The SY100EL14V is a low skew 1:5 clock distribution

chip designed explicitly for low skew clock distribution
applications. The device can be driven by either a
differential or single-ended ECL or, if positive power
supplies are used, PECL input signal. The EL14V is
suitable for operation in systems operating from 3.3V to
5.0V supplies. If a single-ended input is to be used the
V

output should be connected to the CLK input and

bypassed to ground via a 0.01

F capacitor. The V

output is designed to act as the switching reference for
the input of the EL14V under single-ended input
conditions, as a result this pin can only source/sink up to
0.5mA of current.

The EL14V features a multiplexed clock input to allow

for the distribution of a lower speed scan or test clock
along with the high speed system clock. When LOW (or
left open and pulled LOW by the input pull-down resistor)
the SEL pin will select the differential clock input.

The common enable (EN) is synchronous so that the

outputs will only be enabled/disabled when they are
already in the LOW state. This avoids any chance of
generating a runt clock pulse when the device is enabled/
disabled as can happen with an asynchronous control.
The internal flip flop is clocked on the falling edge of the
input clock, therefore all associated specification limits
are referenced to the negative edge of the clock input.

When both differential inputs are left open, CLK input

will pull down to V

and CLK input will bias around

/2.

Pin

Function

CLK

Differential Clock Inputs

SCLK

Scan Clock Input

Synchronous Enable

SEL

Clock Select Input

Reference Output

0-4

Differential Clock Outputs

TRUTH TABLE

PIN NAMES

FEATURES

DESCRIPTION

PIN CONFIGURATION/BLOCK DIAGRAM

Precision EdgeTM

SY100EL14V

FINAL

CLK

SCLK

SEL

* On next negative transition of CLK or SCLK

EN VCC NC SCLK CLK CLK V

SEL V

D
Q

SOIC

TOP VIEW

3.3V and 5V power supply options

Typical 30ps output-to-output skew

Max. 50ps output-to-output skew

Synchronous enable/disable

Multiplexed clock input

75K

internal input pull-down resistors

Available in 20-pin SOIC package

5V/3.3V 1:5 CLOCK
DISTRIBUTION

Rev.: B

Amendment: /0

Issue Date:

February 2003

Precision Edge is a trademark of Micrel, Inc.

Precision EdgeTM

Precision EdgeTM

SY100EL14V

Micrel

Symbol

Rating

Value

Unit

Power Supply (V

= 0V)

8.0 to 0

VDC

(3)

Input Voltage (V

= 0V)

0 to -6.0

VDC

OUT

Output Current

Continuous

Surge

100

Operating Temperature Range

40 to +85

Operating Range

(1),(2)

5.7 to -3.0

NOTES:

1. Absolute maximum rating, beyond which, device life may be impaired, unless otherwise specified on an individual data sheet.

2. Parametric values specified at:

100EL14V Series:

3.0V to 5.5V.

3. In PECL mode operation, V

(max) = V

ABSOLUTE MAXIMUM RATINGS

(1)

= 40

= 0

= +25

= +85

Symbol

Parameter

Min.

Typ.

Max.

Min.

Typ.

Max.

Min.

Typ.

Max.

Min.

Typ.

Max.

Unit

Output HIGH Voltage

(2)

-1085 -1005

-880

-1025

-955

-880

-1025

-955

-880

-1025

-955

-880

Output LOW Voltage

(2)

-1830 -1695 -1555 -1810 -1705 -1620 -1810 -1705 -1620 -1810 -1705 -1620

OHA

Output HIGH Voltage

(2)

-1095

-1035

OLA

Output LOW Voltage

(2)

-1555

-1610

Input HIGH Voltage

-1165

-880

-1165

-880

-1165

-880

-1165

-880

Input LOW Voltage

-1810

-1475 -1810

-1475

Input LOW Current

(3)

0.5

CLK

-300

Input High Current

150

Power Supply Current

Output Reference

-1.38

-1.26

-1.38

-1.26

-1.38

-1.26

-1.38

-1.26

Voltage

DC ELECTRICAL CHARACTERISTICS

= V

(Min) to V

(Max); V

= GND

(1)

NOTES:

1. This table replaces the three traditionally seen in ECL 100K data books. The same DC parameter values at V

= -4.5V now apply across the full V

range of -3.0V to -5.5V. Outputs are terminated through a 50

resistor to -2.0V except where otherwise specified on the individual data sheets.

2. V

= V

(Max) or V

(Min).

3. V

= V

(Max).

Precision EdgeTM

SY100EL14V

Micrel

PRODUCT ORDERING CODE

Ordering

Package

Operating

Marking

Code

Type

Range

Code

SY100EL14VZC

Z20-1

Commercial

XEL14V

SY100EL14VZCTR*

Z20-1

Commercial

XEL14V

*Tape and Reel

= 40

= 0

= +25

= +85

Symbol

Parameter

Min.

Max.

Min.

Max.

Min.

Typ.

Max.

Min.

Max.

Unit

PLH

Propagation Delay

PHL

CLK to Q (Diff)

520

720

550

750

580

680

780

630

830

CLK to Q (SE)

470

770

500

800

530

680

830

580

880

SCLK to Q

470

770

500

800

530

680

830

580

880

skew

Part-to-Part Skew

(1)

200

Within-Device Skew

Setup Time EN

150

Hold Time EN

200

Minimum Input

CLK

150

Swing

CMR

Common Mode Range

(2)

< 500mV

-2.0

-0.4

-2.1

-0.4

-2.1

-0.4

-2.1

-0.4

500mV

-1.8

-0.4

-1.9

-0.4

-1.9

-0.4

-1.9

-0.4

Output Rise/Fall Times

230

500

230

500

230

360

500

230

500

Q (20% 80%)

AC ELECTRICAL CHARACTERISTICS

= V

(Min) to V

(Max); V

= GND

NOTES:

1. Skews are specified for identical LOW-to-HIGH or HIGH-to-LOW transitions.

2. The V

CMR

range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified

range and the peak-to-peak voltage lies between V

(Min) and 1V. The lower end of the V

CMR

range varies 1:1 with V

. The numbers in the specification

table assume a nominal V

= -3.3V. For PECL operation, the V

CMR

(Min) will be fixed at 3.3V |V

CMR

(Min)|.

Ordering

Package

Operating

Marking

Code

Type

Range

Code

SY100EL14VZI

(1)

Z20-1

Industrial

XEL14V

SY100EL14VZITR*

(1)

Z20-1

Industrial

XEL14V

Note 1.

Recommended for new designs.

Precision EdgeTM

SY100EL14V

Micrel

20 LEAD SOIC .300" WIDE (Z20-1)

Rev. 03

MICREL, INC.

1849 FORTUNE DRIVE

SAN JOSE, CA 95131

USA

TEL

+ 1 (408) 944-0800

FAX

+ 1 (408) 944-0970

WEB

http://www.micrel.com

The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use.

Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.

Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can

reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into
the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's

use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser's own risk and Purchaser agrees to fully indemnify

Micrel for any damages resulting from such use or sale.

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: SY100EL14VZITR

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: SY100EL14VZITR