ChipFind - документация

Электронный компонент: SY100EL16VZITR

Скачать:  PDF   ZIP
DESCRIPTION
FEATURES
5V/3.3V DIFFERENTIAL
RECEIVER
SY10EL16V
SY100EL16V
s
3.3V and 5V power supply options
s
250ps propagation delay
s
High bandwidth output transitions
s
Internal 75K
input pull-down resistors
s
Replaces SY10/100EL16
s
Improved output waveform characteristics
s
Available in 8-pin (3mm) MSOP and SOIC package
The SY10/100EL16V are differential receivers. The
devices are functionally equivalent to the E116 devices,
with higher performance capabilities. With output
transition times significantly faster than the E116, the
EL16V is ideally suited for interfacing with high-frequency
sources.
The EL16V provides a V
BB
output for either single-
ended use or as a DC bias for AC coupling to the device.
The V
BB
pin should be used only as a bias for the EL16V
as its current sink/source capability is limited. Whenever
used, the V
BB
pin should be bypassed to ground via a
0.01
f capacitor.
Under open input conditions (pulled to V
EE
), internal
input clamps will force the Q output LOW.
PIN NAMES
Pin
Function
D
Data Inputs
Q
Data Outputs
V
BB
Reference Voltage Output
MSOP and SOIC
PIN CONFIGURATION/BLOCK DIAGRAM
1
Rev.: G
Amendment: /0
Issue Date:
July 2003
2
SY10EL16V
SY100EL16V
Micrel
Symbol
Rating
Value
Unit
V
CC
Power Supply Voltage (V
EE
= 0)
+6.0 to 0
V
V
EE
Power Supply Voltage (V
CC
= 0)
6.0 to 0
V
V
IN
Input Voltage (V
CC
= 0V, V
IN
not more negative than V
EE
)
6.0 to 0
V
Input Voltage (V
EE
= 0V, V
IN
not more positive than V
CC
)
+6.0 to 0
V
I
OUT
Output Current
Continuous
50
mA
Surge
100
T
A
Operating Temperature Range
40 to +85
C
T
store
Storage Temperature Range
65 to +150
C
JA
Thermal Resistance (Junction-to-Ambient)
Still Air
160
C/W
500lfpm
109
C/W
JC
Thermal Resistance (Junction-to-Case)
39
C/W
ESD
Mil Std. 883 Human Body Model, All Pins
>1.5k
V
Note 1.
Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. This is a stress rating only and functional operation
is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to ABSOLUTE MAXIMUM
RATlNG conditions for extended periods may affect device reliability.
ABSOLUTE MAXIMUM RATINGS
(1)
Note 1.
Parametric values specified at:
10/100EL16V Series:
-3.0V to -5.5V.
Note 2.
specification for packaged product only.
DC ELECTRICAL CHARACTERISTICS
(Note 1, 2)
T
A =
40
C
T
A =
0
C
T
A =
+25
C
T
A =
+85
C
Symbol
Parameter
Min.
Typ.
Max.
Min.
Typ.
Max.
Min.
Typ.
Max.
Min.
Typ.
Max.
Unit
I
EE
Power Supply Current
mA
10EL
--
18
22
9
18
22
9
18
22
9
18
22
100EL
--
18
22
9
18
22
9
18
22
9
21
26
V
BB
Output Reference
V
Voltage
10EL
1.43
--
1.30 1.38
--
1.27
1.35
--
1.25 1.31
--
1.19
100EL
1.38
--
1.26 1.38
--
1.26
1.38
--
1.26 1.38
--
1.26
I
IH
Input HIGH Current
--
--
150
--
--
150
--
--
150
--
--
150
A
V
EE
= V
EE
(Min.) to V
EE
(Max.); V
CC
= GND
3
SY10EL16V
SY100EL16V
Micrel
T
A =
40
C
T
A =
0
C
T
A =
+25
C
T
A =
+85
C
Symbol
Parameter
Min.
Typ.
Max.
Min.
Typ.
Max.
Min.
Typ.
Max.
Min.
Typ.
Max. Unit
t
PLH
Propagation Delay to
ps
t
PHL
Output
D (Diff)
125
250
375
175
250
325
175
250
325
205
280
355
D (SE)
75
250
425
125
250
375
125
250
375
155
280
405
t
skew
Duty Cycle Skew
(2)
(Diff)
--
5
--
--
5
20
--
5
20
--
5
20
ps
V
PP
Minimum Input Swing
(3)
150
--
--
150
--
--
150
--
--
150
--
--
mV
V
CMR
Common Mode Range
(4)
1.3
--
0.4
1.4
--
0.4
1.4
--
0.4
1.4
--
0.4
V
t
r
Output Rise/Fall Times Q
100
225
350
100
225
350
100
225
350
100
225
350
ps
t
f
(20% to 80%)
Note 1.
Parametric values specified at:
10/100EL16V Series:
-3.0V to -5.5V.
Note 2.
Duty cycle skew is the difference between a t
PLH
and t
PHL
propagation delay through a device.
Note 3.
Minimum input swing for which AC parameters are guaranteed. The device has a DC gain of
40.
Note 4.
The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls
within the specified range and the peak-to-peak voltage lies between V
PP
min. and 1V. The lower end of the CMR range varies 1:1 with V
EE.
The numbers in the spec table assume a nominal V
EE
= 3.3V. Note for PECL operation, the V
CMR
(min) will be fixed at 3.3V |V
CMR
(min)|.
Note 5.
Specification for packaged product only.
V
EE
= V
EE
(Min.) to V
EE
(Max.); V
CC
= GND
AC ELECTRICAL CHARACTERISTICS
(Note 1, 5)
PRODUCT ORDERING CODE
Ordering
Package
Operating
Marking
Code
Type
Range
Code
SY10EL16VKCTR
(1)
K8-1
Commercial
XEL16V
SY100EL16VKCTR
(1)
K8-1
Commercial
XEL16V
SY10EL16VZC
Z8-1
Commercial
XEL16V
SY10EL16VZCTR
(1)
Z8-1
Commercial
XEL16V
SY100EL16VZC
Z8-1
Commercial
XEL16V
SY100EL16VZCTR
(1)
Z8-1
Commercial
XEL16V
Note 1.
Tape and Reel.
Note 2.
Recommended for new designs.
Ordering
Package
Operating
Marking
Code
Type
Range
Code
SY10EL16VKITR
(1, 2)
K8-1
Industrial
XEL16V
SY100EL16VKITR
(1, 2)
K8-1
Industrial
XEL16V
SY10EL16VZI
(2)
Z8-1
Industrial
XEL16V
SY10EL16VZITR
(1, 2)
Z8-1
Industrial
XEL16V
SY100EL16VZI
(2)
Z8-1
Industrial
XEL16V
SY100EL16VZITR
(1, 2)
Z8-1
Industrial
XEL16V
Process:
Bipolar
ESD Rating:
Per Mil Std. 883 Human Body Model,
>1.5kV (all pins).
PRODUCT/PROCESS INFORMATION
4
SY10EL16V
SY100EL16V
Micrel
8 LEAD MSOP (K8-1)
Rev. 01
Package Notes:
Note 1.
Package meets Level 1 moisture sensitivity.
5
SY10EL16V
SY100EL16V
Micrel
8 LEAD SOIC(Z8-1)
Rev. 03
MICREL, INC.
1849 FORTUNE DRIVE
SAN JOSE, CA 95131
USA
TEL
+ 1 (408) 944-0800
FAX
+ 1 (408) 944-0970
WEB
http://www.micrel.com
The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use.
Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can
reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into
the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's
use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser's own risk and Purchaser agrees to fully indemnify
Micrel for any damages resulting from such use or sale.
2003 Micrel, Incorporated.
Package Notes:
Note 1.
Package meets Level 1 moisture sensitivity.