206
www.recom-international.com
April-2005
10 Watt
2" x 1" Package
Single
&
&
Dual Output
POWERLINE
DC/DC-Converter
RP10-
S_DE
Series
2:1 Wide Input Voltage Range
10 Watts Output Power
1.6kVDC Isolation
Fixed Operating Frequency
Six-Sided Continuous Shield
International Safety Standard Approvals
UL 1950 Component Recognized
Standard 50.8 x25.4x10.2mm Package
Efficiency to 86%
Features
Selection Guide
12V, 24V and 48V Input Types
Part Number
Input Output
Output
Input
(4)
Efficiency
(5)
Capacitive
(6)
Range
Voltage
Current
Current Load max.
VDC VDC mA mA %
F
RP10-123.3SE 9-18 3.3
2000
724
80
6800
RP10-1205SE 9-18 5
2000
1082
81
4700
RP10-1212SE 9-18 12
830
1064
82
690
RP10-1215SE 9-18 15
670
1088
81
470
RP10-243.3SE 18-36 3.3
2000
362
80
6800
RP10-2405SE 18-36 5
2000
534
82
4700
RP10-2412SE 18-36 12
830
519
84
690
RP10-2415SE 18-36 15
670
523
84
470
RP10-483.3SE 36-75 3.3
2000
183
79
6800
RP10-4805SE 36-75 5
2000
260
84
4700
RP10-4812SE 36-75 12
830
253
86
690
RP10-4815SE 36-75 15
670
258
85
470
RP10-1205DE 9-18 5
1000
1068
82
680
RP10-1212DE 9-18 12
416
1053
83
330
RP10-1215DE 9-18 15
333
1041
84
110
RP10-2405DE 18-36 5
1000
548
80
680
RP10-2412DE 18-36 12
416
520
84
330
RP10-2415DE 18-36 15
333
520
84
110
RP10-4805DE 36-75 5
1000
267
82
680
RP10-4812DE 36-75 12
416
254
86
330
RP10-4815DE 36-75 15
333
260
84
110
Description
The E-Series of DC/DC Converters are fully certified to EN 60950: 2000. This makes them ideal for all
Telecom and safety applications where approved isolation is required.
They also meet UL 1950 and CSA 950 standards
(9)
.
www.recom-international.com
207
April-2005
Derating-Graph
(Ambient Temperature)
POWERLINE
DC/DC-Converter
RP10-S_DE
Series
125
75
50
25
0
100
Ambient Temperature Range (C)
-25
-10 0
50 60 70
80 90 100
Output Power (%)
79
Natural Convection
67
125
75
50
25
0
100
Ambient Temperature Range (C)
-25
-10 0
50 60 70 80 90 100
Output Power (%)
81
Natural Convection
76
RP10-2405SE
RP10-2405SE With Heat Sink
125
75
50
25
0
100
Ambient Temperature Range (C)
-25
-10 0
50 60 70
80 90 100
Output Power (%)
79
Natural Convection
67
125
75
50
25
0
100
Ambient Temperature Range (C)
-25
-10 0
50 60 70 80 90 100
Output Power (%)
83
Natural Convection
86
RP10-2405DE
RP10-2405DE With Heat Sink
125
75
50
25
0
100
Ambient Temperature Range (C)
-25
-10 0
50 60 70 80 90 100
Output Power (%)
Natural Convection
125
75
50
25
0
100
Ambient Temperature Range (C)
-25 -10 0
50 60 70 80 90 100
Output Power (%)
85
Natural Convection
-40
RP10-4805SE
RP10-2405SE_DE/M1
125
75
50
25
0
100
Ambient Temperature Range (C)
-25 -10 0
50 60 70 80 90 100
Output Power (%)
85
Natural Convection
-40
125
75
50
25
0
100
Ambient Temperature Range (C)
-25 -10 0
50 60 70 80 90 100
Output Power (%)
88
Natural Convection
-40
RP10-4805SE/M1
RP10-2405SE_DE/M1 With Heat Sink
Derating graphes are valid only for the shown part numbers. If you need detailed derating-information about a
part-number not shown here please contact our technical customer service at info@recom-development.at
208
www.recom-international.com
April-2005
Specifications
(typical at nominal input and 25C unless otherwise noted)
POWERLINE
DC/DC-Converter
RP10-S_DE
Series
Input Voltage Range
12V nominal input
9-18VDC
24V nominal input
18-36VDC
48V nominal input
36-75VDC
Input Filter
Pi Type
Input Surge Voltage (100 ms max.)
12V Input
36VDC
24V Input
50VDC
48V Input
100VDC
Input Reflected Ripple (nominal Vin and full load)
30mAp-p
Start Up Time (nominal Vin and constant resistor load)
20ms typ.
Remote ON/OFF (see note 8)
(Positive logic)
DC-DC ON
Open or 3.5V < Vr < 12V
DC-DC OFF
Short or 0V < Vr < 1.2V
(Negative logic)
DC-DC ON
Short or 0V < Vr < 1.2V
DC-DC OFF
Open or 3.5V < Vr < 12V
Remote OFF input current
Nominal input
2.5mA
Output Power
10W max.
Output Voltage Accuracy (full Load and nominal Vin)
2%
Minimum Load (see Note 1)
10% of FL
Line Regulation (LL-HL at full load)
1%
Load Regulation (25% to 100% FL)
Single
1%
Dual
2%
Cross Regulation (asymmetrical load 25%/100% FL)
5%
Ripple and Noise (20MHz bandwith)
Single
50mVp-p
Dual
75mVp-p
Temperature Coefficient
0.02%/C, max.
Transient Response (25% load step change)
500S
Over Voltage Protection
3.3V output
3.9V
Zener diode clamp
5V output
6.2V
12V output
15V
15V output
18V
Over Load Protection (% of full load at nominal Vin)
150% typ
Short Circuit Protection
Hiccup, automatic recovery
Efficiency
see ,,Selection Guide" table
Isolation Voltage
1.600VDC min.
Isolation Resistance
10
9
min.
Isolation Capacitance
300pF max.
Operating Frequency
300kHz typ.
Approved to Safety Standards
UL 1950, EN60950
Operating Temperature Range
Standard
-25C to +85C(with derating)
(Reference Derating Curve)
M1
-40C to +85C(non derating)
Maximum Case Temperature
+100C
Storage Temperature Range
-55C to +105C
continued on next page
www.recom-international.com
209
April-2005
Specifications
(typical at nominal input and 25C unless otherwise noted)
POWERLINE
DC/DC-Converter
Thermal Impedance
Natural convection
12C/Watt
Natural convection with Heat Sink
10C/Watt
Thermal Shock
MIL-STD-810D
Vibration
10-55Hz, 2G, 30 Min. along X, Y and Z
Relative Humidity
5% to 95% RH
Case Material
Nickel-Coated copper
Base Material
Non-conductive black plastic
Potting Material
Epoxy (UL94-V0)
Conducted Emissions
EN55022
Level A
Radiated Emissions
EN55022
Level A
ESD
EN61000-4-2
Perf. Criteria 2
Radiated Immunity
EN61000-4-3
Perf. Criteria 2
Fast Transient
EN61000-4-4
Perf. Criteria 2
Surge
EN61000-4-5
Perf. Criteria 2
Conducted Immunity
EN61000-4-6
Perf. Criteria 2
Weight
27g
Dimensions
50.8 x 25.4 x 10.2mm
MTBF (see note 2)
1.976 x 10
6
Hours
RP10-S_DE
Series
Notes :
1. The RP10 (W) series required a minimum 10% loading on the output to maintain specified regulation.
Operation under no-load condition will not damage these devices, however they may not meet all listedspecification.
2. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40C. (Ground fixed and controlled environment).
3. Simulated source impedance of 12uH. 12uH inductor in series with +Vin.
4. Maximum value at nominal input voltage and full load of standard type.
5. Typical value at nominal input voltage and full load.
6. Test by minimum Vin and constant resistor load.
7. The ON/OFF control function can be positive or negative logic. The pin voltage is referenced to negative input.
Positive logic ON/OFF is standard, no suffix (Ex. RP10-2405SE)
Negative logic ON/OFF is marked with suffix-N (Ex. RP10-2405SE/N).
8. Heat sink is optional and P/N: 7G-0020A.
9. The M1 version (RP10-xxxxSE/M1, RP10-xxxxDE/M1) does not carry the UL certification.
10.M1 version is more efficient, therefore, it can be operated in a more extensive temperature range than standard version.
11. See application notes for EMI-filtering.
210
www.recom-international.com
April-2005
Package Style and Pinning (mm)
3
1
2
5
4
20.30
50.80
dia.
1.0
10.20
10.20
12.70
15.20
Bottom View
6
2.50
5.10
25.40
5.6
10.20
POWERLINE
DC/DC-Converter
3rd angle
projection
RP10-S_DE
Series
Pin Pitch Tolerance 0.35 mm
Pin Connections
Pin #
Single
Dual
1
+Vin
+Vin
2
-Vin
-Vin
3
+Vout
+Vout
4
No Pin
Com
5
-Vout
-Vout
6
CTRL CTRL
PDF 
ZIP