MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
1
REV 6
Motorola, Inc. 1995
10/95
Quad 2-Input Data
Selectors/Multiplexers
HighPerformance SiliconGate CMOS
The MC54/74HC157A is identical in pinout to the LS157. The device
inputs are compatible with standard CMOS outputs; with pullup resistors,
they are compatible with LSTTL outputs.
This device routes 2 nibbles (A or B) to a single port (Y) as determined by
the Select input. The data is presented at the outputs in noninverted form. A
high level on the Output Enable input sets all four Y outputs to a low level.
The HC157A is similar in function to the HC257 which has 3state outputs.
Output Drive Capability: 10 LSTTL Loads
Outputs Directly Interface to CMOS, NMOS, and TTL
Operating Voltage Range: 2.0 to 6.0 V
Low Input Current: 1.0
A
High Noise Immunity Characteristic of CMOS Devices
In Compliance with the Requirements Defined by JEDEC Standard
No. 7A
Chip Complexity: 82 FETs or 20.5 Equivalent Gates
LOGIC DIAGRAM
2
5
11
14
3
6
10
13
4
7
9
12
1
15
A0
A1
A2
A3
B0
B1
B2
B3
Y0
Y1
Y2
Y3
SELECT
OUTPUT
ENABLE
DATA
OUTPUTS
NIBBLE
A INPUTS
NIBBLE
B INPUTS
PIN 16 = VCC
PIN 8 = GND
MC54/74HC157A
FUNCTION TABLE
PIN ASSIGNMENT
Inputs
Output
Outputs
Enable
Select
Y0 Y3
X = don't care
A0 A3, B0 B3 = the levels
of the respective DataWord
Inputs.
13
14
15
16
9
10
11
12
5
4
3
2
1
8
7
6
SELECT
Y0
B0
A0
Y1
B1
A1
GND
Y3
B3
A3
OUTPUT
ENABLE
VCC
B2
A2
Y2
H
L
L
X
L
H
L
A0 A3
B0 B3
D SUFFIX
SOIC PACKAGE
CASE 751B05
N SUFFIX
PLASTIC PACKAGE
CASE 64808
ORDERING INFORMATION
MC54HCXXXAJ
MC74HCXXXAN
MC74HCXXXAD
MC74HCXXXADT
Ceramic
Plastic
SOIC
TSSOP
1
16
1
16
1
16
DT SUFFIX
TSSOP PACKAGE
CASE 948F01
J SUFFIX
CERAMIC PACKAGE
CASE 62010
1
16
MC54/74HC157A
MOTOROLA
HighSpeed CMOS Logic Data
DL129 -- Rev 6
2
MAXIMUM RATINGS*
Symbol
Parameter
Value
Unit
VCC
DC Supply Voltage (Referenced to GND)
0.5 to + 7.0
V
Vin
DC Input Voltage (Referenced to GND)
1.5 to VCC + 1.5
V
Vout
DC Output Voltage (Referenced to GND)
0.5 to VCC + 0.5
V
Iin
DC Input Current, per Pin
20
mA
Iout
DC Output Current, per Pin
25
mA
ICC
DC Supply Current, VCC and GND Pins
50
mA
PD
Power Dissipation in Still Air, Plastic or Ceramic DIP
SOIC Package
TSSOP Package
750
500
450
mW
Tstg
Storage Temperature
65 to + 150
_
C
TL
Lead Temperature, 1 mm from Case for 10 Seconds
(Plastic DIP, SOIC or TSSOP Package)
(Ceramic DIP)
260
300
_
C
* Maximum Ratings are those values beyond which damage to the device may occur.
Functional operation should be restricted to the Recommended Operating Conditions.
Derating -- Plastic DIP: 10 mW/
_
C from 65
_
to 125
_
C
Ceramic DIP: 10 mW/
_
C from 100
_
to 125
_
C
SOIC Package: 7 mW/
_
C from 65
_
to 125
_
C
TSSOP Package: 6.1 mW/
_
C from 65
_
to 125
_
C
For high frequency or heavy load considerations, see Chapter 2 of the Motorola HighSpeed CMOS Data Book (DL129/D).
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Min
Max
Unit
VCC
DC Supply Voltage (Referenced to GND)
2.0
6.0
V
Vin, Vout
DC Input Voltage, Output Voltage
(Referenced to GND)
0
VCC
V
TA
Operating Temperature, All Package Types
55
+ 125
_
C
tr, tf
Input Rise and Fall Time
VCC = 2.0 V
(Figure 1)
VCC = 4.5 V
VCC = 6.0 V
0
0
0
1000
500
400
ns
DC ELECTRICAL CHARACTERISTICS
(Voltages Referenced to GND)
Symbol
Parameter
Test Conditions
VCC
V
Guaranteed Limit
Unit
Symbol
Parameter
Test Conditions
VCC
V
55 to
25
_
C
v
85
_
C
v
125
_
C
Unit
VIH
Minimum HighLevel Input
Voltage
Vout = 0.1 V or VCC 0.1 V
|Iout|
v
20
A
2.0
4.5
6.0
1.5
3.15
4.2
1.5
3.15
4.2
1.5
3.15
4.2
V
VIL
Maximum LowLevel Input
Voltage
Vout = 0.1 V or VCC 0.1 V
|Iout|
v
20
A
2.0
4.5
6.0
0.5
1.35
1.8
0.5
1.35
1.8
0.5
1.35
1.8
V
VOH
Minimum HighLevel Output
Voltage
Vin = VIH or VIL
|Iout|
v
20
A
2.0
4.5
6.0
1.9
4.4
5.9
1.9
4.4
5.9
1.9
4.4
5.9
V
Vin = VIH or VIL |Iout|
v
4.0 mA
|Iout|
v
5.2 mA
4.5
6.0
3.98
5.48
3.84
5.34
3.7
5.2
VOL
Maximum LowLevel Output
Voltage
Vin = VIH or VIL
|Iout|
v
20
A
2.0
4.5
6.0
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
V
Vin = VIH or VIL |Iout|
v
4.0 mA
|Iout|
v
5.2 mA
4.5
6.0
0.26
0.26
0.33
0.33
0.4
0.4
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this highimpedance cir-
cuit. For proper operation, Vin and
Vout should be constrained to the
range GND
v
(Vin or Vout)
v
VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or VCC).
Unused outputs must be left open.
MC54/74HC157A
HighSpeed CMOS Logic Data
DL129 -- Rev 6
3
MOTOROLA
DC ELECTRICAL CHARACTERISTICS
(Voltages Referenced to GND)
Unit
Guaranteed Limit
VCC
V
Test Conditions
Parameter
Symbol
Unit
v
125
_
C
v
85
_
C
55 to
25
_
C
VCC
V
Test Conditions
Parameter
Symbol
Iin
Maximum Input Leakage Current
Vin = VCC or GND
6.0
0.1
1.0
1.0
A
ICC
Maximum Quiescent Supply
Current (per Package)
Vin = VCC or GND
Iout = 0
A
6.0
4.0
40
160
A
NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola HighSpeed CMOS Data Book (DL129/D).
AC ELECTRICAL CHARACTERISTICS
(CL = 50 pF, Input tr = tf = 6.0 ns)
Symbol
Parameter
VCC
V
Guaranteed Limit
Unit
Symbol
Parameter
VCC
V
55 to
25
_
C
v
85
_
C
v
125
_
C
Unit
tPLH,
tPHL
Maximum Propagation Delay, Input A or B to Output Y
(Figures 1 and 4)
2.0
4.5
6.0
105
21
18
130
26
22
160
32
27
ns
tPLH,
tPHL
Maximum Propagation Delay, Select to Output Y
(Figures 2 and 4)
2.0
4.5
6.0
110
22
19
140
28
24
165
33
28
ns
tPLH,
tPHL
Maximum Propagation Delay, Output Enable to Output Y
(Figures 3 and 4)
2.0
4.5
6.0
100
20
17
125
25
21
150
30
26
ns
tTLH,
tTHL
Maximum Output Transition Time, Any Output
(Figures 1 and 4)
2.0
4.5
6.0
75
15
13
95
19
16
110
22
19
ns
Cin
Maximum Input Capacitance
--
10
10
10
pF
NOTE: For propagation delays with loads other than 50 pF, and information on typical parametric values, see Chapter 2 of the Motorola High
Speed CMOS Data Book (DL129/D).
CPD
Power Dissipation Capacitance (Per Package)*
Typical @ 25
C, VCC = 5.0 V
pF
CPD
Power Dissipation Capacitance (Per Package)*
33
pF
* Used to determine the noload dynamic power consumption: PD = CPD VCC2f + ICC VCC. For load considerations, see Chapter 2 of the
Motorola HighSpeed CMOS Data Book (DL129/D).
PIN DESCRIPTIONS
INPUTS
A0, A1, A2, A3 (Pins 2, 5, 11, 14)
Nibble A inputs. The data present on these pins is trans-
ferred to the outputs when the Select input is at a low level
and the Output Enable input is at a low level. The data is
presented to the outputs in noninverted form.
B0, B1, B2, B3 (Pins 3, 6, 10, 13)
Nibble B inputs. The data present on these pins is trans-
ferred to the outputs when the Select input is at a high level
and the Output Enable input is at a low level. The data is
presented to the outputs in noninverted form.
OUTPUTS
Y0, Y1, Y2, Y3 (Pins 4, 7, 9, 12)
Data outputs. The selected input Nibble is presented at
these outputs when the Output Enable input is at a low level.
The data present on these pins is in its noninverted form. For
the Output Enable input at a high level, the outputs are at a
low level.
CONTROL INPUTS
Select (Pin 1)
Nibble select. This input determines the data word to be
transferred to the outputs. A low level on this input selects
the A inputs and a high level selects the B inputs.
Output Enable (Pin 15)
Output Enable input. A low level on this input allows the
selected input data to be presented at the outputs. A high
level on this input sets all outputs to a low level.
MC54/74HC157A
MOTOROLA
HighSpeed CMOS Logic Data
DL129 -- Rev 6
4
SWITCHING WAVEFORMS
INPUT A OR B
Figure 1. HC157A
Figure 2. Y versus Select, Noninverted
OUTPUT
ENABLE
tPLH
tPHL
tr
tf
VCC
GND
tTHL
tTLH
10%
50%
90%
10%
50%
90%
Figure 3. HC157A
OUTPUT Y
EXPANDED LOGIC DIAGRAM
4
7
9
12
2
3
5
6
11
10
14
13
15
1
A0
B0
A1
B1
A2
B2
A3
B3
Y0
Y1
Y2
Y3
OUTPUT ENABLE
SELECT
DATA
OUTPUTS
NIBBLE
OUTPUTS
* Includes all probe and jig capacitance
CL*
TEST POINT
DEVICE
UNDER
TEST
OUTPUT
Figure 4. Test Circuit
tr
tf
VCC
GND
OUTPUT Y
tPHL
tPLH
10%
50%
90%
10%
50%
90%
tTLH
tTHL
tr
tf
VCC
GND
SELECT
OUTPUT Y
tPHL
tPLH
tTLH
tTHL
10%
50%
90%
10%
50%
90%
MC54/74HC157A
HighSpeed CMOS Logic Data
DL129 -- Rev 6
5
MOTOROLA
OUTLINE DIMENSIONS
J SUFFIX
CERAMIC PACKAGE
CASE 62010
ISSUE V
N SUFFIX
PLASTIC PACKAGE
CASE 64808
ISSUE R
19.05
6.10
--
0.39
1.40
0.21
3.18
19.93
7.49
5.08
0.50
1.65
0.38
4.31
0
0.51
15
1.01
1.27 BSC
2.54 BSC
7.62 BSC
MIN
MIN
MAX
MAX
INCHES
MILLIMETERS
DIM
0.750
0.240
--
0.015
0.055
0.008
0.125
0.785
0.295
0.200
0.020
0.065
0.015
0.170
0.050 BSC
0.100 BSC
0.300 BSC
A
B
C
D
E
F
G
J
K
L
M
N
0
0.020
15
0.040
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4. DIM F MAY NARROW TO 0.76 (0.030) WHERE
THE LEAD ENTERS THE CERAMIC BODY.
1
8
9
16
A
B
C
K
N
G
E
F
D
16 PL
T
SEATING
PLANE
M
L
J
16 PL
0.25 (0.010)
T
A
M
S
0.25 (0.010)
T
B
M
S
MIN
MIN
MAX
MAX
INCHES
MILLIMETERS
DIM
A
B
C
D
F
G
H
J
K
L
M
S
18.80
6.35
3.69
0.39
1.02
0.21
2.80
7.50
0
0.51
19.55
6.85
4.44
0.53
1.77
0.38
3.30
7.74
10
1.01
0.740
0.250
0.145
0.015
0.040
0.008
0.110
0.295
0
0.020
0.770
0.270
0.175
0.021
0.070
0.015
0.130
0.305
10
0.040
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
2.54 BSC
1.27 BSC
0.100 BSC
0.050 BSC
A
B
1
8
9
16
F
H
G
D
16 PL
S
C
T
SEATING
PLANE
K
J
M
L
T
A
0.25 (0.010)
M
M
0.25 (0.010)
T
B
A
M
S
S
MIN
MIN
MAX
MAX
MILLIMETERS
INCHES
DIM
A
B
C
D
F
G
J
K
M
P
R
9.80
3.80
1.35
0.35
0.40
0.19
0.10
0
5.80
0.25
10.00
4.00
1.75
0.49
1.25
0.25
0.25
7
6.20
0.50
0.386
0.150
0.054
0.014
0.016
0.008
0.004
0
0.229
0.010
0.393
0.157
0.068
0.019
0.049
0.009
0.009
7
0.244
0.019
1.27 BSC
0.050 BSC
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
1
8
9
16
A
B
D
16 PL
K
C
G
T
SEATING
PLANE
R
X 45
M
J
F
P
8 PL
0.25 (0.010)
B
M
M
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751B05
ISSUE J
MC54/74HC157A
MOTOROLA
HighSpeed CMOS Logic Data
DL129 -- Rev 6
6
OUTLINE DIMENSIONS
DT SUFFIX
PLASTIC TSSOP PACKAGE
CASE 948F01
ISSUE O
DIM
MIN
MAX
MIN
MAX
INCHES
MILLIMETERS
A
4.90
5.10
0.193
0.200
B
4.30
4.50
0.169
0.177
C
1.20
0.047
D
0.05
0.15
0.002
0.006
F
0.50
0.75
0.020
0.030
G
0.65 BSC
0.026 BSC
H
0.18
0.28
0.007
0.011
J
0.09
0.20
0.004
0.008
J1
0.09
0.16
0.004
0.006
K
0.19
0.30
0.007
0.012
K1
0.19
0.25
0.007
0.010
L
6.40 BSC
0.252 BSC
M
0
8
0
8
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH.
PROTRUSIONS OR GATE BURRS. MOLD FLASH OR
GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER
SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED
0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE DETERMINED AT
DATUM PLANE W.
_
_
_
_
SECTION NN
SEATING
PLANE
IDENT.
PIN 1
1
8
16
9
DETAIL E
J
J1
B
C
D
A
K
K1
H
G
DETAIL E
F
M
L
2X
L/2
U
S
U
0.15 (0.006) T
S
U
0.15 (0.006) T
S
U
M
0.10 (0.004)
V
S
T
0.10 (0.004)
T
V
W
0.25 (0.010)
16X REF
K
N
N
How to reach us:
USA/EUROPE: Motorola Literature Distribution;
JAPAN: Nippon Motorola Ltd.; TatsumiSPDJLDC, Toshikatsu Otsuki,
P.O. Box 20912; Phoenix, Arizona 85036. 18004412447
6F SeibuButsuryuCenter, 3142 Tatsumi KotoKu, Tokyo 135, Japan. 0335218315
MFAX: RMFAX0@email.sps.mot.com TOUCHTONE (602) 2446609
HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://DesignNET.com
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 85226629298
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different
applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
MC54/74HC157A/D
*MC54/74HC157A/D*
CODELINE
PDF 
ZIP