ChipFind - документация

Электронный компонент: 74AC574MTR

Скачать:  PDF   ZIP
1/11
April 2001
s
HIGH SPEED:
f
MAX
= 250MHz (TYP.) at V
CC
= 5V
s
LOW POWER DISSIPATION:
I
CC
= 4
A(MAX.) at T
A
=25C
s
HIGH NOISE IMMUNITY:
V
NIH
= V
NIL
= 28 % V
CC
(MIN.)
s
50
TRANSMISSION LINE DRIVING
CAPABILITY
s
SYMMETRICAL OUTPUT IMPEDANCE:
|I
OH
| = I
OL
= 24mA (MIN)
s
BALANCED PROPAGATION DELAYS:
t
PLH
t
PHL
s
OPERATING VOLTAGE RANGE:
V
CC
(OPR) = 2V to 6V
s
PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 574
s
IMPROVED LATCH-UP IMMUNITY
DESCRIPTION
The 74AC574 is an advanced high-speed CMOS
OCTAL D-TYPE FLIP-FLOP with 3 STATE
OUTPUTS NON INVERTING fabricated with
sub-micron silicon gate and double-layer metal
wiring C
2
MOS technology.
These 8 bit D-Type Flip-Flop are controlled by a
clock input (CK) and an output enable input (OE).
On the positive transition of the clock, the Q
outputs will be set to the logic that were setup at
the D inputs.
While the (OE) input is low, the 8 outputs will be in
a normal logic state (high or low logic level); while
OE is in high level, the outputs will be in a high
impedance state.
The output control does not affect the internal
operation of flip-flops; that is, the old data can be
retained or the new data can be entered even
while the outputs are off.
All inputs and outputs are equipped with
protection circuits against static discharge, giving
them 2KV ESD immunity and transient excess
voltage.
74AC574
OCTAL D-TYPE FLIP-FLOP
WITH 3 STATE OUTPUTS (NON INVERTED)
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
PACKAGE
TUBE
T & R
DIP
74AC574B
SOP
74AC574M
74AC574MTR
TSSOP
74AC574TTR
TSSOP
DIP
SOP
74AC574
2/11
INPUT AND OUTPUT EQUIVALENT CIRCUIT
PIN DESCRIPTION
TRUTH TABLE
X : Don't Care
Z : High Impedance
LOGIC DIAGRAM
This logic diagram has not be used to estimate propagation delays
PIN No
SYMBOL
NAME AND FUNCTION
1
OE
3-State Output Enable
(Active LOW)
2, 3, 4, 5, 6,
7, 8, 9
D0 to D7
Data Inputs
12, 13, 14,
15, 16, 17,
18, 19
Q0 to Q7
3-State Outputs
11
CLOCK
Clock Input (LOW-to-HIGH
Edge Trigger)
10
GND
Ground (0V)
20
V
CC
Positive Supply Voltage
INPUTS
OUTPUT
OE
CK
D
Q
H
X
X
Z
L
X
NO CHANGE
L
L
L
L
H
H
74AC574
3/11
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied.
RECOMMENDED OPERATING CONDITIONS
1) V
IN
from 30% to 70% of V
CC
Symbol
Parameter
Value
Unit
V
CC
Supply Voltage
-0.5 to +7
V
V
I
DC Input Voltage
-0.5 to V
CC
+ 0.5
V
V
O
DC Output Voltage
-0.5 to V
CC
+ 0.5
V
I
IK
DC Input Diode Current
20
mA
I
OK
DC Output Diode Current
20
mA
I
O
DC Output Current
50
mA
I
CC
or I
GND
DC V
CC
or Ground Current
400
mA
T
stg
Storage Temperature
-65 to +150
C
T
L
Lead Temperature (10 sec)
300
C
Symbol
Parameter
Value
Unit
V
CC
Supply Voltage
2 to 6
V
V
I
Input Voltage
0 to V
CC
V
V
O
Output Voltage
0 to V
CC
V
T
op
Operating Temperature
-55 to 125
C
dt/dv
Input Rise and Fall Time V
CC
= 3.0, 4.5 or 5.5V (note 1)
8
ns/V
74AC574
4/11
DC SPECIFICATIONS
1) Maximum test duration 2ms, one output loaded at time
2) Incident wave switching is guaranteed on transmission lines with impedances as low as 50
Symbol
Parameter
Test Condition
Value
Unit
V
CC
(V)
T
A
= 25C
-40 to 85C
-55 to 125C
Min.
Typ.
Max.
Min.
Max.
Min.
Max.
V
IH
High Level Input
Voltage
3.0
V
O
= 0.1 V or
V
CC
-0.1V
2.1
1.5
2.1
2.1
V
4.5
3.15
2.25
3.15
3.15
5.5
3.85
2.75
3.85
3.85
V
IL
Low Level Input
Voltage
3.0
V
O
= 0.1 V or
V
CC
-0.1V
1.5
0.9
0.9
0.9
V
4.5
2.25
1.35
1.35
1.35
5.5
2.75
1.65
1.65
1.65
V
OH
High Level Output
Voltage
3.0
I
O
=-50
A
2.9
2.99
2.9
2.9
V
4.5
I
O
=-50
A
4.4
4.49
4.4
4.4
5.5
I
O
=-50
A
5.4
5.49
5.4
5.4
3.0
I
O
=-12 mA
2.56
2.46
2.4
4.5
I
O
=-24 mA
3.86
3.76
3.7
5.5
I
O
=-24 mA
4.86
4.76
4.7
V
OL
Low Level Output
Voltage
3.0
I
O
=50
A
0.002
0.1
0.1
0.1
V
4.5
I
O
=50
A
0.001
0.1
0.1
0.1
5.5
I
O
=50
A
0.001
0.1
0.1
0.1
3.0
I
O
=12 mA
0.36
0.44
0.5
4.5
I
O
=24 mA
0.36
0.44
0.5
5.5
I
O
=24 mA
0.36
0.44
0.5
I
I
Input Leakage
Current
5.5
V
I
= V
CC
or GND
0.1
1
1
A
Ioz
High Impedance
Output Leakege
Current
5.5
V
I
= V
IH
or V
IL
V
O
= V
CC
or GND
0.5
2.5
5
A
I
CC
Quiescent Supply
Current
5.5
V
I
= V
CC
or GND
4
40
80
A
I
OLD
Dynamic Output
Current (note 1, 2)
5.5
V
OLD
= 1.65 V max
75
50
mA
I
OHD
V
OHD
= 3.85 V min
-75
-50
mA
74AC574
5/11
AC ELECTRICAL CHARACTERISTICS (C
L
= 50 pF, R
L
= 500
, Input t
r
= t
f
= 3ns)
(*) Voltage range is 3.3V
0.3V
(**) Voltage range is 5.0V
0.5V
CAPACITIVE CHARACTERISTICS
1) C
PD
is defined as the value of the IC's internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. I
CC(opr)
= C
PD
x V
CC
x f
IN
+ I
CC
/n (per circuit)
Symbol
Parameter
Test Condition
Value
Unit
V
CC
(V)
T
A
= 25C
-40 to 85C
-55 to 125C
Min.
Typ.
Max.
Min.
Max.
Min.
Max.
t
PLH
t
PHL
Propagation Delay
Time
CK to Q
3.3
(*)
6.5
13.5
15.0
16.5
ns
5.0
(**)
5.0
9.5
11.0
11.5
t
PZL
t
PZH
Output Enable
Time
3.3
(*)
7.0
11.0
12.0
13.0
ns
5.0
(**)
5.0
8.5
9.0
9.5
t
PLZ
t
PHZ
Output Disable
Time
3.3
(*)
6.5
12.0
13.0
14.0
ns
5.0
(**)
5.0
9.5
10.5
11.5
t
W
CLOCK Pulse
Width HIGH or
LOW
3.3
(*)
1.5
6.0
7.0
7.0
ns
5.0
(**)
1.5
4.0
5.0
5.0
t
s
Setup Time D to
CK, HIGH or LOW
3.3
(*)
-0.5
2.5
3.0
3.0
ns
5.0
(**)
0
1.5
2.0
2.0
t
h
Hold Time D to CK,
HIGH or LOW
3.3
(*)
0.5
2.5
3.0
3.0
ns
5.0
(**)
0
1.5
2.0
2.0
f
MAX
Maximum Clock
Frequency
3.3
(*)
75
220
60
60
MHz
5.0
(**)
95
250
85
85
Symbol
Parameter
Test Condition
Value
Unit
V
CC
(V)
T
A
= 25C
-40 to 85C
-55 to 125C
Min.
Typ.
Max.
Min.
Max.
Min.
Max.
C
IN
Input Capacitance
5.0
4
pF
C
OUT
Output
Capacitance
5.0
8
pF
C
PD
Power Dissipation
Capacitance (note
1)
5.0
f
IN
= 10MHz
18
pF