VCCO Q0

VCCO

SEL

CLK1

CLK2

VEE

S-IN

VCC

VCCO

LOGIC DIAGRAM

S-IN

SEL

CLK1
CLK2

1
0

Pinout: 28-Lead PLCC

(Top View)

* All VCC and VCCO pins are tied together on the die.

MOTOROLA

SEMICONDUCTOR TECHNICAL DATA

REV 2

Motorola, Inc. 1996

12/93

9 Bit Shift Register

The MC10E/100E142 is a 9-bit shift register, designed with byte-parity

applications in mind. The E142 performs serial/parallel in and
serial/parallel out, shifting in one direction. The nine inputs D0 D8
accept parallel input data, while S-IN accepts serial input data. The Qn
outputs do not need to be terminated for the shift operation to function. To
minimize noise and power, any Q output not used should be left
unterminated.

700MHz Min. Shift Frequency

9-Bit for Byte-Parity Applications

Asynchronous Master Reset

Dual Clocks

Extended 100E VEE Range of 4.2V to 5.46V

75k

Input Pulldown Resistors

The SEL (Select) input pin is used to switch between the two modes of

operation -- SHIFT and LOAD. The shift direction is from bit 0 to bit 8.
Input data is accepted by the registers a set-up time before the positive
going edge of CLK1 or CLK2; shifting is also accomplished on the positive
clock edge. A HIGH on the Master Reset pin (MR) asynchronously resets
all the resisters to zero.

PIN NAMES

Pin

Function

D0 D8

Parallel Data Inputs

S-IN

Serial Data Input

SEL

Mode Select Input

CLK1, CLK2

Clock Inputs

Master Reset

Q0 Q8

Data Outputs

FUNCTIONS

SEL

Mode

L
H

Load
Shift

MC10E142

MC100E142

9-BIT SHIFT

REGISTER

FN SUFFIX

PLASTIC PACKAGE

CASE 776-02

MC10E142 MC100E142

MOTOROLA

ECLinPS and ECLinPS Lite

DL140 -- Rev 4

DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)

Symbol

Characteristic

min

typ

max

min

typ

max

min

typ

max

Unit

Condition

IIH

Input HIGH Current

150

IEE

Power Supply Current

10E

120

145

120

145

120

145

100E

120

145

120

145

138

165

AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)

Symbol

Characteristic

min

typ

max

min

typ

max

min

typ

max

Unit

Condition

fSHIFT

Max. Shift Frequency

700

900

700

900

700

900

tPLH

Propagation Delay to Output

tPHL

Clk

600

800

1000

600

800

1000

600

800

1000

600

800

1000

600

800

1000

600

800

1000

Setup Time

100

SEL

300

150

300

150

300

150

Hold Time

300

100

300

100

300

100

SEL

150

tRR

Reset Recovery Time

900

700

900

700

900

700

tPW

Minimum Pulse Width

Clk, MR

400

tSKEW

Within-Device Skew

Note 1

Rise/Fall Times

20 - 80%

300

525

800

300

525

800

300

525

800

1. Within-device skew is defined as identical transitions on similar paths through a device.

MC10E142 MC100E142

MOTOROLA

ECLinPS and ECLinPS Lite
DL140 -- Rev 4

OUTLINE DIMENSIONS

FN SUFFIX

PLASTIC PLCC PACKAGE

CASE 77602

ISSUE D

0.007 (0.180)

T L M

0.007 (0.180)

T L M

0.007 (0.180)

T L M

0.010 (0.250)

T L M

0.007 (0.180)

T L M

0.010 (0.250)

T L M

0.007 (0.180)

T L M

0.007 (0.180)

T L M

0.004 (0.100)

SEATING
PLANE

-T-

12.32
12.32

4.20
2.29
0.33

0.66
0.51
0.64

11.43
11.43

1.07
1.07
1.07

--
2

10.42

1.02

12.57
12.57

4.57
2.79
0.48

0.81

--
--

11.58
11.58

1.21
1.21
1.42
0.50

10.92

1.27 BSC

A
B
C
E

G
H

K
R
U
V

X
Y
Z

G1
K1

MIN

MAX

INCHES

MILLIMETERS

DIM

NOTES:

1. DATUMS -L-, -M-, AND -N- DETERMINED

WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.

2. DIM G1, TRUE POSITION TO BE MEASURED

AT DATUM -T-, SEATING PLANE.

3. DIM R AND U DO NOT INCLUDE MOLD FLASH.

ALLOWABLE MOLD FLASH IS 0.010 (0.250)
PER SIDE.

4. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN

THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR
BURRS, GATE BURRS AND INTERLEAD
FLASH, BUT INCLUDING ANY MISMATCH
BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.

7. DIMENSION H DOES NOT INCLUDE DAMBAR

PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037
(0.940). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMENSION TO BE
SMALLER THAN 0.025 (0.635).

VIEW S

VIEW D-D

VIEW S

0.485
0.485
0.165
0.090
0.013

0.026
0.020
0.025
0.450
0.450
0.042
0.042
0.042

--
2

0.410
0.040

0.495
0.495
0.180

0.110

0.019

0.032

--
--

0.456
0.456
0.048
0.048
0.056
0.020

0.430

0.050 BSC

-N-

Y BRK

-M-

-L-

MC10E142 MC100E142

MOTOROLA

ECLinPS and ECLinPS Lite

DL140 -- Rev 4

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals"
must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.

How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;

JAPAN: Nippon Motorola Ltd.; TatsumiSPDJLDC, 6F SeibuButsuryuCenter,

P.O. Box 20912; Phoenix, Arizona 85036. 18004412447 or 6023035454

3142 Tatsumi KotoKu, Tokyo 135, Japan. 038135218315

MFAX: RMFAX0@email.sps.mot.com TOUCHTONE 6022446609

ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,

INTERNET: http://DesignNET.com

51 Ting Kok Road, Tai Po, N.T., Hong Kong. 85226629298

MC10E142/D

*MC10E142/D*

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: MC10E142FN

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: MC10E142FN