ChipFind - документация

Электронный компонент: 74LVC04AMTR

Скачать:  PDF   ZIP
1/8
February 2002
s
5V TOLERANT INPUTS
s
HIGH SPEED: t
PD
= 4.5ns (MAX.) at V
CC
= 3V
s
POWER DOWN PROTECTION ON INPUTS
AND OUTPUTS
s
SYMMETRICAL OUTPUT IMPEDANCE:
|I
OH
| = I
OL
= 24mA (MIN) at V
CC
= 3V
s
PCI BUS LEVELS GUARANTEED AT 24 mA
s
BALANCED PROPAGATION DELAYS:
t
PLH
t
PHL
s
OPERATING VOLTAGE RANGE:
V
CC
(OPR) = 1.65V to 3.6V (1.2V Data
Retention)
s
PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 00
s
LATCH-UP PERFORMANCE EXCEEDS
500mA (JESD 17)
s
ESD PERFORMANCE:
HBM > 2000V (MIL STD 883 method 3015);
MM > 200V
DESCRIPTION
The 74LVC04A is a low voltage CMOS HEX
INVERTER fabricated with sub-micron silicon
gate and double-layer metal wiring C
2
MOS
technology. It is ideal for 1.65 to 3.6 V
CC
operations and low power and low noise
applications.
It can be interfaced to 5V signal environment for
inputs in mixed 3.3/5V system.
It has more speed performance at 3.3V than 5V
AC/ACT family, combined with a lower power
consumption.
All inputs and outputs are equipped with
protection circuits against static discharge, giving
them 2KV ESD immunity and transient excess
voltage.
74LVC04A
LOW VOLTAGE CMOS HEX INVERTER
HIGH PERFORMANCE
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
PACKAGE
TUBE
T & R
SOP
74LVC04AM
74LVC04AMTR
TSSOP
74LVC04ATTR
TSSOP
SOP
74LVC04A
2/8
INPUT AND OUTPUT EQUIVALENT CIRCUIT
PIN DESCRIPTION
TRUTH TABLE
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
1) I
O
absolute maximum rating must be observed
2) V
O
< GND
PIN No
SYMBOL
NAME AND FUNCTION
1,3,5,9,11,13
1A to 6A
Data Inputs
2, 4, 6, 8,
10, 12
1Y to 6Y
Data Outputs
7
GND
Ground (0V)
14
V
CC
Positive Supply Voltage
A
Y
L
H
H
L
Symbol
Parameter
Value
Unit
V
CC
Supply Voltage
-0.5 to +7.0
V
V
I
DC Input Voltage
-0.5 to +7.0
V
V
O
DC Output Voltage (V
CC
= 0V)
-0.5 to +7.0
V
V
O
DC Output Voltage (High or Low State) (note 1)
-0.5 to V
CC
+ 0.5
V
I
IK
DC Input Diode Current
- 50
mA
I
OK
DC Output Diode Current (note 2)
- 50
mA
I
O
DC Output Current
50
mA
I
CC
or I
GND
DC V
CC
or Ground Current per Supply Pin
100
mA
T
stg
Storage Temperature
-65 to +150
C
T
L
Lead Temperature (10 sec)
300
C
74LVC04A
3/8
RECOMMENDED OPERATING CONDITIONS
1) Truth Table guaranteed: 1.2V to 3.6V
2) V
IN
from 0.8V to 2V at V
CC
= 3.0V
DC SPECIFICATIONS
Symbol
Parameter
Value
Unit
V
CC
Supply Voltage (note 1)
1.65 to 3.6
V
V
I
Input Voltage
0 to 5.5
V
V
O
Output Voltage (V
CC
= 0V)
0 to 5.5
V
V
O
Output Voltage (High or Low State)
0 to V
CC
V
I
OH
, I
OL
High or Low Level Output Current (V
CC
= 3.0 to 3.6V)
24
mA
I
OH
, I
OL
High or Low Level Output Current (V
CC
= 2.7 to 3.0V)
12
mA
I
OH
, I
OL
High or Low Level Output Current (V
CC
= 2.3 to 2.7V)
8
mA
I
OH
, I
OL
High or Low Level Output Current (V
CC
= 1.65 to 2.3V)
4
mA
T
op
Operating Temperature
-55 to 125
C
dt/dv
Input Rise and Fall Time (note 2)
0 to 10
ns/V
Symbol
Parameter
Test Condition
Value
Unit
V
CC
(V)
-40 to 85 C
-55 to 125 C
Min.
Max.
Min.
Max.
V
IH
High Level Input
Voltage
1.65 to 1.95
0.65V
CC
0.65V
CC
V
2.3 to 2.7
1.7
1.7
2.7 to 3.6
2
2
V
IL
Low Level Input
Voltage
1.65 to 1.95
0.35V
CC
0.35V
CC
V
2.3 to 2.7
0.7
0.7
2.7 to 3.6
0.8
0.8
V
OH
High Level Output
Voltage
1.65 to 3.6
I
O
=-100
A
V
CC
-0.2
V
CC
-0.2
V
1.65
I
O
=-4 mA
1.2
1.2
2.3
I
O
=-8 mA
1.7
1.7
2.7
I
O
=-12 mA
2.2
2.2
3.0
I
O
=-18 mA
2.4
2.4
3.0
I
O
=-24 mA
2.2
2.2
V
OL
Low Level Output
Voltage
1.65 to 3.6
I
O
=100
A
0.2
0.2
V
1.65
I
O
=4 mA
0.45
0.45
2.3
I
O
=8 mA
0.7
0.7
2.7
I
O
=12 mA
0.4
0.4
3.0
I
O
=24 mA
0.55
0.55
I
I
Input Leakage
Current
3.6
V
I
= 0 to 5.5V
5
5
A
I
off
Power Off Leakage
Current
0
V
I
or V
O
= 5.5V
100
100
A
I
CC
Quiescent Supply
Current
3.6
V
I
= V
CC
or GND
10
10
A
V
I
or V
O
= 3.6 to
5.5V
10
10
I
CC
I
CC
incr. per Input
2.7 to 3.6
V
IH
= V
CC
-0.6V
500
500
A
74LVC04A
4/8
DYNAMIC SWITCHING CHARACTERISTICS
1) Number of output defined as "n". Measured with "n-1" outputs switching from HIGH to LOW or LOW to HIGH. The remaining output is
measured in the LOW state.
AC ELECTRICAL CHARACTERISTICS
1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switch-
ing in the same direction, either HIGH or LOW (t
OSLH
= | t
PLHm
- t
PLHn
|, t
OSHL
= | t
PHLm
- t
PHLn
|
2) Parameter guaranteed by design
CAPACITIVE CHARACTERISTICS
1) C
PD
is defined as the value of the IC's internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. I
CC(opr)
= C
PD
x V
CC
x f
IN
+ I
CC
/n (per circuit)
Symbol
Parameter
Test Condition
Value
Unit
V
CC
(V)
T
A
= 25 C
Min.
Typ.
Max.
V
OLP
Dynamic Low Level Quiet
Output (note 1)
3.3
C
L
= 50pF
V
IL
= 0V, V
IH
= 3.3V
0.8
V
V
OLV
-0.8
Symbol
Parameter
Test Condition
Value
Unit
V
CC
(V)
C
L
(pF)
R
L
(
)
t
s
= t
r
(ns)
-40 to 85 C
-55 to 125 C
Min.
Max.
Min.
Max.
t
PLH
t
PHL
Propagation Delay
Time
1.65 to 1.95
30
1000
2.0
9.5
12.5
ns
2.3 to 2.7
30
500
2.0
7.0
10
2.7
50
500
2.5
5.5
6.6
3.0 to 3.6
50
500
2.5
1
4.5
1
5.4
t
OSLH
t
OSHL
Output To Output
Skew Time (note1,
2)
2.7 to 3.6
1
1
ns
Symbol
Parameter
Test Condition
Value
Unit
V
CC
(V)
T
A
= 25 C
Min.
Typ.
Max.
C
IN
Input Capacitance
4
pF
C
PD
Power Dissipation Capacitance
(note 1)
1.8
f
IN
= 10MHz
37
pF
2.5
37
3.3
41
74LVC04A
5/8
TEST CIRCUIT
R
T
= Z
OUT
of pulse generator (typically 50
)
TEST CIRCUIT AND WAVEFORM SYMBOL VALUE
WAVEFORM: PROPAGATION DELAY (f=1MHz; 50% duty cycle)
Symbol
V
CC
1.65 to 1.95V
2.3 to 2.7V
2.7V
3.0 to 3.6V
C
L
30pF
30pF
50pF
50pF
R
L
1000
500
500
500
V
IH
V
CC
V
CC
2.7V
2.7V
V
M
V
CC
/2
V
CC
/2
1.5V
1.5V
V
OH
V
CC
V
CC
3.0V
3.0V
t
r
= t
r
<2.0ns
<2.0ns
<2.5ns
<2.5ns
74LVC04A
6/8
DIM.
mm.
inch
MIN.
TYP
MAX.
MIN.
TYP.
MAX.
A
1.75
0.068
a1
0.1
0.2
0.003
0.007
a2
1.65
0.064
b
0.35
0.46
0.013
0.018
b1
0.19
0.25
0.007
0.010
C
0.5
0.019
c1
45 (typ.)
D
8.55
8.75
0.336
0.344
E
5.8
6.2
0.228
0.244
e
1.27
0.050
e3
7.62
0.300
F
3.8
4.0
0.149
0.157
G
4.6
5.3
0.181
0.208
L
0.5
1.27
0.019
0.050
M
0.68
0.026
S
8 (max.)
SO-14 MECHANICAL DATA
PO13G
74LVC04A
7/8
DIM.
mm.
inch
MIN.
TYP
MAX.
MIN.
TYP.
MAX.
A
1.2
0.047
A1
0.05
0.15
0.002
0.004
0.006
A2
0.8
1
1.05
0.031
0.039
0.041
b
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.0089
D
4.9
5
5.1
0.193
0.197
0.201
E
6.2
6.4
6.6
0.244
0.252
0.260
E1
4.3
4.4
4.48
0.169
0.173
0.176
e
0.65 BSC
0.0256 BSC
K
0
8
0
8
L
0.45
0.60
0.75
0.018
0.024
0.030
TSSOP14 MECHANICAL DATA
c
E
b
A2
A
E1
D
1
PIN 1 IDENTIFICATION
A1
L
K
e
0080337D
74LVC04A
8/8
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from
its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications
mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information
previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or
systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics
2002 STMicroelectronics - Printed in Italy - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco
Singapore - Spain - Sweden - Switzerland - United Kingdom - United States.
http://www.st.com