ChipFind - документация

Электронный компонент: MC78L00D

Скачать:  PDF   ZIP
www.docs.chipfind.ru
background image
Semiconductor Components Industries, LLC, 2005
May, 2005 - Rev. 10
1
Publication Order Number:
MC78L00A/D
MC78L00A Series,
NCV78L00A
100 mA Positive Voltage
Regulators
The MC78L00A Series of positive voltage regulators are
inexpensive, easy-to-use devices suitable for a multitude of
applications that require a regulated supply of up to 100 mA. Like
their higher powered MC7800 and MC78M00 Series cousins, these
regulators feature internal current limiting and thermal shutdown
making them remarkably rugged. No external components are
required with the MC78L00 devices in many applications.
These devices offer a substantial performance advantage over the
traditional zener diode-resistor combination, as output impedance
and quiescent current are substantially reduced.
Features
Wide Range of Available, Fixed Output Voltages
Low Cost
Internal Short Circuit Current Limiting
Internal Thermal Overload Protection
No External Components Required
Complementary Negative Regulators Offered (MC79L00A Series)
Pb-Free Packages are Available
NCV Prefix for Automotive and Other Applications Requiring Site
and Control Changes
Figure 1. Representative Schematic Diagram
15k
Q1
Q3
Q5
Input
Output
Ground
Q11
Q12
3.0
0-25k
2.85k
5.0k
Q10
3.8k
Q4
Q6
1.2k
1.9k
19k
2.2k
Q9
Q8
C
Q7
1.0k
420
Z1
Q2
Figure 2. Standard Application
A common ground is required between the input and the output voltages. The
input voltage must remain typically 2.0 V above the output voltage even during
the low point on the input ripple voltage.
* C
in
is required if regulator is located an appreciable distance from power
supply filter.
** C
O
is not needed for stability; however, it does improve transient response.
MC78LXXA
Input
C
in
*
0.33
mF
C
O
**
Output
TO-92
P SUFFIX
CASE 029
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
ORDERING INFORMATION
3
Pin: 1. Output
2. Ground
3. Input
PIN CONNECTIONS
1
8
7
6
5
2
3
4
(Top View)
V
OUT
GND
GND
V
IN
GND
NC
GND
NC
SOIC-8*
D SUFFIX
CASE 751
*SOIC-8 is an internally modified SO-8 package. Pins
2, 3, 6, and 7 are electrically common to the die attach
flag. This internal lead frame modification decreases
package thermal resistance and increases power
dissipation capability when appropriately mounted on
a printed circuit board. SOIC-8 conforms to all exter-
nal dimensions of the standard SO-8 package.
See general marking information in the device marking
section on page 14 of this data sheet.
DEVICE MARKING INFORMATION
2
1
1
8
http://onsemi.com
background image
MC78L00A Series, NCV78L00A
http://onsemi.com
2
MAXIMUM RATINGS
(T
A
= +125
C, unless otherwise noted.)
Rating
Symbol
Value
Unit
Input Voltage (2.6 V-8.0 V)
Input Voltage
(12 V-18 V)
Input Voltage
(24 V)
V
I
30
35
40
Vdc
Storage Temperature Range
T
stg
-65 to +150
C
Operating Junction Temperature Range
T
J
0 to +150
C
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values
(not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage
may occur and reliability may be affected.
ELECTRICAL CHARACTERISTICS
(V
I
= 10 V, I
O
= 40 mA, C
I
= 0.33
m
F, C
O
= 0.1
m
F, - 40
C < T
J
< +125
C (for MC78LXXAB,
NCV78L05A), 0
C < T
J
< +125
C (for MC78LXXAC), unless otherwise noted.)
MC78L05AC, AB, NCV78L05A
Characteristics
Symbol
Min
Typ
Max
Unit
Output Voltage (T
J
= +25
C)
V
O
4.8
5.0
5.2
Vdc
Line Regulation
(T
J
= +25
C, I
O
= 40 mA)
7.0 Vdc
V
I
20 Vdc
8.0 Vdc
V
I
20 Vdc
Reg
line
-
-
55
45
150
100
mV
Load Regulation
(T
J
= +25
C, 1.0 mA
I
O
100 mA)
(T
J
= +25
C, 1.0 mA
I
O
40 mA)
Reg
load
-
-
11
5.0
60
30
mV
Output Voltage
(7.0 Vdc
V
I
20 Vdc, 1.0 mA
I
O
40 mA)
(V
I
= 10 V, 1.0 mA
I
O
70 mA)
V
O
4.75
4.75
-
-
5.25
5.25
Vdc
Input Bias Current
(T
J
= +25
C)
(T
J
= +125
C)
I
IB
-
-
3.8
-
6.0
5.5
mA
Input Bias Current Change
(8.0 Vdc
V
I
20 Vdc)
(1.0 mA
I
O
40 mA)
D
I
IB
-
-
-
-
1.5
0.1
mA
Output Noise Voltage
(T
A
= +25
C, 10 Hz
f
100 kHz)
V
n
-
40
-
m
V
Ripple Rejection (I
O
= 40 mA,
f = 120 Hz, 8.0 Vdc
V
I
18 V, T
J
= +25
C)
RR
41
49
-
dB
Dropout Voltage (T
J
= +25
C)
V
I
- V
O
-
1.7
-
Vdc
NOTE:
NCV78L05A: T
low
= -40
C, T
high
= +125
C. Guaranteed by design. NCV prefix is for automotive and other applications requiring
site and change control.
background image
MC78L00A Series, NCV78L00A
http://onsemi.com
3
ELECTRICAL CHARACTERISTICS
(V
I
= 14 V, I
O
= 40 mA, C
I
= 0.33
m
F, C
O
= 0.1
m
F, - 40
C < T
J
< +125
C (for MC78LXXAB),
0
C < T
J
< +125
C (for MC78LXXAC), unless otherwise noted.)
MC78L08AC, AB
Characteristics
Symbol
Min
Typ
Max
Unit
Output Voltage (T
J
= +25
C)
V
O
7.7
8.0
8.3
Vdc
Line Regulation
(T
J
= +25
C, I
O
= 40 mA)
10.5 Vdc
V
I
23 Vdc
11 Vdc
V
I
23 Vdc
Reg
line
-
-
20
12
175
125
mV
Load Regulation
(T
J
= +25
C, 1.0 mA
I
O
100 mA)
(T
J
= +25
C, 1.0 mA
I
O
40 mA)
Reg
load
-
-
15
8.0
80
40
mV
Output Voltage
(10.5 Vdc
V
I
23 Vdc, 1.0 mA
I
O
40 mA)
(V
I
= 14 V, 1.0 mA
I
O
70 mA)
V
O
7.6
7.6
-
-
8.4
8.4
Vdc
Input Bias Current
(T
J
= +25
C)
(T
J
= +125
C)
I
IB
-
-
3.0
-
6.0
5.5
mA
Input Bias Current Change
(11 Vdc
V
I
23 Vdc)
(1.0 mA
I
O
40 mA)
D
I
IB
-
-
-
-
1.5
0.1
mA
Output Noise Voltage
(T
A
= +25
C, 10 Hz
f
100 kHz)
V
n
-
60
-
m
V
Ripple Rejection (I
O
= 40 mA,
f = 120 Hz, 12 V
V
I
23 V, T
J
= +25
C)
RR
37
57
-
dB
Dropout Voltage (T
J
= +25
C)
V
I
- V
O
-
1.7
-
Vdc
ELECTRICAL CHARACTERISTICS
(V
I
= 15 V, I
O
= 40 mA, C
I
= 0.33
m
F, C
O
= 0.1
m
F, - 40
C < T
J
< +125
C (for MC78LXXAB),
0
C < T
J
< +125
C (for MC78LXXAC), unless otherwise noted.)
MC78L09AC, AB
Characteristics
Symbol
Min
Typ
Max
Unit
Output Voltage (T
J
= +25
C)
V
O
8.6
9.0
9.4
Vdc
Line Regulation
(T
J
= +25
C, I
O
= 40 mA)
11.5 Vdc
V
I
24 Vdc
12 Vdc
V
I
24 Vdc
Reg
line
-
-
20
12
175
125
mV
Load Regulation
(T
J
= +25
C, 1.0 mA
I
O
100 mA)
(T
J
= +25
C, 1.0 mA
I
O
40 mA)
Reg
load
-
-
15
8.0
90
40
mV
Output Voltage
(11.5 Vdc
V
I
24 Vdc, 1.0 mA
I
O
40 mA)
(V
I
= 15 V, 1.0 mA
I
O
70 mA)
V
O
8.5
8.5
-
-
9.5
9.5
Vdc
Input Bias Current
(T
J
= +25
C)
(T
J
= +125
C)
I
IB
-
-
3.0
-
6.0
5.5
mA
Input Bias Current Change
(11 Vdc
V
I
23 Vdc)
(1.0 mA
I
O
40 mA)
D
I
IB
-
-
-
-
1.5
0.1
mA
Output Noise Voltage
(T
A
= +25
C, 10 Hz
f
100 kHz)
V
n
-
60
-
m
V
Ripple Rejection (I
O
= 40 mA,
f = 120 Hz, 13 V
V
I
24 V, T
J
= +25
C)
RR
37
57
-
dB
Dropout Voltage
(T
J
= +25
C)
V
I
- V
O
-
1.7
-
Vdc
background image
MC78L00A Series, NCV78L00A
http://onsemi.com
4
ELECTRICAL CHARACTERISTICS
(V
I
= 19 V, I
O
= 40 mA, C
I
= 0.33
m
F, C
O
= 0.1
m
F, - 40
C < T
J
< +125
C (for MC78LXXAB),
0
C < T
J
< +125
C (for MC78LXXAC), unless otherwise noted.)
MC78L12AC, AB
Characteristics
Symbol
Min
Typ
Max
Unit
Output Voltage (T
J
= +25
C)
V
O
11.5
12
12.5
Vdc
Line Regulation
(T
J
= +25
C, I
O
= 40 mA)
14.5 Vdc
V
I
27 Vdc
16 Vdc
V
I
27 Vdc
Reg
line
-
-
120
100
250
200
mV
Load Regulation
(T
J
= +25
C, 1.0 mA
I
O
100 mA)
(T
J
= +25
C, 1.0 mA
I
O
40 mA)
Reg
load
-
-
20
10
100
50
mV
Output Voltage
(14.5 Vdc
V
I
27 Vdc, 1.0 mA
I
O
40 mA)
(V
I
= 19 V, 1.0 mA
I
O
70 mA)
V
O
11.4
11.4
-
-
12.6
12.6
Vdc
Input Bias Current
(T
J
= +25
C)
(T
J
= +125
C)
I
IB
-
-
4.2
-
6.5
6.0
mA
Input Bias Current Change
(16 Vdc
V
I
27 Vdc)
(1.0 mA
I
O
40 mA)
D
I
IB
-
-
-
-
1.5
0.1
mA
Output Noise Voltage
(T
A
= +25
C, 10 Hz
f
100 kHz)
V
n
-
80
-
m
V
Ripple Rejection (I
O
= 40 mA,
f = 120 Hz, 15 V
V
I
25 V, T
J
= +25
C)
RR
37
42
-
dB
Dropout Voltage
(T
J
= +25
C)
V
I
- V
O
-
1.7
-
Vdc
ELECTRICAL CHARACTERISTICS
(V
I
= 23 V, I
O
= 40 mA, C
I
= 0.33
m
F, C
O
= 0.1
m
F, - 40
C < T
J
< +125
C (for MC78LXXAB),
S
0
C < T
J
< +125
C (for MC78LXXAC), unless otherwise noted.)
MC78L15AC, AB
Characteristics
Symbol
Min
Typ
Max
Unit
Output Voltage (T
J
= +25
C)
V
O
14.4
15
15.6
Vdc
Line Regulation
(T
J
= +25
C, I
O
= 40 mA)
17.5 Vdc
V
I
30 Vdc
20 Vdc
V
I
30 Vdc
Reg
line
-
-
130
110
300
250
mV
Load Regulation
(T
J
= +25
C, 1.0 mA
I
O
100 mA)
(T
J
= +25
C, 1.0 mA
I
O
40 mA)
Reg
load
-
-
25
12
150
75
mV
Output Voltage
(17.5 Vdc
V
I
30 Vdc, 1.0 mA
I
O
40 mA)
(V
I
= 23 V, 1.0 mA
I
O
70 mA)
V
O
14.25
14.25
-
-
15.75
15.75
Vdc
Input Bias Current
(T
J
= +25
C)
(T
J
= +125
C)
I
IB
-
-
4.4
-
6.5
6.0
mA
Input Bias Current Change
(20 Vdc
V
I
30 Vdc)
(1.0 mA
I
O
40 mA)
D
I
IB
-
-
-
-
1.5
0.1
mA
Output Noise Voltage
(T
A
= +25
C, 10 Hz
f
100 kHz)
V
n
-
90
-
m
V
Ripple Rejection (I
O
= 40 mA,
f = 120 Hz, 18.5 V
V
I
28.5 V, T
J
= +25
C)
RR
34
39
-
dB
Dropout Voltage
(T
J
= +25
C)
V
I
- V
O
-
1.7
-
Vdc
background image
MC78L00A Series, NCV78L00A
http://onsemi.com
5
ELECTRICAL CHARACTERISTICS
(V
I
= 27 V, I
O
= 40 mA, C
I
= 0.33
m
F, C
O
= 0.1
m
F, 0
C < T
J
< +125
C, unless otherwise noted.)
MC78L18AC
Characteristics
Symbol
Min
Typ
Max
Unit
Output Voltage (T
J
= +25
C)
V
O
17.3
18
18.7
Vdc
Line Regulation
(T
J
= +25
C, I
O
= 40 mA)
21.4 Vdc
V
I
33 Vdc
20.7 Vdc
V
I
33 Vdc
22 Vdc
V
I
33 Vdc
21 Vdc
V
I
33 Vdc
Reg
line
-
-
45
35
325
275
mV
Load Regulation
(T
J
= +25
C, 1.0 mA
I
O
100 mA)
(T
J
= +25
C, 1.0 mA
I
O
40 mA)
Reg
load
-
-
30
15
170
85
mV
Output Voltage
(21.4 Vdc
V
I
33 Vdc, 1.0 mA
I
O
40 mA)
(20.7 Vdc
V
I
33 Vdc, 1.0 mA
I
O
40 mA)
(V
I
= 27 V, 1.0 mA
I
O
70 mA)
(V
I
= 27 V, 1.0 mA
I
O
70 mA)
V
O
17.1
17.1
-
-
18.9
18.9
Vdc
Input Bias Current
(T
J
= +25
C)
(T
J
= +125
C)
I
IB
-
-
3.1
-
6.5
6.0
mA
Input Bias Current Change
(22 Vdc
V
I
33 Vdc)
(21 Vdc
V
I
33 Vdc)
(1.0 mA
I
O
40 mA)
D
I
IB
-
-
-
-
1.5
0.1
mA
Output Noise Voltage
(T
A
= +25
C, 10 Hz
f
100 kHz)
V
n
-
150
-
m
V
Ripple Rejection (I
O
= 40 mA,
f = 120 Hz, 23 V
V
I
33 V, T
J
= +25
C)
RR
33
48
-
dB
Dropout Voltage
(T
J
= +25
C)
V
I
- V
O
-
1.7
-
Vdc
background image
MC78L00A Series, NCV78L00A
http://onsemi.com
6
ELECTRICAL CHARACTERISTICS
(V
I
= 33 V, I
O
= 40 mA, C
I
= 0.33
m
F, C
O
= 0.1
m
F, 0
C < T
J
< +125
C, unless otherwise noted.)
MC78L24AC
Characteristics
Symbol
Min
Typ
Max
Unit
Output Voltage (T
J
= +25
C)
V
O
23
24
25
Vdc
Line Regulation
(T
J
= +25
C, I
O
= 40 mA)
27.5 Vdc
V
I
38 Vdc
28 Vdc
V
I
80 Vdc
27 Vdc
V
I
38 Vdc
Reg
line
-
-
-
-
50
60
-
300
350
mV
Load Regulation
(T
J
= +25
C, 1.0 mA
I
O
100 mA)
(T
J
= +25
C, 1.0 mA
I
O
40 mA)
Reg
load
-
-
40
20
200
100
mV
Output Voltage
(28 Vdc
V
I
38 Vdc, 1.0 mA
I
O
40 mA)
(27 Vdc
V
I
38 Vdc, 1.0 mA
I
O
40 mA)
(28 Vdc
V
I =
33 Vdc, 1.0 mA
I
O
70 mA)
(27 Vdc
V
I
33 Vdc, 1.0 mA
I
O
70 mA)
V
O
22.8
22.8
-
-
25.2
25.2
Vdc
Input Bias Current
(T
J
= +25
C)
(T
J
= +125
C)
I
IB
-
-
3.1
-
6.5
6.0
mA
Input Bias Current Change
(28 Vdc
V
I
38 Vdc)
(1.0 mA
I
O
40 mA)
D
I
IB
-
-
-
-
1.5
0.1
mA
Output Noise Voltage
(T
A
= +25
C, 10 Hz
f
100 kHz)
V
n
-
200
-
m
V
Ripple Rejection (I
O
= 40 mA,
f = 120 Hz, 29 V
V
I
35 V, T
J
= +25
C)
RR
31
45
-
dB
Dropout Voltage
(T
J
= +25
C)
V
I
- V
O
-
1.7
-
Vdc
background image
MC78L00A Series, NCV78L00A
http://onsemi.com
7
P
D
, POWER DISSIP
A
TION (mW)
I IB
, INPUT BIAS CURRENT (mA)
I IB
, INPUT BIAS CURRENT (mA)
V
O
, OUTPUT VOL
T
AGE (V)
Figure 3. Dropout Characteristics
Figure 4. Dropout Voltage versus
Junction Temperature
Figure 5. Input Bias Current versus
Ambient Temperature
Figure 6. Input Bias Current
versus Input Voltage
Figure 7. Maximum Average Power Dissipation versus
Ambient Temperature - TO-92 Type Package
V
I
, INPUT VOLTAGE (V)
0
2.0
4.0
6.0
8.0
10
, INPUT/OUTPUT DIFFERENTIAL
VOL
T
AGE (V)
IO
T
J
, JUNCTION TEMPERATURE (
C)
0
25
50
75
100
125
-V
V
Dropout of Regulation is
defined as when
V
O
= 2% of V
O
T
A
, AMBIENT TEMPERATURE (
C)
0
25
50
75
100
125
V
I
, INPUT VOLTAGE (V)
0
5.0
10
15
20
25
30
35
40
T
A
, AMBIENT TEMPERATURE (
C)
25
50
75
100
125
150
No Heatsink
8.0
6.0
4.0
2.0
0
2.5
2.0
1.5
1.0
0.5
0
4.2
4.0
3.8
3.6
3.4
3.2
3.0
0
5.0
4.0
3.0
2.0
1.0
0
10,000
1000
100
10
MC78L05AC
V
out
= 5.0 V
T
J
= 25
C
MC78L05AC
V
out
= 5.0 V
I
O
= 40 mA
T
J
= 25
C
R
qJA
= 200
C/W
P
D(max)
to 25
C = 625 mW
I
O
= 1.0 mA
I
O
= 40 mA
I
O
= 100 mA
I
O
= 70 mA
I
O
= 1.0 mA
I
O
= 40 mA
MC78L05AC
V
I
= 10 V
V
O
= 5.0 V
I
O
= 40 mA
30
50
70
90
110
130
150
0.4
0.8
1.2
1.6
2.0
2.4
2.8
0
20
30
50
40
10
L, LENGTH OF COPPER (mm)
170
3.2
R
qJA
P
D
R
,
THERMAL
RESIST
ANCE
JA
JUNCTION-TO-AIR ( C/W)
, MAXIMUM POWER DISSIP
A
TION (W)
2.0 oz.
Copper
Graph represents symmetrical layout
3.0 mm
L
L
Figure 8. SOIC-8 Thermal Resistance and Maximum
Power Dissipation versus P.C.B. Copper Length
P
D(max)
for T
A
= 50
C
background image
MC78L00A Series, NCV78L00A
http://onsemi.com
8
APPLICATIONS INFORMATION
Design Considerations
The MC78L00A Series of fixed voltage regulators are
designed with Thermal Overload Protection that shuts
down the circuit when subjected to an excessive power
overload condition. Internal Short Circuit Protection limits
the maximum current the circuit will pass.
In many low current applications, compensation
capacitors are not required. However, it is recommended
that the regulator input be bypassed with a capacitor if the
regulator is connected to the power supply filter with long
wire lengths, or if the output load capacitance is large. The
input bypass capacitor should be selected to provide good
high-frequency characteristics to insure stable operation
under all load conditions. A 0.33
mF or larger tantalum,
mylar, or other capacitor having low internal impedance at
high frequencies should be chosen. The bypass capacitor
should be mounted with the shortest possible leads directly
across the regulators input terminals. Good construction
techniques should be used to minimize ground loops and
lead resistance drops since the regulator has no external
sense lead. Bypassing the output is also recommended.
Figure 9. Current Regulator
Figure 10.
15 V Tracking Voltage Regulator
The MC78L00 regulators can also be used as a current source
when connected as above. In order to minimize dissipation the
MC78L05C is chosen in this application. Resistor R determines
the current as follows:
For example, a 100 mA current source would require R to be a
50
W, 1/2 W resistor and the output voltage compliance would be
the input voltage less 7 V.
I
O
=
5.0 V
+ I
B
I
IB
= 3.8 mA over line and load changes
Input
0.33
mF
R
I
O
MC78L05A
Constant
Current to
Grounded Load
-
+
MC1741
+20V
0.33
mF
MC78L15A
+V
O
10k
10k
-V
O
7
6
2
3
4
6.5
20V
MPS A70
MPS U55
0.33
mF
0.33
mF
+V
I
-V
I
MC78LXXA
MC79LXXA
+V
O
-V
O
0.33
mF
0.1
mF
0.1
mF
R
Figure 11. Positive and Negative Regulator
background image
MC78L00A Series, NCV78L00A
http://onsemi.com
9
ORDERING INFORMATION
Device
Output Voltage
Operating
Temperature Range
Package
Shipping
MC78L05ABD
SOIC-8
98 Units/Rail
MC78L05ABDG
SOIC-8
98 Units/Rail
MC78L05ABDR2
SOIC-8
2500 Tape & Reel
MC78L05ABDR2G
SOIC-8
(Pb-Free)
2500 Tape & Reel
NCV78L05ABDR2*
SOIC-8
2500 Tape & Reel
NCV78L05ABDR2G*
SOIC-8
(Pb-Free)
2500 Tape & Reel
MC78L05ABP
TO-92
2000 Units/Bag
MC78L05ABPG
T
J
= -40
to +125
C
TO-92
(Pb-Free)
2000 Units/Bag
MC78L05ABPRA
TO-92
2000 Tape & Reel
MC78L05ABPRAG
TO-92
(Pb-Free)
2000 Tape & Reel
MC78L05ABPRE
TO-92
2000 Tape & Reel
MC78L05ABPREG
TO-92
(Pb-Free)
2000 Tape & Reel
MC78L05ABPRM
TO-92
2000 Ammo Pack
MC78L05ABPRMG
TO-92
(Pb-Free)
2000 Ammo Pack
MC78L05ACD
5.0 V
SOIC-8
98 Units/Rail
MC78L05ACDG
SOIC-8
(Pb-Free)
98 Units/Rail
MC78L05ACDR2
SOIC-8
2500 Tape & Reel
MC78L05ACDR2G
SOIC-8
(Pb-Free)
2500 Tape & Reel
MC78L05ACP
TO-92
2000 Units/Bag
MC78L05ACPG
TO-92
(Pb-Free)
2000 Units/Bag
MC78L05ACPRA
TO-92
2000 Tape & Reel
MC78L05ACPRAG
T
J
= 0
to +125
C
TO-92
(Pb-Free)
2000 Tape & Reel
MC78L05ACPRE
TO-92
2000 Tape & Reel
MC78L05ACPREG
TO-92
(Pb-Free)
2000 Tape & Reel
MC78L05ACPRM
TO-92
2000 Ammo Pack
MC78L05ACPRMG
TO-92
(Pb-Free)
2000 Ammo Pack
MC78L05ACPRP
TO-92
2000 Ammo Pack
MC78L05ACPRPG
TO-92
(Pb-Free)
2000 Ammo Pack
*NCV78L05A: T
low
= -40
C, T
high
= +125
C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control.
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
background image
MC78L00A Series, NCV78L00A
http://onsemi.com
10
ORDERING INFORMATION (continued)
Device
Output Voltage
Operating
Temperature Range
Package
Shipping
MC78L08ABD
SOIC-8
98 Units/Rail
MC78L08ABDG
SOIC-8
(Pb-Free)
98 Units/Rail
MC78L08ABDR2
SOIC-8
2500 Tape & Reel
MC78L08ABDR2G
SOIC-8
(Pb-Free)
2500 Tape & Reel
MC78L08ABP
TO-92
2000 Units/Bag
MC78L08ABPG
T
J
= -40
to +125
C
TO-92
(Pb-Free)
2000 Units/Bag
MC78L08ABPRA
TO-92
2000 Tape & Reel
MC78L08ABPRAG
TO-92
(Pb-Free)
2000 Tape & Reel
MC78L08ABPRP
TO-92
2000 Ammo Pack
MC78L08ABPRPG
TO-92
(Pb-Free)
2000 Ammo Pack
MC78L08ACD
SOIC-8
98 Units/Rail
MC78L08ACDG
8.0 V
SOIC-8
(Pb-Free)
98 Units/Rail
MC78L08ACDR2
SOIC-8
2500 Tape & Reel
MC78L08ACDR2G
SOIC-8
(Pb-Free)
2500 Tape & Reel
MC78L08ACP
TO-92
2000 Units/Bag
MC78L08ACPG
T
J
= 0
to +125
C
TO-92
(Pb-Free)
2000 Units/Bag
MC78L08ACPRA
T
J
= 0
to +125
C
TO-92
2000 Tape & Reel
MC78L08ACPRAG
TO-92
(Pb-Free)
2000 Tape & Reel
MC78L08ACPRE
TO-92
2000 Tape & Reel
MC78L08ACPREG
TO-92
(Pb-Free)
2000 Tape & Reel
MC78L08ACPRP
TO-92
2000 Ammo Pack
MC78L08ACPRPG
TO-92
(Pb-Free)
2000 Ammo Pack
MC78L09ABD
SOIC-8
98 Units/Rail
MC78L09ABDG
SOIC-8
(Pb-Free)
98 Units/Rail
MC78L09ABDR2
SOIC-8
2500 Tape & Reel
MC78L09ABDR2G
9.0 V
T
J
= -40
to +125
C
SOIC-8
(Pb-Free)
2500 Tape & Reel
MC78L09ABPRA
9.0 V
T
J
= -40
to +125
C
TO-92
2000 Tape & Reel
MC78L09ABPRAG
TO-92
(Pb-Free)
2000 Tape & Reel
MC78L09ABPRP
TO-92
2000 Ammo Pack
MC78L09ABPRPG
TO-92
(Pb-Free)
2000 Ammo Pack
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
background image
MC78L00A Series, NCV78L00A
http://onsemi.com
11
ORDERING INFORMATION (continued)
Device
Output Voltage
Operating
Temperature Range
Package
Shipping
MC78L09ACD
SOIC-8
98 Units/Rail
MC78L09ACDG
SOIC-8
(Pb-Free)
98 Units/Rail
MC78L09ACDR2
SOIC-8
2500 Tape & Reel
MC78L09ACDR2G
9.0 V
T
J
= 0
to +125
C
SOIC-8
(Pb-Free)
2500 Tape & Reel
MC78L09ACP
TO-92
2000 Units/Bag
MC78L09ACPG
TO-92
(Pb-Free)
2000 Units/Bag
MC78L12ABD
SOIC-8
98 Units/Rail
MC78L12ABDG
SOIC-8
(Pb-Free)
98 Units/Rail
MC78L12ABDR2
SOIC-8
2500 Tape & Reel
MC78L12ABDR2G
SOIC-8
(Pb-Free)
2500 Tape & Reel
MC78L12ABP
TO-92
2000 Units/Bag
MC78L12ABPG
T
J
= -40
to +125
C
TO-92
(Pb-Free)
2000 Units/Bag
MC78L12ABPRP
TO-92
2000 Ammo Pack
MC78L12ABPRPG
TO-92
(Pb-Free)
2000 Ammo Pack
NCV78L12ABDR2*
SOIC-8
2500 Tape & Reel
NCV78L12ABDR2G*
SOIC-8
(Pb-Free)
2500 Tape & Reel
MC78L12ACD
SOIC-8
98 Units/Rail
MC78L12ACDG
12 V
SOIC-8
(Pb-Free)
98 Units/Rail
MC78L12ACDR2
12 V
SOIC-8
2500 Tape & Reel
MC78L12ACDR2G
SOIC-8
(Pb-Free)
2500 Tape & Reel
MC78L12ACP
TO-92
2000 Units/Bag
MC78L12ACPG
TO-92
(Pb-Free)
2000 Units/Bag
MC78L12ACPRA
TO-92
2000 Tape & Reel
MC78L12ACPRAG
T
J
= 0
to +125
C
TO-92
(Pb-Free)
2000 Tape & Reel
MC78L12ACPRE
TO-92
2000 Tape & Reel
MC78L12ACPREG
TO-92
(Pb-Free)
2000 Tape & Reel
MC78L12ACPRM
TO-92
2000 Ammo Pack
MC78L12ACPRMG
TO-92
(Pb-Free)
2000 Ammo Pack
MC78L12ACPRP
TO-92
2000 Ammo Pack
MC78L12ACPRPG
TO-92
(Pb-Free)
2000 Ammo Pack
*NCV78L12A: T
low
= -40
C, T
high
= +125
C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control.
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
background image
MC78L00A Series, NCV78L00A
http://onsemi.com
12
ORDERING INFORMATION (continued)
Device
Output Voltage
Operating
Temperature Range
Package
Shipping
MC78L15ABD
SOIC-8
98 Units/Rail
MC78L15ABDG
SOIC-8
(Pb-Free)
98 Units/Rail
MC78L15ABDR2
SOIC-8
2500 Tape & Reel
MC78L15ABDR2G
SOIC-8
(Pb-Free)
2500 Tape & Reel
MC78L15ABP
TO-92
2000 Units/Bag
MC78L15ABPG
T
J
= -40
to +125
C
TO-92
(Pb-Free)
2000 Units/Bag
MC78L15ABPRA
TO-92
2000 Tape & Reel
MC78L15ABPRAG
TO-92
(Pb-Free)
2000 Tape & Reel
MC78L15ABPRP
TO-92
2000 Ammo Pack
MC78L15ABPRPG
15 V
TO-92
(Pb-Free)
2000 Ammo Pack
MC78L15ACD
15 V
SOIC-8
98 Units/Rail
MC78L15ACDG
SOIC-8
(Pb-Free)
98 Units/Rail
MC78L15ACDR2
SOIC-8
2500 Tape & Reel
MC78L15ACDR2G
SOIC-8
(Pb-Free)
2500 Tape & Reel
MC78L15ACP
TO-92
2000 Units/Bag
MC78L15ACPG
T
J
= 0
to +125
C
TO-92
(Pb-Free)
2000 Units/Bag
MC78L15ACPRA
TO-92
2000 Tape & Reel
MC78L15ACPRAG
TO-92
(Pb-Free)
2000 Tape & Reel
MC78L15ACPRP
TO-92
2000 Ammo Pack
MC78L15ACPRPG
TO-92
(Pb-Free)
2000 Ammo Pack
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
background image
MC78L00A Series, NCV78L00A
http://onsemi.com
13
ORDERING INFORMATION (continued)
Device
Output Voltage
Operating
Temperature Range
Package
Shipping
MC78L18ABP
TO-92
2000 Units/Bag
MC78L18ABPG
T
J
= -40
to +125
C
TO-92
(Pb-Free)
2000 Units/Bag
MC78L18ACP
TO-92
2000 Units/Bag
MC78L18ACPG
TO-92
(Pb-Free)
2000 Units/Bag
MC78L18ACPRA
TO-92
2000 Tape & Reel
MC78L18ACPRAG
18 V
T
J
= 0
to +125
C
TO-92
(Pb-Free)
2000 Tape & Reel
MC78L18ACPRM
T
J
= 0
to +125
C
TO-92
2000 Ammo Pack
MC78L18ACPRMG
TO-92
(Pb-Free)
2000 Ammo Pack
MC78L18ACPRP
TO-92
2000 Ammo Pack
MC78L18ACPRPG
TO-92
(Pb-Free)
2000 Ammo Pack
MC78L24ABP
TO-92
2000 Units/Bag
MC78L24ABPG
T
J
= -40
to +125
C
TO-92
(Pb-Free)
2000 Units/Bag
MC78L24ACP
TO-92
2000 Units/Bag
MC78L24ACPG
24 V
TO-92
(Pb-Free)
2000 Units/Bag
MC78L24ACPRA
24 V
TO-92
2000 Tape & Reel
MC78L24ACPRAG
T
J
= 0
to +125
C
TO-92
(Pb-Free)
2000 Tape & Reel
MC78L24ACPRP
TO-92
2000 Ammo Pack
MC78L24ACPRPG
TO-92
(Pb-Free)
2000 Ammo Pack
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
background image
MC78L00A Series, NCV78L00A
http://onsemi.com
14
ALYWB
G
8LxxA
SOIC-8
D SUFFIX
CASE 751
xx
= 05, 08, 09, 12, or 15
A
= Assembly Location
L
= Wafer Lot
Y
= Year
W
= Work Week
B, C = Temperature Range
G
= Pb-Free Package
MARKING DIAGRAMS
MC78L
zzABP
ALYWW
G
G
zz
= 05, 08, 09, 12, 15, 18 or 24
A
= Assembly Location
L
= Wafer Lot
Y
= Year
WW = Work Week
G
= Pb-Free Package
(Note: Microdot may be in either location)
TO-92
P SUFFIX
CASE 029
ALYWC
G
8LxxA
MC78L
zzACP
ALYWW
G
G
1
2 3
1
8
1
8
1
2 3
background image
MC78L00A Series, NCV78L00A
http://onsemi.com
15
PACKAGE DIMENSIONS
SOIC-8 NB
D SUFFIX
CASE 751-07
ISSUE AF
SEATING
PLANE
1
4
5
8
N
J
X 45
_
K
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751-01 THRU 751-06 ARE OBSOLETE. NEW
STANDARD IS 751-07.
A
B
S
D
H
C
0.10 (0.004)
DIM
A
MIN
MAX
MIN
MAX
INCHES
4.80
5.00
0.189
0.197
MILLIMETERS
B
3.80
4.00
0.150
0.157
C
1.35
1.75
0.053
0.069
D
0.33
0.51
0.013
0.020
G
1.27 BSC
0.050 BSC
H
0.10
0.25
0.004
0.010
J
0.19
0.25
0.007
0.010
K
0.40
1.27
0.016
0.050
M
0
8
0
8
N
0.25
0.50
0.010
0.020
S
5.80
6.20
0.228
0.244
-X-
-Y-
G
M
Y
M
0.25 (0.010)
-Z-
Y
M
0.25 (0.010)
Z
S
X
S
M
_
_
_
_
1.52
0.060
7.0
0.275
0.6
0.024
1.270
0.050
4.0
0.155
mm
inches
SCALE 6:1
*For additional information on our Pb-Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SOLDERING FOOTPRINT*
background image
MC78L00A Series, NCV78L00A
http://onsemi.com
16
PACKAGE DIMENSIONS
TO-92 (TO-226)
P SUFFIX
CASE 29-11
ISSUE AL
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. CONTOUR OF PACKAGE BEYOND DIMENSION R
IS UNCONTROLLED.
4. LEAD DIMENSION IS UNCONTROLLED IN P AND
BEYOND DIMENSION K MINIMUM.
R
A
P
J
L
B
K
G
H
SECTION X-X
C
V
D
N
N
X X
SEATING
PLANE
DIM
MIN
MAX
MIN
MAX
MILLIMETERS
INCHES
A
0.175
0.205
4.45
5.20
B
0.170
0.210
4.32
5.33
C
0.125
0.165
3.18
4.19
D
0.016
0.021
0.407
0.533
G
0.045
0.055
1.15
1.39
H
0.095
0.105
2.42
2.66
J
0.015
0.020
0.39
0.50
K
0.500
---
12.70
---
L
0.250
---
6.35
---
N
0.080
0.105
2.04
2.66
P
---
0.100
---
2.54
R
0.115
---
2.93
---
V
0.135
---
3.43
---
1
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any
liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over
time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under
its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death
may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees,
subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part.
SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 800-282-9855 Toll Free
USA/Canada
Japan: ON Semiconductor, Japan Customer Focus Center
2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051
Phone: 81-3-5773-3850
MC78L00A/D
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 61312, Phoenix, Arizona 85082-1312 USA
Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada
Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.