DESCRIPTION
s
275ps propagation delay
s
High bandwidth output transitions
s
Internal 75K
input pull-down resistors
s
Available in 8-pin SOIC package
The SY10/100EL05 are 2-input differential AND/NAND
gates. These devices are functionally equivalent to the
E404 devices, with higher performance capabilities. With
propagation delays and output transition times
significantly faster than the E404, the EL05 is ideally
suited for those applications which require the ultimate
in AC performance.
Because a negative 2-input NAND is equivalent to a
2-input OR function with inverted inputs, the differential
inputs and outputs of the device allows the EL05 to also
be used as a 2-input differential OR/NOR gate.
The differential inputs employ clamp circuitry so that,
under open conditions (pulled down to V
EE
), the input to
the AND gate will be HIGH. In this way, if one set of
inputs is open, the gate will remain active to the other
input.
FEATURES
2-INPUT
DIFFERENTIAL
AND/NAND
PIN CONFIGURATION/BLOCK DIAGRAM
Pin
Function
D
0
, D
1
Data Inputs
Q
Data Outputs
SY10EL05
SY100EL05
FINAL
PIN NAMES
1
2
3
4
5
6
7
8
D
0
D
1
V
CC
Q
V
EE
Q
D
0
D
1
1
SOIC
TOP VIEW
Rev.: F
Amendment: /0
Issue Date:
February 2003
2
SY10EL05
SY100EL05
Micrel
T
A
= 40
C
T
A
= 0
C
T
A
= +25
C
T
A
= +85
C
Symbol
Parameter
Min.
Typ.
Max.
Min.
Typ.
Max.
Min.
Typ.
Max.
Min.
Typ.
Max.
Unit
t
PLH
Propagation Delay to
135
260
440
185
275
390
185
275
390
215
305
420
ps
t
PHL
Output D
V
PP
Minimum Input Swing
(1)
150
--
--
150
--
--
150
--
--
150
--
--
mV
V
CMR
Common Mode Range
(2)
(2)
--
0.4
(2)
--
0.4
(2)
--
0.4
(2)
--
0.4
V
t
r
Output Rise/Fall Times Q
100
225
350
100
225
350
100
225
350
100
225
350
ps
t
f
(20% to 80%)
AC ELECTRICAL CHARACTERISTICS
V
EE
= V
EE
(Min.) to V
EE
(Max.); V
CC
= GND
NOTES:
1. Minimum input swing for which AC parameters are guaranteed. The device has a DC gain of
40.
2. The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified
range and the peak-to-peak voltage lies between V
PP
min. and 1V. The lower end of the CMR range is dependent on V
EE
and is equal to V
EE
+ 3.0V.
PRODUCT ORDERING CODE
DC ELECTRICAL CHARACTERISTICS
T
A
= 40
C
T
A
= 0
C
T
A
= +25
C
T
A
= +85
C
Symbol
Parameter
Min.
Typ.
Max.
Min.
Typ.
Max.
Min.
Typ.
Max.
Min.
Typ.
Max.
Unit
I
EE
Power Supply Current
mA
10EL
--
18
22
14
18
22
14
18
22
14
18
22
100EL
--
18
22
14
18
22
14
18
22
16
21
25
V
EE
Power Supply Voltage
V
10EL 4.75
5.2
5.5
4.75
5.2
5.5
4.75
5.2
5.5
4.75
5.2
5.5
100EL 4.20
4.5
5.5
4.20
4.5
5.5
4.20
4.5
5.5
4.20
4.5
5.5
I
IH
Input HIGH Current
--
--
150
--
--
150
--
--
150
--
--
150
A
V
EE
= V
EE
(Min.) to V
EE
(Max.); V
CC
= GND
Ordering
Package
Operating
Marking
Code
Type
Range
Code
SY10EL05ZC
Z8-1
Commercial
HEL05
SY10EL05ZCTR*
Z8-1
Commercial
HEL05
SY100EL05ZC
Z8-1
Commercial
XEL05
SY100EL05ZCTR*
Z8-1
Commercial
XEL05
*Tape and Reel
Note 1.
Recommended for new designs.
Ordering
Package
Operating
Marking
Code
Type
Range
Code
SY10EL05ZI
(1)
Z8-1
Industrial
HEL05
SY10EL05ZITR*
(1)
Z8-1
Industrial
HEL05
SY100EL05ZI
(1)
Z8-1
Industrial
XEL05
SY100EL05ZITR*
(1)
Z8-1
Industrial
XEL05
*Tape and Reel
4
SY10EL05
SY100EL05
Micrel
MICREL, INC.
1849 FORTUNE DRIVE
SAN JOSE, CA 95131
USA
TEL
+ 1 (408) 944-0800
FAX
+ 1 (408) 944-0970
WEB
http://www.micrel.com
The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use.
Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can
reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into
the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's
use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser's own risk and Purchaser agrees to fully indemnify
Micrel for any damages resulting from such use or sale.
2003 Micrel, Incorporated.
PDF 
ZIP