MICROPAC INDUSTRIES, INC.
OPTOELECTRONIC PRODUCTS DIVISION 725 E. Walnut St., Garland, TX 75040 (972) 272-3571 Fax (972) 487-6918
www.micropac.com
E-MAIL: optosales@micropac.com
5 - 4
66063
SINGLE-CHANNEL, VERY HIGH SPEED,
LEADLESS CHIP CARRIER OPTOCOPLER
Mii
OPTOELECTRONIC PRODUCTS
DIVISION
Features:
Electrically similar to 6N134
Hermetically sealed 24 Pin LCC
Very high speed
5MHz bandwidth typical
Performance guaranteed over -55C to +125C
ambient temperature range
Standard and high reliability screened parts
available
TTL compatible input and output
High common mode rejection
1000 Vdc isolation test voltage
Leadless chip carrier package
Faraday shield provides high common mode
rejection
DESCRIPTION
The 66063 single channel optocoupler consists of an LED optically coupled to a high speed, high gain inverting
detector gate. Maximum isolation can be achieved while providing TTL output capable of switching with propagation
delays of 55ns typical. The 66063 is a 24 pin hermetically sealed leadless chip carrier and is available in standard and
screened versions or tested to customer specifications.
ABSOLUTE MAXIMUM RATINGS
(No derating required up to 125C)
Storage temperature ........................................................................................................................................... -65C to +150C
Operating temperature......................................................................................................................................... -55C to +125C
Lead solder temperature ....................................................................................................................................260C for 10 sec.
Peak forward input current ........................................................................................................................40 mA (<1ms duration)
Average forward input current ..............................................................................................................................................20mA
Input power dissipation ........................................................................................................................................................35 mW
Reverse input voltage - V
R
..........................................................................................................................................................5V
Supply voltage - V
CC
................................................................................................................................ 7V (1 minute maximum)
Output current - I
O
..................................................................................................................................................................25mA
Output power dissipation ......................................................................................................................................................40mW
Output voltage - V
O
.....................................................................................................................................................................7V
Total power dissipation .......................................................................................................................................................175mW
Package Dimensions Schematic Diagram
NO. 1 LEAD
Mii 66063
XXXXX
K
1
A
2
GND
Vo
Vcc
16
14
15
IDENTIFIER
0.400+.010,-.055
[10.160 +.254,-.127]
REF.
0.020
(.508)
ALL DIMENSIONS ARE IN INCHES [MILLIMETERS]
NOTE:
A .01 TO 0.1 uF BYPASS
CAPACITOR MUST BE
CONNECTED BETWEEN
PINS 15 AND 10
TYP
0.045 [1.13]
0.070 [1.78]
0.050 [1.27]
0.035 [0.89]
R0.008 [R0.20] TYP
MICROPAC INDUSTRIES, INC.
OPTOELECTRONIC PRODUCTS DIVISION 725 E. Walnut St., Garland, TX 75040 (972) 272-3571 Fax (972) 487-6918
www.micropac.com
E-MAIL: optosales@micropac.com
5 - 5
66063
SINGLECHANNEL, VERY HIGH SPEED, LEADLESS CHIP CARRIER OPTOCOUPLER, Continued
ELECTRICAL CHARACTERISTICS
OVER RECOMMENDED TEMPERATURE (T
A
= -55
C to +125C) unless otherwise specified
PARAMETER
SYMBOL
MIN
TYP**
MAX
UNITS
TEST CONDITIONS
NOTE
High Level Output Current
I
OH
5
250
A
V
CC
= 5.5V, V
O
= 5.5V,
I
F
= 250
A
Low Level Output Voltage
V
OL
0.5
0.6
V
V
CC
= 5.5V, I
F
= 10mA,
I
OL
(
Sinking
) = 10mA
6
High Level Supply Current
I
CCH
18
28
mA
V
CC
= 5.5V, I
F
= 0
(
Both Channels
)
Low Level Supply Current
I
CCL
26
36
mA
V
CC
= 5.5V, I
F
= 20mA
(
Both Channels
)
Input Forward Voltage
V
F
1.5
1.75
V
I
F
= 20mA, T
A
= 25C
Input Reverse Breakdown Voltage
BV
R
5
V
I
R
= 10A, T
A
= 25C
Input-Output Insulation Leakage
Current
I
I--O
1.0
A
V
I-0
= 1000Vdc,
Relative Humidity = 45%
T
A
= 25C, t = 5s.
1
Propagation Delay Time To High
Output Level
t
PLH
65
100
ns
R
L
= 510
, C
L
= 15pF,
I
F
= 13mA, T
A
= 25C
2, 6
Propagation Delay Time To Low
Output Level
t
PHL
55
100
ns
R
L
= 510
, C
L
= 15pF,
I
F
= 13mA, T
A
= 25C
3, 6
**All typical values are at VCC
=
5V, TA
= 25
C
TYPICAL CHARACTERISTICS
AT T
A
= 25
C, V
CC
= 5V
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
TEST CONDITIONS
NOTE
Input Capacitance
C
IN
60
pF
V
F
= 0, f = 1MHz
Input Diode Temperature
Coefficient
v
F
T
A
-1.9
mV/
C
I
F
= 20mA
Resistance (Input-Output)
R
I- O
10
12
V
I-O
= 500V
1
Capacitance (Input-Output)
C
I-O
1.7
pF
f = 1MHz
1
Output Rise-Fall Time
(10-90%)
t
r
,
t
f
35
ns
R
L
= 510
, C
L
= 15pF,
I
F
= 13mA
6
Common Mode Transient
Immunity at High Output
CM
H
1000
10000
V/
s
V
CM
= 10V (peak)
V
O
(min.) = 2V,
R
L
= 510
, I
F
= 0mA
4
Common Mode Transient
Immunity at Low Output
CM
L
1000
10000
V/
s
V
CM
= 10V (peak)
V
O
(max.) = 0.8V,
R
L
= 510
, I
F
= 10mA
5
NOTES:
1.
Measured between pins 1 and 2 shorted together, and pins 10, 14 and 15 shorted together.
2. The
t
PHL
propagation delay is measured from the 6.5mA point on the trailing edge of the input pulse to the 1.5V point on the trailing edge of the output
pulse.
3. The
t
PHL
propagation delay is measured from the 6.5mA point on the leading edge of the input pulse to the 1.5V point on the leading edge of the output
pulse.
4. CM
H
is the max. tolerable common mode transient to assure that the output will remain in a high logic state (i.e. V
O
>
2.0V).
5. CM
L
is the max. tolerable common mode transient to assure that the output will remain in a low logic state (i.e. V
O
<
0.8V).
6.
It is essential that a bypass capacitor (.01 to 0.1
F, ceramic) be connected from pin 10 to pin 15.
RECOMMENDED OPERATING CONDITIONS
Parameter
SYMBOL
MIN
MAX
UNITS
Input Current, Low Level Each Channel
I
FL
0
250
A
Input Current, High Level Each Channel
I
FH
12.5
20
mA
Supply Voltage
V
CC
4.5
5.5
V
Fan Out (TTL Load) Each Channel
N
6
Operating Temperature
T
A
-55
+125
C
PDF 
ZIP