104S1LG21
Feb. 7
6
D 18203A
Feb
LD18203A-
1. Application
This
specification
applies to color TFT-LCD module, LQ104S1LG21
These specification sheets are the proprietary product of SHARP CORPORATION("SHARP) and include materials
protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by
any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of
SHARP.
The device listed in these specification sheets was designed and manufactured for use in general electronic
equipment.
In case of using the device for applications such as control and safety equipment for transportation (aircraft, trains,
automobiles, etc.), rescue and security equipment and various safety related equipment which require higher
reliability and safety, take into consideration that appropriate measures such as fail-safe functions and redundant
system design should be taken.
Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications,
telecommunication equipment (trunk lines), nuclear power control equipment and medical or other equipment for life
support.
SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply with
the instructions and the precautions specified in these specification sheets.
Contact and consult with a SHARP sales representative for any questions about this device.
LD18203A-
2. Overview
This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor).
It is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a backlight unit.
Graphics and texts can be displayed on a 800 X 3 X 600 dots panel with 262,144 colors by using LVDS
(Low Voltage Differential Signaling) system for interface and supplying +3.3V DC supply voltage for
TFT-LCD panel driving.
This module is super-high brightness (350cd/m^2).
This module is the type of wide viewingangle the viewing angle is 6 o'clock direction.
Backlight-driving DC/AC inverter is not built in this module.
3. Outline Specifications
Parameter Specifications
Unit
Display size
26 (10.4") Diagonal
cm
Active area
211.2(H)
158.4(V)
mm
Pixel format
800 (H ) X 600 (V)
pixel
(1 pixel=R+G+B dots)
Number of colors
(Number of gray scale level)
262, 144 colors
64 gray scales per color
Pixel pitch
0.264(H)
0.264(V)
mm
Pixel configuration
R,G,B vertical stripe
Display mode
Normally white
Unit outline dimensions *1
246.5(W)
179.4(H)
15.5max(D)
mm
Mass
620 max
g
Surface treatment
Anti-glare and hard-coating 3H
[Note] excluding backlight cables.
LD18203A-
4. Input Terminals
4-1. TFT-LCD panel driving
CN1 (LVDS Signals , +3.3V DC power supply and Contorol signal)
Corresponding connector:FI-SE20ME (FPC Type) or FI-S20S (WireType)
JAE
Pin No.
Symbol
Function
Remark
1 V
CC
+3.3V power supply
2 V
CC
+3.3V power supply
3 GND
4 GND
5
RXIN0-
Differential data input, CH0 (negative)
LVDS signal
6
RXIN0+
Differential data input, CH0 (positive)
LVDS signal
7 GND
8
RXIN1-
Differential data input, CH1 (negative)
LVDS signal
9
RXIN1+
Differential data input, CH1 (positive)
LVDS signal
10 GND
11
RXIN2-
Differential data input, CH2 (negative)
LVDS signal
12
RXIN2+
Differential data input, CH2 (positive)
LVDS signal
13 GND
14
RXCLK IN-
Differential clock input (negative)
LVDS signal
15
RXCLK IN+
Differential clock input (positive)
LVDS signal
16 GND
17
R/L
Horizontal display mode select signal
[Note1]
18
U/D
Vertical display mode select signal
[Note2]
19 GND
20 GND
[Note ]
To obtain the proper relation between LVDS signals and actual digital data signals,
the digital signals should be inputted into the transmitter as described in the nextsection, 4-2.
[Note 1],[Note 2]
R/L = High, U/D = Low
R/L = Low, U/D = Low
R/L = High, U/D = High
R/L = Low, U/D = High
LD18203A-
100
100
100
100
U
s
ing rec
e
iver
S
i
ng
le
L
V
D
S
in
terf
ac
e,
whic
h
e
q
u
a
ls
T
H
C
6
3
L
V
D
F
6
4A
(TH
ine
),
c
o
ntain
ed
in a
co
ntro
l I
C
C
o
rresp
on
ding T
r
ansm
itter
D
S
9
0C
36
3,
D
S
90C
36
3A
, D
S
90C
38
3,
D
S
90
C
383A
N
a
tion
al sem
ico
nd
ucto
r
T
H
C
6
3L
V
D
F63A
,
T
H
C
6
3L
V
D
M
63A
(
T
H
i
ne
)
,
SN
75L
V
D
S
8
4
(
T
i
)
4-2
L
V
DS
I
n
te
r
f
ace
bl
ock diag
ra
m
Syst
e
m
Sid
e
(
TFT
-
L
CD Si
de)
100
100
100
10uF
R0
R5
B0
B5
Hs
yn
c
V
sy
nc
EN
AB
G0
G5
CK
L
VDS T
r
ansmi
tter
R
X
I
N
1+
(
9pi
n)
R
X
I
N
1-
(
8p
i
n)
RX
IN2
+ (
1
2
p
in
)
RX
IN2- (
1
1
p
in
)
RX
CL
KIN+ (1
5p
in)
RX
CL
KIN- (1
4
p
in
)
L
V
DS
Re
c
e
iver
Contr
ol
ler
R/L
U/D
10
K
10
K
R0
R5
B0
B5
Hsync
Vsync
EN
AB
G0
G5
CL
K
R/L
U/D
VC
C
R
X
I
N
0+
(
6pi
n)
R
X
I
N
0-
(
5p
i
n)
100
10
0
10
0
Tx
IN
18
Tx
IN
19
Tx
IN
20
TxCLK I
N
TxI
N
0
5
TxI
N
6
11
TxI
N
1
2
17
PLL
Digit
al S
igna
l
L V
DS Si
gnal
RxOUT1
8
RxOU
T1
9
RxOUT2
0
RxCLK OU
T
RxOUT1
2
17
RxOUT6
11
RxOU
T0
5
PLL
L V
DS Signal
Digi
ta
l Signal
R/L(17pin)
U
/
D
(
18pin)
VCC(1,2pin)
GN
D
GN
D
G
N
D
(
3,4,7,1
0,
1
3,1
6,19,
20pi
n
)
LD18203A-4
LD18203A-
[Note ] Data Mapping
4-3. Backlight driving
CN2 ,CN3
Used connector : BHR-03VS-1(JST)
Corresponding connector :SM02(8.0)B-BHS(JST)
Color of FL cable
Pin no.
symbol
function
CN2 CN3
1
VHIGH Power supply for lamp
(High voltage side)
Pink Pink
2
NC
This is electrically opened.
3
VLOW Power supply for lamp
(Low voltage side)
White White
5. Absolute Maximum Ratings
Parameter Symbol
Condition
Pin
name
Ratings Unit
Remark
+3.3V
supply voltage
Vcc Ta=25
o
C
Vcc
0 to + 4.0
V
Input voltage
VI1
RXINi-/+(i= 0,1,2)
Ta=25
o
C
RXCLK IN-/+
-0.3 to Vcc+0.3
VI2 Ta=25
o
C
R/L , U/D
-0.3 to Vcc+0.3
V
Storage temperature
Tstg
-
-30 to +70
o
C [Note1]
Operating temperature Topa Ambient
-10 to +65
o
C [Note2]
Lamp Input voltage
V
HIGH
0
+ 2000
rms
[Note1]Humidity
95%RH Max. at Ta
50
.
Maximum wet-bulb temperature at 39
or less at Ta>50
.
No condensation.
[Note2]
Humidity
95%RH Max. at Ta
40
.
Maximum wet-bulb temperature at 39
or less at Ta>40
.
No condensation.
LD18203A-
6.Recommended operation condition
Parameter
Symbol Min. Typ. Max. Unit Remark
Supply voltage
3.0
+3.3
3.6
[Note1]
LVDS Signals
L
0
2.4
[Note2]
Input voltage
0
Vcc
[Note3]
Ambient temperature
-10
+65
[Note4]
[Note1]On-off conditions for supply voltage
0<t1
15ms
0<t2
10ms
0<t3
100ms
0<t4
1s
200ms<t5
Vcc-dip conditions
1) 2.5V
Vcc
td
10ms
2) Vcc<2.5V
Vcc-dip conditions should also follow the On-off
conditions for supply voltage
[Note2] RXIN0-, RXIN0+,RXIN1-,RXIN1+,RXIN2-,RXIN2+,
RXCLK IN-,RXCLK IN+
[Note3] R/L, U/D
[Note4] Humidity: 95%RH Max. at Ta=<40
o
C.
Maximum wet-bulb temperature at 39
o
C or less at Ta>40
o
C.
No condensation.
7. Electrical Characteristics
7-1.TFT-LCD panel driving Ta=25
o
C
Parameter
Symbol Min.
Typ.
Max.
Unit
Remark
Current dissipation
Vcc=+3.3V
Icc
-
310
510
mA
[Note1]
Permissive input ripple voltage
VRP
-
-
100
mVp-p
Input voltage range
LVDS signal
VL
0
-
2.4
V
[Note2]
Differential input
High
VTH
-
-
VCM+
100
mV
V
CM
=1.2V
threshold voltage
Low
VTL
VCM
100
- -
mV
[Note3]
Input impedance
(Differential input)
RT
-
100
- [Note2]
Low VIL
- -
0.8
V
[Note4]
Input voltage
High VIH
2.1
- -
[Note5]
Low(VI=0V)
IOL1
-800
- -
Input current1
High(VI=Vcc)
IOH1
-10.0
- 10.0
[Note4]
Low(VI=0V)
IOL2
-10.0
- 10.0
uA
Input current2
High(VI=Vcc)
IOH2
- - 800
uA
[Note5]
[Note1] Typical current situation : 16-gray-bar pattern.
Vcc=+3.3V
[Note2] LVDS signals
[Note3] V
CM
: Common mode voltage of LVDS driver.
[Note4] R/L
[Note5] U/D
T
0.3V
VCC
T1
T
0.9VCC
0.3V
VCC
T
0.9VCC
Signal
Signal
T
2.7V
2.5V
VCC
LD18203A-
7-2. Backlight driving
The backlight system is an edge-lighting type with 2 CCFT (Cold Cathode Fluorescent Tube).
The characteristics of single lamp are shown in the following table.
(It is usually required to measure under the following condition.
I
L
=6.0mA,Ta=25
2
, F
L
=60kHz.
Parameter
Symbol Min.
Typ. Max.
Unit
Remark
Lamp current range
IL
3.5
6.0
7.0
mArms [Note1]
Lamp power consumption
PL
-
2.8
-
W
[Note2]
Lamp
frequency
FL 35 60 70 kHz
[Note3]
Kick-off voltage
Vs
-
-
1450
Vrms Inverter output
[Note4]
-
-
(2000)
Transformer
output
at barast capacitor =12p
Ta=-10
o
C
L
L
50000
-
-
hour
[Note5] I
L=
6.0mA
Lamp life time
L
L
30000
hour [Note5]
I
L=
7.0mA
[Note1] Lamp current is measured with current meter for high frequency as shown below.
[Note2] Referential data per one CCFT by calculation. (I L
VL)
The data don't include loss at inverter. ( IL=6.0mArms)
[Note3] Lamp frequency may produce interference with horizontal synchronous frequency, and this may cause
beat on the display. Therefore lamp frequency shall be detached as much as possible from the
horizontal synchronous frequency and from the harmonics of horizontal synchronous to avoid interference.
[Note4] The voltage above this value should be applied to the lamp for more than 1 second to start-up. Otherwise
the lamp may not be turned on.
[Note5] Since lamp is consumables, the life time written above is referencial value and it is not guaranteed in this
specification sheet by SHARP.
Above value is applicable when lamp (the long side of LCD module) is placed horizontally.
(Landscape position)
Lamp life time is defined that it applied either
or
under this condition
(Continuous turning on at Ta=25
o
C, IL=6.0mArms)
Brightness becomes 50% of the original value under standard condition.
Kick-off voltage at Ta=-10
o
C exceeds maximum value,1450Vrms.
(Lamp lifetime may vary if lamp is in portrait position due to the change of mercury density inside the lamp.)
In case of operating under lower temp environment, the lamp exhaustion is accelerated and the brightness
becomes lower. (Continuous operating for around 1 month under lower temp condition may reduce the
brightness to half of the original brightness.)
In case of such usage under lower temp environment, periodical lamp exchange is recommended.
[Note6] The performance of the backlight, for example life time or brightness, is much influenced by the
characteristics of the DC-AC inverter for the lamp. When you design or order the inverter, please
make sure that a poor lighting caused by the mismatch of the backlight and the inverter
(miss-lighting, flicker, etc.) never occur. When you confirm it, the module should be operated in the
same condition as it is installed in your instrument.
Be sure to use a back light power supply with the safety protection circuit such as the detection circuit
for the excess voltage, excess current and or electric discharge waveform.
Be sure to use the detect circuit by which one side of the CCFT lamps can be controlled independently.
Otherwise, when one side of the CCFT is open, the excess current may possibly be applied to the other side
of the lamp. Recommended inverter is"CXA-P1212B-WJL(TDK)".
[Note7] It is required to have the inverter designed so that to allow the impedance deviation of the
two CCFT lamps and the capacity deviation of barast capacitor.
[Note8] Under the environment of 10lx or less, miss-lighting or lighting delay may occur.
Module
Transformer
output voltage
CN2,3
2pin
CN2,3
1pin
Inverter
Inverter
output voltage
LD18203A-
8. Timing characteristics of input signals
8-1. Timing characteristics
(These are specified at the digital inputs/outputs of LVDS transmitter/receiver.)
C
Data
ENAB
Sync
D
E
F
A
B
(Vertical timing)
Item(symbol) Min.
Typ.
Max.
Unit
Vsync cycle (T
VA
) -
17.6
-
ms
Negative
628
666
798
line
Blanking period(T
VB
) 28
66 -
line
Vsync pulse width (T
VC
) 2 4 6
line
Back porch (T
VD
) 23
23
23
line
Vsync pulse width+Back porch
(T
VC
+T
VD
)
25 27 29
line
Active display area (T
VE
) 600 600 600
line
Front porch (T
VF
) 3
39
-
line
(Horizontal timing)
Item(symbol) Min.
Typ.
Max.
Unit
Remark
Hsync cycle (T
HA
) 20.8
26.4
-
us
Negative
832 1056 - clock
Blanking period (T
HB
) 40
256 -
clock
Hsync pulse width (T
HC
) 2
128
200
clock
Back porch (T
HD
) 58
88
170
clock
Active display area (T
HE
) 800 800 800
clock
Front porch (T
HF
) -
40
-
clock
(Clock signal)
Item Min.
Typ.
Max.
Unit
Remark
Frequency 35
40
42
MHz
[Note1]
[Note1] In case of lower frequency, the deterioration of display quality, flicker etc., may be occurred.
LD18203A-
(Hsync-Vsync Phase difference)
T
HV
Vsync
Hsync
Item(symbol) Min.
Typ.
Max.
Unit
Remark
Hsync-Vsync Phase difference (T
HV
)
1
-
T
HA
-T
HC
clock
(Hsync-ENAB Phase difference)
ENAB
Hsync
T
HN
Item Min.
Typ.
Max.
Unit
Remark
Hsync-ENAB Phase difference (T
HN
)
58 88 170
clock
8-2 Display position
Item Standards
Beginning
Ending
Unit
Remark
Horizontal
rising edge of ENAB
0
800
clock
rising edge of Hsync
88
888
clock [Note1]
Vertical
rising edge of Vsync
23
623
line
[Note1]
In case that ENAB signal is fixed to low level. Do not keep ENAB signal high
during operation.
8-3. Input Data Signals and Display Position on the screen
D1,DH1
D1,DH2
D1,DH3
D2,DH2
D2,DH1
D3,DH1
R G B
Display position of input data
( H , V
D800,
D1,DH600
D800,DH1
DH600
LD18203A-
9. Input Signals, Basic Display Colors and Gray Scale of Each Color
Colors & Data signal
Gray
scale
Gray
Scale
R0 R1
R2 R3 R4
R5
G0
G1
G2
G3
G4
G5
B0 B1 B2 B3
B4
B5
Black
-
0 0 0 0 0 0
0
0
0
0
0
0
0 0 0 0
0
0
Blue
-
0 0 0 0 0 0
0
0
0
0
0
0
1 1 1 1
1
1
Green
-
0 0 0 0 0 0
1
1
1
1
1
1
0 0 0 0
0
0
Cyan
-
0 0 0 0 0 0
1
1
1
1
1
1
1 1 1 1
1
1
Red
-
1 1 1 1 1 1
0
0
0
0
0
0
0 0 0 0
0
0
Magenta -
1 1 1 1 1 1
0
0
0
0
0
0
1 1 1 1
1
1
Yellow
-
1 1 1 1 1 1
1
1
1
1
1
1
0 0 0 0
0
0
White
-
1 1 1 1 1 1
1
1
1
1
1
1
1 1 1 1
1
1
Black GS0 0 0 0 0 0 0
0
0
0
0
0
0
0 0 0 0
0
0
GS1 1 0 0 0 0 0
0
0
0
0
0
0
0 0 0 0
0
0
Darker GS2 0 1 0 0 0 0
0
0
0
0
0
0
0 0 0 0
0
0
Brighter GS61 1 0 1 1 1 1
0
0
0
0
0
0
0 0 0 0
0
0
GS62 0 1 1 1 1 1
0
0
0
0
0
0
0 0 0 0
0
0
Red GS63 1 1 1 1 1 1
0
0
0
0
0
0
0 0 0 0
0
0
Black GS0 0 0 0 0 0 0
0
0
0
0
0
0
0 0 0 0
0
0
GS1 0 0 0 0 0 0
1
0
0
0
0
0
0 0 0 0
0
0
Darker GS2 0 0 0 0 0 0
0
1
0
0
0
0
0 0 0 0
0
0
Brighter GS61 0 0 0 0 0 0
1
0
1
1
1
1
0 0 0 0
0
0
GS62 0 0 0 0 0 0
0
1
1
1
1
1
0 0 0 0
0
0
Green GS63 0 0 0 0 0 0
1
1
1
1
1
1
0 0 0 0
0
0
Black GS0 0 0 0 0 0 0
0
0
0
0
0
0
0 0 0 0
0
0
GS1 0 0 0 0 0 0
0
0
0
0
0
0
1 0 0 0
0
0
Darker GS2 0 0 0 0 0 0
0
0
0
0
0
0
0 1 0 0
0
0
Brighter GS61 0 0 0 0 0 0
0
0
0
0
0
0
1 0 1 1
1
1
GS62 0 0 0 0 0 0
0
0
0
0
0
0
0 1 1 1
1
1
Blue GS63 0 0 0 0 0 0
0
0
0
0
0
0
1 1 1 1
1
1
0 :Low level voltage, 1 : High level voltage
Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of
total 18 bit data signals, the 262,144-color display can be achieved on the screen.
Basic Color
Gray Scale of Red
Gray Scale of Green
Gray Scale of Blue
LD18203A-
10. Optical Characteristics
Ta=25
o
C, Vcc=+3.3V
Parameter
Symbol Condition Min.
Typ. Max. Unit
Remark
Viewing Horizontal
21,
22
CR>10 60 70 - Deg. [Note1]
angle
Vertical
11
35
40
-
Deg.
[Note4]
range
12
55
70
-
Deg.
Contrast ratio
CRn
=0
o
150 - - -
[Note2]
CRo
Optimum
viewing angle
- 300 - -
[Note4]
Response Rise
r
=0
o
- 10 - ms
[Note3]
time
Decay
d
-
25
-
ms
[Note4]
x
0.263
0.313
0.363
-
[Note4]
Chromaticity
of white
y
0.279
0.329
0.379
-
Y
L1
280
350
-
cd/m
2
IL=6.0mArms
fL=60kHz
Luminance of white
White Uniformity
W
-
-
1.45
-
[Note5]
21,
22
- 35 - Deg.
11
- 25 - Deg.
Viewing
angle
range within
defined brightness
12
50% of the
maximum
brightness
- 30 - Deg.
[Note1]
The measurement shall be executed 30 minutes after lighting at rating.
The optical characteristics shall be measured in a dark room or equivalent state with the method shown in
Fig.3 below.
Photodetector
Viewing angle/Response time : BM-5A (TOPCON)
Contrast ratio/Luminance of white/Chromaticity : SR-3(TOPCON)
Fig.3 Optical characteristics measurement method
Center of the screen
TFT-LCD module
Field=1
LCD panel
LD18203A-
[Note1]Definitions of viewing angle range:
N o rm a l lin e
2 2
1 2
11
2 1
6 o 'c lo c k d ire c tio n
[Note2]Definition of contrast ratio:
The contrast ratio is defined as the following.
Contrast Ratio (CR) =
[Note3]Definition of response time:
The response time is defined as the following figure and shall be measured by
switching the input signal for "black" and "white" .
90%
100%
white
white
black
10%
0%
r
d
time
P
hotodetec
tor output
(relativ
e
V
a
lue)
[Note4]This shall be measured at center of the screen.
[Note5]Definition of white uniformity:
White uniformity is defined as the
following with five measurements
(A~E).
11. Display Quality
The display quality of the color TFT-LCD module shall be in compliance with the Incoming
Inspection Standard.
Luminance (brightness) with all pixels white
Luminance (brightness) with all pixels black
Maximum Luminance of five points (brightness)
Minimum Luminance of five points (brightness)
A
B
C
D
E
pixel
200
400
600 pixel
150
300
450
LD18203A-
12.Handling Precautions
a) Be sure to turn off the power supply when inserting or disconnecting the cable.
b) Be sure to design the cabinet so that the module can be installed without any extra stress such as
warp or twist.
c) Since the front polarizer is easily damaged, pay attention not to scratch it.
d) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
Handle with care.
g) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth
when handling.Observe all other precautionary requirements in handling components.
h) Since there is a circuit board in the module back, stress is not added at the time of a design assembly.
Please make it like. If stress is added, there is a possibility that circuit parts may be damaged.
i) Protection film is attached to the module surface to prevent it from being scratched .
Peel the film off slowly , just before the use, with strict attention to electrostatic charges.
Blow off 'dust' on the polarizer by using an ionized nitrogen.
j) The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching
protective board over the LCD, be careful about the optical interface fringe etc. which degrades
display quality.
k) Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD
panel is used under such environment
l) Connect GND to 4 place of mounting holes to stabilize against EMI and external noise.
m) There are high voltage portions on the backlight and very dangerous. Careless touch may lead to
electrical shock. When exchange lamps or service, turn off the power without tail.
n) When handling LCD modules and assembling them into cabinets, please be noted that long-term
storage in the environment of oxidization or deoxidization gas and the use of such materials as
reagent,solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and
discoloration of the LCD modules.
o) Cold cathode fluorescent lamp in LCD panel contains a small amount of mercury, please follow local
ordinances or regulations for disposal.
p) Be careful of a back light lead not to pull by force at the time of the wiring to an inverter,
or line processing.
q) When install LCD modules in the cabinet, please tighten with "torque=0.294
0.02N m(3.0
0.2kgf cm)".
r) Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it gets
inside your eye or mouth by mistake.
s) Notice:Never dismantle the module , because it will cause failure.
t) Be careful when using it for long time with fixed pattern display as it may cause afterimage.
u) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.
If adjusted value is changed, the specification may not be satisfied.
v) If a minute particle enters in the module and adheres to an optical material, it may cause display non-
uniformity issue, etc. Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you
intend to install a fan.
13. Packing form
Product country
JAPAN
TAIWAN
CHINA
Piling number of cartons
5
Max
Package quantity in one carton
20
Carton size
494(W)326(D)433(H)
Total mass of one carton filled
with full modules
15.6kg
Packing form
Fig3
LD18203A-
14.Reliability test items
No. Test item
Conditions
Remark
1 High temperature storage test
Ta=70
240h
2 Low temperature storage test
Ta= -30
240h
3 High temperature
& high humidity operation test
Ta=40
; 95%RH 240h
(No condensation)
4 High temperature operation test
Ta=65
240h
5 Low temperature operation test
Ta= -10
240h
6 Vibration test
(non- operating)
Frequency: 10
57Hz/Vibration width (one side):0.075mm
: 57
500Hz/Gravity:9.8m/s
2
Sweep time : 11 minutes
Test period : 3 hours
(1 hour for each direction of X,Y,Z)
7 Shock test
(non- operating)
Max. gravity : 490m/s
2
Pulse width : 11ms, half sine wave
Direction :
X,
Y,
Z once for each direction.
8 ESD test
Contact discharge (
150pF 330
)
non-operating =
10kV, operating =
8kV
Atmospheric discharge (
150pF 330
)
non-operating =
20kV, operating =
15kV
9 EMI
Measurement in 10m site
Display position on the screen = "H" (full-screen),
GND to 4 place = un-connect, Vcc / Vsignal = typ.
VCCI
(Class B)
[Result Evaluation Criteria]
Under the display quality test conditions with normal operation state, these shall be no change
which may affect practical display function. (normal operation state
Temperature:15
35
,
Humidity:45
75
, Atmospheric pressure:86
106kpa)
15.Others
1) Lot number Label:
Lot No.
15-2 Packing box Label:
LQ104S1LG21
Barcode
Barcode
Barcode
Lot number (DATE)
Quantity of module
TYPE
QUANTITY
DATE
LQ104S1LG21
20pcs
2005.6.1
Quantity of module
: Japan
Quantity
of
module
: Taiwan or China
LQ104S1LG21
*
15-3 If any problem occurs in relation to the description of this specification , it shall be resolved
through discussion with spirit of cooperation.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited
Warranty for SHARP's product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied.
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND
FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or in any way responsible,
for any incidental or consequential economic or property damage.
NORTH AMERICA
EUROPE
JAPAN
SHARP Microelectronics of the Americas
5700 NW Pacific Rim Blvd.
Camas, WA 98607, U.S.A.
Phone: (1) 360-834-2500
Fax: (1) 360-834-8903
Fast Info: (1) 800-833-9437
www.sharpsma.com
SHARP Microelectronics Europe
Division of Sharp Electronics (Europe) GmbH
Sonninstrasse 3
20097 Hamburg, Germany
Phone: (49) 40-2376-2286
Fax: (49) 40-2376-2232
www.sharpsme.com
SHARP Corporation
Electronic Components & Devices
22-22 Nagaike-cho, Abeno-Ku
Osaka 545-8522, Japan
Phone: (81) 6-6621-1221
Fax: (81) 6117-725300/6117-725301
www.sharp-world.com
TAIWAN
SINGAPORE
KOREA
SHARP Electronic Components
(Taiwan) Corporation
8F-A, No. 16, Sec. 4, Nanking E. Rd.
Taipei, Taiwan, Republic of China
Phone: (886) 2-2577-7341
Fax: (886) 2-2577-7326/2-2577-7328
SHARP Electronics (Singapore) PTE., Ltd.
438A, Alexandra Road, #05-01/02
Alexandra Technopark,
Singapore 119967
Phone: (65) 271-3566
Fax: (65) 271-3855
SHARP Electronic Components
(Korea) Corporation
RM 501 Geosung B/D, 541
Dohwa-dong, Mapo-ku
Seoul 121-701, Korea
Phone: (82) 2-711-5813 ~ 8
Fax: (82) 2-711-5819
CHINA
HONG KONG
SHARP Microelectronics of China
(Shanghai) Co., Ltd.
28 Xin Jin Qiao Road King Tower 16F
Pudong Shanghai, 201206 P.R. China
Phone: (86) 21-5854-7710/21-5834-6056
Fax: (86) 21-5854-4340/21-5834-6057
Head Office:
No. 360, Bashen Road,
Xin Development Bldg. 22
Waigaoqiao Free Trade Zone Shanghai
200131 P.R. China
Email: smc@china.global.sharp.co.jp
SHARP-ROXY (Hong Kong) Ltd.
3rd Business Division,
17/F, Admiralty Centre, Tower 1
18 Harcourt Road, Hong Kong
Phone: (852) 28229311
Fax: (852) 28660779
www.sharp.com.hk
Shenzhen Representative Office:
Room 13B1, Tower C,
Electronics Science & Technology Building
Shen Nan Zhong Road
Shenzhen, P.R. China
Phone: (86) 755-3273731
Fax: (86) 755-3273735
PDF 
ZIP