HA13721RP/FP
Rev.1.00 Jul 23, 2004 page 3 of 8
Electrical Characteristics
(Ta = 25C, 4.5 V < Vcc < 5.5 V)
Item
Symbol
Min
Typ
Max
Unit
Test Conditions
Application
Pin
Supply voltage
Vcc
4.5
--
5.5
V
Vcc
Supply current 1
IccD
--
--
75
mA
Txd: GND, MODE: GND
CANLCANH: 60
Terminal resistor
Vcc
Supply current 2
IccR
--
1.5
6
mA
Txd: open, MODE: GND
CANLCANH: 60
Terminal resistor
Vcc
Supply current 3
IccStby
--
--
250
A
Txd: open, MODE: open
CANL, CANH: open
Vcc
Transmitter Section
RL = 60 (CANL to CANH Terminal resistor)
Vdiff = VCANHVCANL
Recessive; Txd = Vcc, MODE = GND
Dominant; Txd = GND, MODE = GND
(Ta = 25C, 4.5 V < Vcc < 5.5 V)
Item
Symbol
Min
Typ
Max
Unit
Test Conditions
Application
Pin
Input high voltage
VIH
2.4
--
Vcc+0.3
V
Txd, MODE
Input low voltage
VIL
0.3
--
0.8
V
Txd, MODE
Input resistance
Rin
13.5
27
54
k
Txd,
MODE
Recessive bus
voltage
VCANL,
VCANH
2
--
3
V
Recessive (Vcc = 5.0V)
CANL, CANH
Leakage current
ILO
2
--
2
mA
2.0V < CANL, CANH < 7.0V CANL, CANH
VCANH 3 -- 4.5 V
Dominant
CANH
Output voltage
VCANL 0.5 -- 2 V
Dominant
CANL
1.5 -- 3 V
Dominant
4.75 V < Vcc < 5.25 V
42.5
< RL < 60
Difference output
voltage
Vdiff
0.5 -- 0.05 V
Recessive
CANL, CANH
IsCANH 200 --
70 mA
CANH
Output short
current
IsCANL 70 -- 200 mA
CANL
TSD 150
--
190
C
*1
Thermal shutdown
point
TSD(hys) --
10
-- C
*1
Note: 1. It is design specification. The examination at the time of delivery is not performed.
HA13721RP/FP
Rev.1.00 Jul 23, 2004 page 4 of 8
Receiver Section
RL = 60 (CANL to CANH Terminal resistor)
Vdiff = VCANHVCANL
Txd = Vcc, MODE = GND, 2.0 V < CANL, CANH < 7.0 V
(Ta = 25C, 4.5 V < Vcc < 5.5 V)
Item
Symbol
Min
Typ
Max
Unit
Test Conditions
Application
Pin
Difference input
voltage (Recessive)
Vdiff(R) -- -- 0.5 V
CANL,
CANH
Difference input
voltage (Dominant1)
Vdiff(D1) 0.9 -- -- V
CANL,
CANH
Difference input
voltage (Dominant2)
Vdiff(D2)
1.0
--
--
V
MODE: Vcc
CANL, CANH
Difference input
voltage (hysteresis)
Vdiff(hys) 100
--
200 mV Vdiff(hys)
= Vdiff(D1) Vdiff(R)
CANL, CANH
Output high voltage
VOH
0.8Vcc
--
Vcc
V
IRxd = 100
A Rxd
Output low voltage
VOL
--
--
0.1Vcc
V
IRxd = 1 mA
Rxd
Input resistance
(CANH)
Rin 10
--
50
k
CANH
Input resistance
(CANL)
Rin 10
--
50
k
CANL
Input resistance
(CANH, CANL)
Rdiff 20
--
100
k
CANL,
CANH
Receiver Section
RL = 60 (CANL to CANH Terminal resistor)
CL(CANL to CANH) = 100 pF
Txd input tr/tf = 5.0 ns/1.2 V
CRxd(Rxd to GND) = 30 pF
(Ta = 25C, 4.5 V < Vcc < 5.5 V)
Item
Symbol
Min
Typ
Max
Unit
Test Conditions
Application
Pin
Baud rate
--
--
1
Mbps
Delay time 1
tonTxd
--
80
160
ns
MODE: GND, refer fig.1(1)
Txd,
CANL, CANH
Delay time 2
toffTxd
--
100
180
ns
MODE: GND, refer fig.1(1)
Txd,
CANL, CANH
Delay time 3
tonRxd
--
120
280
ns
MODE: GND, refer fig.1(1)
Txd, Rxd
Delay time 4
toffRxd
--
140
280
ns
MODE: GND, refer fig.1(1)
Txd, Rxd
Delay time 5
tConRxd
--
--
150
ns
MODE: GND, refer fig.1(1)
Rxd,
CANL, CANH
Delay time 6
tCoffRxd
--
--
150
ns
MODE: GND, refer fig.1(1)
Rxd,
CANL, CANH
Wakeup 1
tWAKE
--
--
20
s
Txd: GND, refer fig.1(2)
MODE, Rxd
Wakeup 2
tdRxdL
--
--
3
s
Txd: Vcc, MODE: Vcc,
refer fig.1(3)
CANL,CANH,
Rxd
Keep safety first in your circuit designs!
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble
may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary
circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's
application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party.
2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data,
diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of
publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is
therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product
information before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor
home page (http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to
evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes
no responsibility for any damage, liability or other loss resulting from the information contained herein.
5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life
is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a
product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater
use.
6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and
cannot be imported into a country other than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein.
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
http://www.renesas.com
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500 Fax: <1> (408) 382-7501
Renesas Technology Europe Limited.
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, United Kingdom
Tel: <44> (1628) 585 100, Fax: <44> (1628) 585 900
Renesas Technology Europe GmbH
Dornacher Str. 3, D-85622 Feldkirchen, Germany
Tel: <49> (89) 380 70 0, Fax: <49> (89) 929 30 11
Renesas Technology Hong Kong Ltd.
7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2375-6836
Renesas Technology Taiwan Co., Ltd.
FL 10, #99, Fu-Hsing N. Rd., Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999
Renesas Technology (Shanghai) Co., Ltd.
26/F., Ruijin Building, No.205 Maoming Road (S), Shanghai 200020, China
Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952
Renesas Technology Singapore Pte. Ltd.
1, Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
RENESAS SALES OFFICES
2004. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .1.0