ChipFind - документация

Электронный компонент: K1527A

Скачать:  PDF   ZIP
!
Applications: Phase-Locked Loops (PLL's); Clock
Recovery; Reference Signal Tracking;
Synthesizers; Frequency Modulation/Demodulation
!
2.0 to 33.0 & 51.840MHz Frequency Range
!
Dual Polarity Control Voltage
!
-5.0V to 5.0V Control Voltage
!
20ppm Stability
!
Variety of Deviation Sensitivity Options
!
-40C to 85C Operating Temperature Available
ELECTRICAL SPECIFICATIONS
2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585
800-888-1499 or www.champtech.com
K1527A
33.000
MHZ
CTI DA
TE CODE
6,22 m
m M
ax.
20,8 mm Max.
13,2 mm Max.
PIN 1
1
PART NUMBERING GUIDE
K1527AX X - Specify Frequency
"Blank" = 0C to 70C Operating Temp.
"M" = -40C to +85C Operating Temp.
Model Selection: See Table Above
Frequency Range (MHz)
Input Current (mA)
2 to 33
51.840
<26
Frequency Control Function
Deviation (ppm)
Minimum
Linearity (%)
130
Modulation Bandwidth (3dB)
Nominal Control Voltage (V)
Control Voltage Range (V)
Transfer Function
Input Impedance
< 5
> 30KHz
2.5
-5.0 to +5.0
Positive
> 50K
@ 10KHz
Frequency Stability (ppm)
Overall
-40oC to +85oC
0oC to +70oC
Temperature Range (oC)
Inclusive of Calibration, Temperature, Voltage, Load and Aging
45
20
60
35
Operating
Storage
-40oC to +85oC
-40oC to +125oC
Supply Voltage (V)
Symmetry (%) TTL
Start Up Time (ms)
+5.0V 5%
45/55
<10
Typical SSB Phase Noise (dBC/Hz)
Offset from Carrier
10Hz
-65
100Hz
1KHz
10KHz
100KHz
-95
-120
-140
-150
(For Custom Deviation Range, Vc Range, etc. - Consult Factory)
Model
K1527AA
K1527AC
<50
115
<15
> 20KHz
Deviation Sensitivity (ppm/V)
26 to 40
23 to 35
*K1527AC (Height) = 7.49mm Max
K1527A Series
5V Voltage Controlled Crystal Oscillators
Maximum
200
175
Symmetry (%) CMOS
<33MHz 45/55;
33MHz 40/60
PIN
FUNCTION
Voltage Control
1
7
8
14
Gnd/ & Case Gnd
Output
+ VCC
2553 N. Edgington Street, Franklin Park, IL 60131 " Phone: 847.451.1000 " Fax: 847.451.7585
800-888-1499 or www.champtech.com
2
SHIPPING TUBE CROSS SECTION
OUTPUT WAVEFORM
TEST CIRCUIT DIAGRAM
K1527A Series
5V Voltage Controlled Crystal Oscillators
TEST METHODS
REFERENCE PROCEDURES
DESCRIPTION
Temperature Cycle
MIL-STD-833, Mtd 1010, Cond. B
Mechanical Shock
MIL-STD-883, Mtd 2002, Cond. B
-55C to +125C; Air-to-Air; 100 cycles; 10
min. dwell
Vibration
MIL-STD 883, Mtd 2007, Cond. B
20-2000 Hz; 0.06 inch; 15g's; 3 planes
Humidity Steady State
MIL-STD-202, Mtd 103
40C; 90%-95% R.H.; 56 days
Thermal Shock
MIL-STD-883, Mtd 1011.7 Cond. B
Electrostatic Discharge
Solderability
Hermeticity
Resistance to Soldering
Lead Integrity
Marking Permanence
Life Test
100C to 0C; Water-to-Water; 15 cycles
2 KV to 4 KV Threshold
Solder dip; Meniscograph Criteria
Mass spectro. 2 x 10-8 atmos. CC/sec He
260C; 10 seconds: 1 inch/sec.
Lead tension & bend stress
Resistance to solvents
1500 g's
MIL-STD-883, Mtd 3015 Class II
MIL-STD-883, Mtd 1005.6
MIL-STD-883, Mtd 2022.2
MIL-STD-883, Mtd 1014.8, Cond. A1
MIL-STD-202, Mtd 210D, Cond. C
MIL-STD-883, Mtd 2004.5, Cond. A, B1
MIL-STD-883, Mtd 2015.8
125
C, powered, 1000 hours minimum
MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS