LM158, LM158A, LM258, LM258A
LM358, LM358A, LM358Y, LM2904, LM2904Q
DUAL OPERATIONAL AMPLIFIERS
SLOS068C JUNE 1976 REVISED JULY 1998
1
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
D
Wide Range of Supply Voltages:
Single Supply . . . 3 V to 30 V
(LM2904 and LM2904Q . . . 3 V to 26 V) or
Dual Supplies
D
Low Supply-Current Drain Independent of
Supply Voltage . . . 0.7 mA Typ
D
Common-Mode Input Voltage Range
Includes Ground, Allowing Direct Sensing
Near Ground
D
Low Input Bias and Offset Parameters:
Input Offset Voltage . . . 3 mV Typ
A Versions . . . 2 mV Typ
Input Offset Current . . . 2 nA Typ
Input Bias Current . . . 20 nA Typ
A Versions . . . 15 nA Typ
D
Differential Input Voltage Range Equal to
Maximum-Rated Supply Voltage . . .
32 V
(LM2904 and LM2904Q . . .
26 V)
D
Open-Loop Differential Voltage
Amplification . . . 100 V/mV Typ
D
Internal Frequency Compensation
description
These devices consist of two independent, high-gain, frequency-compensated operational amplifiers designed
to operate from a single supply over a wide range of voltages. Operation from split supplies also is possible if
the difference between the two supplies is 3 V to 30 V (3 V to 26 V for the LM2904 and LM2904Q), and V
CC
is at least 1.5 V more positive than the input common-mode voltage. The low supply-current drain is independent
of the magnitude of the supply voltage.
Applications include transducer amplifiers, dc amplification blocks, and all the conventional operational
amplifier circuits that now can be more easily implemented in single-supply-voltage systems. For example,
these devices can be operated directly from the standard 5-V supply used in digital systems and easily provides
the required interface electronics without additional
5-V supplies.
The LM2904Q is manufactured to demanding automotive requirements.
The LM158 and LM158A are characterized for operation over the full military temperature range of 55
C to
125
C. The LM258 and LM258A are characterized for operation from 25
C to 85
C, the LM358 and LM358A
from 0
C to 70
C, and the LM2904 and LM2904Q from 40
C to 125
C.
logic diagram (each amplifier)
IN+
IN
OUT
+
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright
1998, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
2
3
4
8
7
6
5
1OUT
1IN
1IN+
GND
V
CC
2OUT
2IN
2IN+
D, JG, P, OR PW PACKAGE
(TOP VIEW)
3
2 1 20 19
9 10 11 12 13
4
5
6
7
8
18
17
16
15
14
NC
2OUT
NC
2IN
NC
NC
1IN
NC
1IN+
NC
LM158, LM158A . . . FK PACKAGE
(TOP VIEW)
NC
1OUT
NC
NC
NC
NC
GND
NC
CC+
V
2IN+
NC No internal connection
On products compliant to MIL-PRF-38535, all parameters are tested
unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
LM158, LM158A, LM258, LM258A
LM358, LM358A, LM358Y, LM2904, LM2904Q
DUAL OPERATIONAL AMPLIFIERS
SLOS068C JUNE 1976 REVISED JULY 1998
2
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
AVAILABLE OPTIONS
PACKAGED DEVICES
CHIP
TA
VIO(max)
AT 25
C
SMALL
OUTLINE
(D)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(JG)
PLASTIC
DIP
(P)
TSSOP
(PW)
CHIP
FORM
(Y)
0
C to 70
C
7 mV
LM358D
--
--
LM358P
LM358PW
LM358Y
0
C to 70
C
3 mV
--
--
--
LM358AP
--
--
25
C to 85
C
5 mV
LM258D
--
--
LM258P
--
--
25
C to 85
C
3 mV
--
--
--
LM258AP
--
--
40
C to 125
C
7 mV
LM2904D
--
--
LM2904P
LM2904PW
--
40
C to 125
C
7 mV
LM2904QD
--
--
LM2904QP
--
--
55
C to 125
C
5 mV
LM158D
LM158FK
LM158JG
LM158P
--
--
55
C to 125
C
2 mV
--
LM158AFK
LM158AJG
--
--
--
The D package is available taped and reeled. Add the suffix R to the device type (e.g., LM358DR).
The PW package is only available left-end taped and reeled.
schematic (each amplifier)
VCC+
OUT
GND (or VCC)
To Other Amplifier
IN
IN+
6-
A
Current
Regulator
6-
A
Current
Regulator
100-
A
Current
Regulator
50-
A
Current
Regulator
Epi-FET
Diodes
Resistors
Transistors
Capacitors
COMPONENT COUNT
1
2
7
51
2
LM158, LM158A, LM258, LM258A
LM358, LM358A, LM358Y, LM2904, LM2904Q
DUAL OPERATIONAL AMPLIFIERS
SLOS068C JUNE 1976 REVISED JULY 1998
3
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
LM358Y chip information
These chips, when properly assembled, display characteristics similar to the LM358. Thermal compression or
ultrasonic bonding can be used on the doped-aluminum bonding pads. Chips can be mounted with conductive
epoxy or a gold-silicon preform.
Chip Thickness: 15 Typical
Bonding Pads: 4
4 Minimum
TJ(max) = 150
C
Tolerances Are
10%.
All Dimensions Are in Mils.
No Backside Metallization
Pin (4) is Internally Connected to Backside of Chip.
BONDING PAD ASSIGNMENTS
47
57
(7)
(6)
(5)
(8)
(4)
(3)
(2)
(1)
1IN+
1IN
1OUT
+
(2)
(3)
(1)
VCC+
(8)
2OUT
2IN+
VCC
(4)
+
2IN
(5)
(6)
(7)
LM158, LM158A, LM258, LM258A
LM358, LM358A, LM358Y, LM2904, LM2904Q
DUAL OPERATIONAL AMPLIFIERS
SLOS068C JUNE 1976 REVISED JULY 1998
4
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
LM158, LM158A
LM258, LM258A
LM358, LM358A
LM2904
LM2904Q
UNIT
Supply voltage, VCC (see Note 1)
32
26
V
Differential input voltage, VID (see Note 2)
32
26
V
Input voltage, VI (either input)
0.3 to 32
0.3 to 26
V
Duration of output short circuit (one amplifier) to ground
at (or below) 25
C free-air temperature (VCC
15 V) (see Note 3)
Unlimited
Unlimited
Continuous total power dissipation
See Dissipation Rating Table
LM158, LM158A
55 to 125
Operating free air temperature range TA
LM258, LM258A
25 to 85
C
Operating free-air temperature range, TA
LM358, LM358A
0 to 70
C
LM2904, LM2904Q
40 to 125
Storage temperature range, Tstg
65 to 150
65 to 150
C
Case temperature for 60 seconds
FK package
260
C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds
JG package
300
300
C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
D, P, or PW package
260
260
C
NOTES:
1. All voltage values, except differential voltages and VCC specified for measurement of IOS, are with respect to the network ground
terminal.
2. Differential voltages are at IN+ with respect to IN.
3. Short circuits from outputs to VCC can cause excessive heating and eventual destruction.
DISSIPATION RATING TABLE
PACKAGE
TA
25
C
POWER RATING
DERATING FACTOR
ABOVE TA = 25
C
TA = 70
C
POWER RATING
TA = 85
C
POWER RATING
TA = 125
C
POWER RATING
D
725 mW
5.8 mW/
C
464 mW
377 mW
145 mW
FK
1375 mW
11.0 mW/
C
880 mW
715 mW
275 mW
JG
1050 mW
8.4 mW/
C
672 mW
546 mW
210 mW
P
1000 mW
8.0 mW/
C
640 mW
520 mW
200 mW
PW
525 mW
4.2 mW/
C
336 mW
273 mW
LM158, LM158A, LM258, LM258A
LM358, LM358A, LM358Y, LM2904, LM2904Q
DUAL OPERATIONAL AMPLIFIERS
SLOS068C JUNE 1976 REVISED JULY 1998
5
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, V
CC
= 5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
LM158
LM258
LM358
UNIT
A
MIN
TYP
MAX
MIN
TYP
MAX
VIO
Input offset voltage
VCC = 5 V to MAX,
VIC VICR( i )
25
C
3
5
3
7
mV
VIO
Input offset voltage
VIC = VICR(min),
VO = 1.4 V
Full range
7
9
mV
VIO
Average temperature
coefficient of
input offset voltage
Full range
7
7
V/
C
IIO
Input offset current
VO = 1 4 V
25
C
2
30
2
50
nA
IIO
Input offset current
VO = 1.4 V
Full range
100
150
nA
IIO
Average temperature
coefficient of
input offset current
Full range
10
10
pA/
C
IIB
Input bias current
VO = 1 4 V
25
C
20
150
20
250
nA
IIB
Input bias current
VO = 1.4 V
Full range
300
500
nA
VICR
Common-mode
VCC = 5 V to MAX
25
C
0 to
VCC1.5
0 to
VCC1.5
V
VICR
input voltage range
VCC = 5 V to MAX
Full range
0 to
VCC2
0 to
VCC2
V
RL
2 k
25
C
VCC1.5
VCC1.5
VOH
High-level
RL
10 k
25
C
V
VOH
g
output voltage
VCC = MAX
RL = 2 k
Full range
26
26
V
VCC = MAX
RL
10 k
Full range
27
28
27
28
VOL
Low-level
output voltage
RL
10 k
Full range
5
20
5
20
mV
AVD
Large-signal
differential
VCC = 15 V,
VO 1 V to 11 V
25
C
50
100
25
100
V/mV
AVD
differential
voltage amplification
VO = 1 V to 11 V,
RL =
2 k
Full range
25
15
V/mV
CMRR
Common-mode
rejection ratio
VCC = 5 V to MAX,
VIC = VICR(min)
25
C
70
80
65
80
dB
kSVR
Supply-voltage
rejection ratio
(
VDD/
VIO)
VCC = 5 V to MAX
25
C
65
100
65
100
dB
VO1/VO2
Crosstalk attenuation
f = 1 kHz to 20 kHz
25
C
120
120
dB
VCC = 15 V, VID = 1 V,
25
C
20
30
20
30
CC
,
ID
,
VO = 0
Full range
10
10
mA
IO
Output current
VCC = 15 V, VID = 1 V,
25
C
10
20
10
20
mA
CC
,
ID
,
VO = 15 V
Full range
5
5
VID = 1 V,
VO = 200 mV
25
C
12
30
12
30
A
IOS
Short-circuit
output current
VCC at 5 V, GND at 5 V,
VO = 0
25
C
40
60
40
60
mA
Supply current
VO = 2.5 V,
No load
Full range
0.7
1.2
0.7
1.2
ICC
Supply current
(two amplifiers)
VCC = MAX, VO = 0.5 V,
No load
Full range
1
2
1
2
mA
All characteristics are measured under open-loop conditions with zero common-mode input voltage, unless otherwise specified. MAX VCC for
testing purposes is 26 V for LM 2904 and 30 V for others.
Full range is 55
C to 125
C for LM158, 25
C to 85
C for LM258, 0
C to 70
C for LM358, and 40
C to 125
C for LM2904 and LM2904Q.
All typical values are at TA = 25
C.
PDF 
ZIP