37
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 14. TIMING WAVEFORM FOR CHIP UNPROTECTION
tOE
Data
OE
WE
12V
Vcc 3V
12V
Vcc 3V
CE
A9
A1
tOESP
tWPP 2
tVLHT
tVLHT
tVLHT
Verify
00H
A6
Sector Address
A18-A12
F0H
Notes: tVLHT (Voltage transition time)=4us min.
tWPP1 (Write pulse width for sector protect)=100ns min.
tWPP2 (Write pulse width for sector unprotect)=100ns min.
tOESP (OE setup time to WE active)=4us min.
38
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 15. CHIP UNPROTECTION ALGORITHM
START
Protect All Sectors
PLSCNT=1
Chip Unprotect
Complete
Data=00H?
Yes
Set OE=A9=VID
CE=VIL,A6=1
Activate WE Pulse
Time Out 50ms
Set OE=CE=VIL
A9=VID,A1=1
Set Up First Sector Addr
All sectors have
been verified?
Remove VID from A9
Write Reset Command
Device Failed
PLSCNT=1000?
No
Increment
PLSCNT
No
Read Data from Device
Yes
Yes
No
Increment
Sector Addr
* It is recommended before unprotect whole chip, all sectors should be protected in advance.
39
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 16. DATA POLLING ALGORITHM
Read Q7~Q0
Add.=VA(1)
Read Q7~Q0
Add.=VA
Start
Q7 = Data ?
Q5 = 1 ?
Q7 = Data ?
FAIL
Pass
No
No
(2)
No
Yes
Yes
Yes
NOTE : 1.VA=Valid address for programming
2.Q7 should be re-checked even Q5="1" because Q7 may change
simultaneously with Q5.
WRITE OPERATION STATUS
40
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 17. TOGGLE BIT ALOGRITHMS
Read Q7-Q0
Read Q7-Q0
Q5= 1?
Read Q7~Q0 Twice
Program/Erase Operation
Not Complete,Write
Reset Command
Program/Erase
operation Complete
Toggle bit Q6=
Toggle?
Toggle Bit Q6 =
Toggle ?
NO
(Note 1)
(Note 1,2)
YES
NO
NO
YES
YES
Note:1.Read toggle bit twice to determine whether or not it is toggling.
2. Recheck toggle bit because it may stop toggling as Q5 change to "1".
Start
41
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 18. Data Polling Timings (During Automatic Algorithms)
RY/BY
NOTES:
VA=Valid address. Figure shows are first status cycle after command sequence, last status read cycle, and array data read cycle.
tDF
tCE
tACC
tRC
tCH
tOE
tOEH
tOH
tBUSY
Address
CE
OE
WE
DQ7
Q0-Q6
Status Data
Status Data
Complement
Complement
Valid Data
True
VA
VA
VA
High Z
High Z
Valid Data
True
42
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 19. Toggle Bit Timings (During Automatic Algorithms)
NOTES:
VA=Valid address; not required for Q6. Figure shows first two status cycle after command sequence, last status read cycle, and
array data read cycle.
tDF
tCE
tACC
tRC
tCH
tOE
tOEH
tBUSY
High Z
tOH
Address
CE
OE
WE
Q6/Q2
RY/BY
Valid Status
(first raed)
Valid Status
(second read)
(stops toggling)
Valid Data
VA
VA
VA
VA
Valid Data
43
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 20. RESET TIMING WAVFORM
Table 11. AC CHARACTERISTICS
Parameter Std
Description
Test Setup
All Speed Options Unit
tREADY1
RESET PIN Low (During Automatic Algorithms)
MAX
20
us
to Read or Write (See Note)
tREADY2
RESET PIN Low (NOT During Automatic
MAX
500
ns
Algorithms) to Read or Write (See Note)
tRP
RESET Pulse Width (During Automatic Algorithms)
MIN
500
ns
tRH
RESET High Time Before Read(See Note)
MIN
50
ns
tRB
RY/BY Recovery Time(to CE, OE go low)
MIN
0
ns
Note:Not 100% tested
tRH
tRB
tReady1
tRP
tRP
tReady2
RY/BY
CE, OE
RESET
Reset Timing NOT during Automatic Algorithms
Reset Timing during Automatic Algorithms
RY/BY
CE, OE
RESET
44
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Table 12. TEMPORARY SECTOR UNPROTECT
Parameter Std.
Description
Test Setup
AllSpeed Options Unit
tVIDR
VID Rise and Fall Time (See Note)
Min
500
ns
tRSP
RESET Setup Time for Temporary Sector Unprotect
Min
4
us
Note:
Not 100% tested
FIgure 21. TEMPORARY SECTOR UNPROTECT TIMING DIAGRAM
Figure 22. Q6 vs Q2 for Erase and Erase Suspend Operations
NOTES:
The system can use OE or CE to toggle Q2/Q6, Q2 toggles only when read at an address within an erase-suspended
WE
Enter Embedded
Erasing
Erase
Suspend
Enter Erase
Suspend Program
Erase
Suspend
Program
Erase Suspend
Read
Erase
Erase
Resume
Erase
Complete
Erase
Q6
Q2
RESET
CE
WE
RY/BY
tVIDR
tVIDR
Program or Erase Command Sequence
12V
0 or Vcc
0 or Vcc
tRSP
45
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 23. TEMPORARY SECTOR UNPROTECT ALGORITHM
Start
RESET = VID (Note 1)
Perform Erase or Program Operation
RESET = VIH
Temporary Sector Unprotect Completed(Note 2)
Operation Completed
2. All previously protected sectors are protected again.
Note : 1. All protected sectors are temporary unprotected.
VID=11.5V~12.5V
46
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
Figure 24. ID CODE READ TIMING WAVEFORM
tACC
tCE
tACC
tOE
tOH
tOH
tDF
DATA OUT
C2H
38H
VID
VIH
VIL
ADD
A9
ADD
A2-A8
A10-A19
CE
OE
WE
ADD
A0
DATA OUT
DATA
Q0-Q7
VCC
A1
3V
VIH
VIL
VIH
VIL
VIH
VIL
VIH
VIL
VIH
VIL
VIH
VIL
VIH
VIL
47
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
MIN.
MAX.
Input Voltage with respect to GND on all pins except I/O pins
-1.0V
12.5V
Input Voltage with respect to GND on all I/O pins
-1.0V
Vcc + 1.0V
Current
-100mA
+100mA
Includes all pins except Vcc. Test conditions: Vcc = 3.0V, one pin at a time.
LIMITS
PARAMETER
MIN.
TYP.(2)
MAX.(3)
UNITS
Sector Erase Time
0.7
15
sec
Chip Erase Time
14
sec
Byte Programming Time
9
300
us
Chip Programming Time
9
27
sec
Erase/Program Cycles
100,000
Cycles
LATCHUP CHARACTERISTICS
ERASE AND PROGRAMMING PERFORMANCE(1)
Note:
1.Not 100% Tested, Excludes external system level over head.
2.Typical values measured at 25
C, 3V.
3.Maximum values measured at 25
C, 2.7V.
48
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
ORDERING INFORMATION
PLASTIC PACKAGE
PART NO.
ACCESS TIME
OPERATING CURRENT
STANDBY CURRENT
PACKAGE
(ns)
MAX.(mA)
MAX.(uA)
MX29LV081TC-70
70
30
5
40 Pin TSOP
MX29LV081TC-90
90
30
5
40 Pin TSOP
MX29LV081TI-70
70
30
5
40 Pin TSOP
MX29LV081TI-90
90
30
5
40 Pin TSOP
49
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
PACKAGE INFORMATION
40-PIN PLASTIC TSOP
50
P/N:PM0717
MX29LV081
REV. 1.0, JUL. 31, 2001
REVISION HISTORY
Revision No. Description
Page
Date
1.0
1.Heading was changed "Advanced Information" into
P1
JUL/31/2001
"PRELIMINARY"
2.Correct mis-typing
P9~11,18,19
21,46,48
3.Change tBUSY spec from 90us to ns
P23
4.Part number was corrected from "MX29LV081T4C" into
48
"MX29LV081TC"
5.Device ID code was corrected. Actually, it's just a mis-typing, the P10,11,46
device code of product is still "38H"
51
MX29LV081
M
ACRONIX
I
NTERNATIONAL
C
O.,
L
TD.
HEADQUARTERS:
TEL:+886-3-578-6688
FAX:+886-3-563-2888
EUROPE OFFICE:
TEL:+32-2-456-8020
FAX:+32-2-456-8021
JAPAN OFFICE:
TEL:+81-44-246-9100
FAX:+81-44-246-9105
SINGAPORE OFFICE:
TEL:+65-348-8385
FAX:+65-348-8096
TAIPEI OFFICE:
TEL:+886-2-2509-3300
FAX:+886-2-2509-2200
M
ACRONIX
A
MERICA,
I
NC.
TEL:+1-408-453-8088
FAX:+1-408-453-8488
CHICAGO OFFICE:
TEL:+1-847-963-1900
FAX:+1-847-963-1909
http : //www.macronix.com
MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice.