(Notice)
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment
using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before
using any SHARP device.
Specifications are subject to change without notice for improvement.
(Internet)
Data for Sharp's optoelectronic/power devices is provided on internet. (Address http://www.sharp.co.jp/ecg/)
(Unit:mm)
OPIC Light Detector for x12 Speed Writing CD-R
Tec. 000602-A
Outline Dimensions
Features
Applications
Specifications
( 1 ) CD-R/RW drives
( 2 ) CD-ROM drives
( 3 ) DVD-ROM drives
GA100T8R1MZ
OPIC Light Detector
(Ta=25C)
Parameter
Symbol
Condition
1
2
3
4
5
6
7
8
9
10
11
12
V
s
V
CC
V
D
NC
13
14
V
A
V
RF
V
C
V
E1
V
E2
NC
V
F2
V
B
V
F1
GND
Terminal connection
Supply voltage
Extremes of off-set voltage
Sensitivity(A,B,C,D)
Sensitivity(RF)
Response frequency
Output noise level
Operating temperature
Vcc
Vod
RP1
RP2
fc(RF)
Vn(RF)
Topr
-
-
-
-
-3 dB
f=54 MHz,BW=30 kHz
-
Input wavelength 650 nm
TYP. 10.2 mV/
W
TYP. 18.9 mV/
W
MIN. 70 MHz
Input wavelength 780 nm
TYP. 11.0 mV/
W
TYP. 20.3 mV/
W
MIN. 60 MHz
Characteristics
4.75 to 5.25 V
MAX.
25 mW
TYP. - 73 dBm
- 10 to + 80C
( 1 ) OPIC light detector with built-in RF amplifier
(Integrates 8-division PIN photodiode and Amp.
IC onto a single chip)
CD-R
: x12 speed writing
CD-RW : x8 speed writing
CD-ROM : x40 speed reading
DVD-ROM: x8 speed reading
( 2 ) Built-in capacitor for power supply bypass
( 3 ) Can read various discs such as DVD,
DVD-ROM, DVD-RAM, DVD-R,
CD-ROM, CD-R, CD-RW
( 4 ) Surface mount-leadless package
(Package dimensions: 5.0 x 5.55 x 1.295mm)
( 5 ) Applicable for reflow
* "OPIC" (Optical IC) is a trademark of SHARP Corporation.
An OPIC consists of a light-detecting element and a signal-processing
circuit integrated onto a single chip.
1/2
5.55
5.0
1
2
3
5
6
7
8
9
10
11
12
13
14
(1.295)
0.895
4
1.6
Detector
Center
Under development
New product
115
Application Circuits
NOTICE
qThe circuit application examples in this publication are provided to explain representative applications of
SHARP devices and are not intended to guarantee any circuit design or license any intellectual property
rights. SHARP takes no responsibility for any problems related to any intellectual property right of a
third party resulting from the use of SHARP's devices.
qContact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
SHARP reserves the right to make changes in the specifications, characteristics, data, materials,
structure, and other contents described herein at any time without notice in order to improve design or
reliability. Manufacturing locations are also subject to change without notice.
qObserve the following points when using any devices in this publication. SHARP takes no responsibility
for damage caused by improper use of the devices which does not meet the conditions and absolute
maximum ratings to be used specified in the relevant specification sheet nor meet the following
conditions:
(i) The devices in this publication are designed for use in general electronic equipment designs such as:
--- Personal computers
--- Office automation equipment
--- Telecommunication equipment [terminal]
--- Test and measurement equipment
--- Industrial control
--- Audio visual equipment
--- Consumer electronics
(ii)Measures such as fail-safe function and redundant design should be taken to ensure reliability and
safety when SHARP devices are used for or in connection with equipment that requires higher
reliability such as:
--- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.)
--- Traffic signals
--- Gas leakage sensor breakers
--- Alarm equipment
--- Various safety devices, etc.
(iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely
high level of reliability and safety such as:
--- Space applications
--- Telecommunication equipment [trunk lines]
--- Nuclear power control equipment
--- Medical and other life support equipment (e.g., scuba).
qContact a SHARP representative in advance when intending to use SHARP devices for any "specific"
applications other than those recommended by SHARP or when it is unclear which category mentioned
above controls the intended use.
qIf the SHARP devices listed in this publication fall within the scope of strategic products described in the
Foreign Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export
such SHARP devices.
qThis publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under
the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any
means, electronic or mechanical, for any purpose, in whole or in part, without the express written
permission of SHARP. Express written permission is also required before any use of this publication
may be made by a third party.
qContact and consult with a SHARP representative if there are any questions about the contents of this
publication.
PDF 
ZIP