TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
1
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
D
Output Swing Includes Both Supply Rails
D
Low Noise . . . 19 nV/
Hz Typ at f = 1 kHz
D
Low Input Bias Current . . . 1 pA Typ
D
Fully Specified for Both Single-Supply and
Split-Supply Operation
D
Very Low Power . . . 34
A Per Channel Typ
D
Common-Mode Input Voltage Range
Includes Negative Rail
D
Low Input Offset Voltage
850
V Max at T
A
= 25
C
D
Wide Supply Voltage Range
2.7 V to 8 V
D
Macromodel Included
D
Available in Q-Temp Automotive
HighRel Automotive Applications
Configuration Control / Print Support
Qualification to Automotive Standards
description
The TLV2252 and TLV2254 are dual and
quadruple low-voltage operational amplifiers from
Texas Instruments. Both devices exhibit rail-to-rail
output performance for increased dynamic range
in single- or split-supply applications. The
TLV225x family consumes only 34
A of supply
current per channel. This micropower operation
makes them good choices for battery-powered
applications. This family is fully characterized at
3 V and 5 V and is optimized for low-voltage
applications. The noise performance has been
dramatically improved over previous generations
of CMOS amplifiers. The TLV225x has a noise
level of 19 nV/
Hz at 1kHz, four times lower than
competitive micropower solutions.
The TLV225x, exhibiting high input impedance
and low noise, are excellent for small-signal
conditioning for high-impedance sources, such as
piezoelectric transducers. Because of the micro-
power dissipation levels combined with 3-V
operation, these devices work well in hand-held
monitoring and remote-sensing applications. In
addition, the rail-to-rail output feature with single or split supplies makes this family a great choice when
interfacing with analog-to-digital converters (ADCs). For precision applications, the TLV225xA family is
available and has a maximum input offset voltage of 850
V.
The TLV2252/4 also make great upgrades to the TLV2322/4 in standard designs. They offer increased output
dynamic range, lower noise voltage, and lower input offset voltage. This enhanced feature set allows them to
be used in a wider range of applications. For applications that require higher output drive and wider input voltage
range, see the TLV2432 and TLV2442 devices. If your design requires single amplifiers, please see the
TLV2211/21/31 family. These devices are single rail-to-rail operational amplifiers in the SOT-23 package. Their
small size and low power consumption, make them ideal for high density, battery-powered equipment.
Copyright
2001, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Advanced LinCMOS is a trademark of Texas Instruments.
Figure 1
High-Level Output V
oltage V
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
V
OH
| IOH | High-Level Output Current
A
2
1.5
1
0
0
200
400
2.5
3
600
800
TA = 25
C
TA = 85
C
0.5
TA = 125
C
VDD = 3 V
TA = 40
C
On products compliant to MIL-PRF-38535, all parameters are tested
unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
2
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2252 AVAILABLE OPTIONS
PACKAGED DEVICES
TA
VIOmax
AT 25
C
SMALL
OUTLINE
(D)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(JG)
PLASTIC
DIP
(P)
TSSOP
(PW)
CERAMIC
FLATPACK
(U)
40
C to 125
C
850
V
TLV2252AID
--
--
TLV2252AIP
TLV2252AIPWLE
--
40
C to 125
C
1500
V
TLV2252ID
--
--
TLV2252IP
--
--
40
C to 125
C
850
V
TLV2252AQD
--
--
--
--
--
40
C to 125
C
1500
V
TLV2252QD
--
--
--
--
--
55
C to 125
C
850
V
1500
V
--
--
TLV2252AMFK
TLV2252MFK
TLV2252AMJG
TLV2252MJG
--
--
--
--
TLV2252AMU
TLV2252MU
The D packages are available taped and reeled. Add R suffix to device type (e.g., TLV2252CDR).
The PW package is available only left-end taped and reeled.
Chips are tested at 25
C.
TLV2254 AVAILABLE OPTIONS
PACKAGED DEVICES
TA
VIOmax
AT 25
C
SMALL
OUTLINE
(D)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(J)
PLASTIC
DIP
(N)
TSSOP
(PW)
CERAMIC
FLATPACK
(W)
40
C to 125
C
850
V
TLV2254AID
--
--
TLV2254AIN
TLV2254AIPWLE
--
40
C to 125
C
1500
V
TLV2254ID
--
--
TLV2254IN
--
--
40
C to 125
C
850
V
TLV2254AQD
--
--
--
--
--
40
C to 125
C
1500
V
TLV2254QD
--
--
--
--
--
55
C to 125
C
850
V
1500
V
--
--
TLV2254AMFK
TLV2254MFK
TLV2254AMJ
TLV2254MJ
--
--
--
--
TLV2254AMW
TLV2254MW
The D packages are available taped and reeled. Add R suffix to device type (e.g., TLV2254CDR).
The PW package is available only left-end taped and reeled.
Chips are tested at 25
C.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
3
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2252M, TLV2252AM . . . JG PACKAGE
(TOP VIEW)
TLV2252I, TLV2252AI
TLV2252Q, TLV2252AQ
D, P, OR PW PACKAGE
(TOP VIEW)
1
2
3
4
8
7
6
5
1OUT
1IN
1IN +
V
DD
/GND
V
DD +
2OUT
2IN
2IN +
NC
V
CC
+
2OUT
2IN
2IN +
NC
1OUT
1IN
1IN +
V
CC
/GND
1
2
3
4
5
10
9
8
7
6
TLV2252M, TLV2252AM . . . U PACKAGE
(TOP VIEW)
1
2
3
4
8
7
6
5
1OUT
1IN
1IN +
V
DD
/GND
V
DD +
2OUT
2IN
2IN +
3
2
1 20 19
9 10 11 12 13
4
5
6
7
8
18
17
16
15
14
NC
2OUT
NC
2IN
NC
NC
1IN
NC
1IN +
NC
NC
1OUT
NC
2IN+
NC
NC
NC
NC
V
DD+
V
DD
/GND
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1OUT
1IN
1IN +
V
DD +
2IN +
2IN
2OUT
4OUT
4IN
4IN +
V
DD
/ GND
3IN +
3IN
3OUT
TLV2254I, TLV2254AI, TLV2254Q, TLV2254AQ . . . D OR N PACKAGE
TLV2254M, TLV2254AM . . . J OR W PACKAGE
(TOP VIEW)
TLV2254I, TLV2254AI . . . PW PACKAGE
(TOP VIEW)
1
14
8
7
4OUT
4IN
4IN +
V
DD
/ GND
3IN +
3IN
3OUT
1OUT
1IN
1IN +
V
DD+
2IN +
2IN
2OUT
3
2
1 20 19
9 10 11 12 13
4
5
6
7
8
18
17
16
15
14
4IN+
NC
V
DD
/ GND
NC
3IN+
1IN+
NC
V
DD+
NC
2IN+
1IN
1OUT
NC
3OUT
3IN
4IN
2IN
NC
4OUT
2OUT
TLV2252M, TLV2252AM . . . FK PACKAGE
(TOP VIEW)
TLV2254M, TLV2254AM . . . FK PACKAGE
(TOP VIEW)
T
emp
l
ate
R
e
l
ease
D
ate:
7
11
94
TL
V225x, TL
V2252xA
VER
Y
LOW
-POWER OPERA
TIONAL
AMPLIFIERS
SLOS185C
FEBRUAR
Y
1997
REVISED MARCH 2001
Advanced LinCMOS
RAIL-T
O-RAIL
4
POST
OFFICE BOX 655303 DALLAS,
TEXAS
75265
equivalent schematic (each amplifier)
Q3
Q6
Q9
Q12
Q14
Q16
Q2
Q5
Q7
Q8
Q10
Q11
D1
Q17
Q15
Q13
Q4
Q1
R5
C1
VDD +
IN +
IN
R3
R4
R1
R2
OUT
VDD / GND
R6
ACTUAL DEVICE COMPONENT COUNT
COMPONENT
TLV2252
TLV2254
Transistors
38
76
Resistors
30
56
Diodes
9
18
Capacitors
3
6
Includes both amplifiers and all ESD, bias, and trim circuitry
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
5
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage, V
DD
(see Note 1)
16 V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential input voltage, V
ID
(see Note 2)
V
DD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range, V
I
(any input, see Note 1)
V
DD
0.3 V to V
DD+
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input current, I
I
(each input)
5 mA
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output current, I
O
50 mA
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total current into V
DD +
50 mA
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total current out of V
DD
50 mA
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Duration of short-circuit current (at or below) 25
C (see Note 3)
unlimited
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation
See Dissipation Rating Table
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, T
A
: I Suffix
40
C to 125
C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Q Suffix
40
C to 125
C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
M Suffix
55
C to 125
C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, T
stg
65
C to 150
C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, N, P, and PW packages
260
C
. . . . . . .
J, JG, U, and W packages
300
C
. . . . . . .
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES:
1. All voltage values, except differential voltages, are with respect to VDD .
2. Differential voltages are at the noninverting input with respect to the inverting input. Excessive current flows when input is brought
below VDD 0.3 V.
3. The output may be shorted to either supply. Temperature and /or supply voltages must be limited to ensure that the maximum
dissipation rating is not exceeded.
DISSIPATION RATING TABLE
PACKAGE
TA
25
C
DERATING FACTOR
TA = 85
C
TA = 125
C
PACKAGE
A
POWER RATING
ABOVE TA = 25
C
A
POWER RATING
A
POWER RATING
D8
725 mW
5.8 mW/
C
377 mW
145 mW
D14
950 mW
7.6 mW/
C
494 mW
190 mW
FK
1375 mW
11.0 mW/
C
715 mW
275 mW
J
1375 mW
11.0 mW/
C
715 mW
275 mW
JG
1050 mW
8.4 mW/
C
546 mW
210 mW
N
1150 mW
9.2 mW/
C
598 mW
230 mW
P
1000 mW
8.0 mW/
C
520 mW
200 mW
PW8
525 mW
4.2 mW/
C
273 mW
105 mW
PW14
700 mW
5.6 mW/
C
364 mW
140 mW
U
700 mW
5.5 mW/
C
370 mW
150 mW
W
700 mW
5.5 mW/
C
370 mW
150 mW
recommended operating conditions
TLV225xI
TLV225xQ
TLV225xM
UNIT
MIN
MAX
MIN
MAX
MIN
MAX
UNIT
Supply voltage, VDD
(see Note 1)
2.7
16
2.7
16
2.7
16
V
Input voltage range, VI
VDD
VDD + 1.3
VDD
VDD + 1.3
VDD
VDD + 1.3
V
Common-mode input voltage, VIC
VDD
VDD + 1.3
VDD
VDD + 1.3
VDD
VDD + 1.3
V
Operating free-air temperature, TA
40
125
40
125
55
125
C
NOTE 1: All voltage values, except differential voltages, are with respect to VDD .
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
6
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2252I electrical characteristics at specified free-air temperature, V
DD
= 3 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA
TLV2252I
TLV2252AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
VIO
Input offset voltage
V
V
V
25
C
200
1500
200
850
V
VIO
In ut offset voltage
V
V
V
Full range
1750
1000
V
VIO
Temperature coefficient
V
V
V
25
C
0 5
0 5
V/
C
VIO
of input offset voltage
V
V
V
to 85
C
0.5
0.5
V/
C
Input offset voltage
long-term drift (see
Note 4)
V
1 5 V
V
0
25
C
0.003
0.003
V/mo
VDD
=
1.5 V,
VO = 0
VIC = 0,
RS = 50
25
C
0.5
60
0.5
60
IIO
Input offset current
VO = 0,
RS = 50
40
C
to 85
C
150
150
pA
Full range
1000
1000
25
C
1
60
1
60
IIB
Input bias current
40
C
to 85
C
150
150
pA
Full range
1000
1000
0
0.3
0
0.3
25
C
to
to
to
to
VICR
Common-mode input
RS = 50
|
VIO
|
5 mV
2
2.2
2
2.2
V
VICR
voltage range
RS = 50
,
|
VIO
|
5 mV
0
0
V
Full range
to
to
1.7
1.7
IOH = 20
A
25
C
2.98
2.98
VOH
High-level output
IOH = 75
A
25
C
2.9
2.9
V
VOH
g
voltage
IOH = 75
A
Full range
2.8
2.8
V
IOH = 150
A
25
C
2.8
2.8
VIC = 1 5 V
IOL = 50
A
25
C
10
10
VIC = 1.5 V,
IOL = 50
A
Full range
80
80
VOL
Low-level output
VIC = 1 5 V
IOL = 500
A
25
C
100
100
mV
VOL
voltage
VIC = 1.5 V,
IOL = 500
A
Full range
150
150
mV
VIC = 1 5 V
IOL = 1
m
A
25
C
200
200
VIC = 1.5 V,
IOL = 1
m
A
Full range
300
300
Large signal differential
V
1 5 V
RL 100 k
25
C
100
250
100
250
AVD
Large-signal differential
voltage amplification
VIC = 1.5 V,
VO = 1 V to 2 V
RL = 100 k
Full range
10
10
V/mV
voltage am lification
VO = 1 V to 2 V
RL = 1 M
25
C
800
800
ri(d)
Differential input
resistance
25
C
1012
1012
ri(c)
Common-mode input
resistance
25
C
1012
1012
ci(c)
Common-mode input
capacitance
f = 10 kHz,
P package
25
C
8
8
pF
zo
Closed-loop output
impedance
f = 25 kHz,
AV = 10
25
C
220
220
CMRR
Common-mode
VIC = 0 to 1.7 V,
25
C
65
75
65
77
dB
CMRR
rejection ratio
IC
VO = 1.5 V,
RS = 50
Full range
60
60
dB
Full range is 40
C to 125
C.
Referenced to 1.5 V
NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150
C extrapolated
to TA = 25
C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
7
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2252I electrical characteristics at specified free-air temperature, V
DD
= 3 V (unless otherwise
noted) (continued)
PARAMETER
TEST CONDITIONS
TA
TLV2252I
TLV2252AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
kSVR
Supply voltage
rejection ratio
VDD = 2.7 V to 8 V,
25
C
80
95
80
100
dB
kSVR
rejection ratio
(
VDD /
VIO)
DD
VIC = VDD /2, No
load
Full range
80
80
dB
IDD
Supply current
VO = 1 5 V
No load
25
C
68
125
68
125
A
IDD
Su
ly current
VO = 1.5 V,
No load
Full range
150
150
A
Full range is 40
C to 125
C.
TLV2252I operating characteristics at specified free-air temperature, V
DD
= 3 V
PARAMETER
TEST CONDITIONS
TA
TLV2252I
TLV2252AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
25
C
0 07
0 1
0 07
0 1
VO = 1.1 V to 1.9 V,
25
C
0.07
0.1
0.07
0.1
SR
Slew rate at unity gain
O
RL = 100 k
,
C
100 F
Full
0 05
0 05
V/
s
CL = 100 pF
range
0.05
0.05
V
Equivalent input noise
f = 10 Hz
25
C
35
35
nV/
Hz
Vn
q
voltage
f = 1 kHz
25
C
19
19
nV/
Hz
VN(PP)
Peak-to-peak
equivalent input noise
f = 0.1 Hz to 1 Hz
25
C
0.6
0.6
V
VN(PP)
equivalent input noise
voltage
f = 0.1 Hz to 10 Hz
25
C
1.1
1.1
V
In
Equivalent input noise
current
25
C
0.6
0.6
fA /
Hz
Gain bandwidth product
f = 1 kHz,
RL = 50 k
,
25
C
0 187
0 187
MHz
Gain-bandwidth product
f 1 kHz,
CL = 100 pF
RL 50 k
,
25
C
0.187
0.187
MHz
BOM
Maximum output-swing
VO(PP) = 1 V,
AV = 1,
25
C
60
60
kHz
BOM
g
bandwidth
O(PP)
,
RL = 50 k
,
V
,
CL = 100 pF
25
C
60
60
kHz
m
Phase margin at unity
gain
RL = 50 k
,
CL = 100 pF
25
C
63
63
Gain margin
L
,
L
25
C
15
15
dB
Full range is 40
C to 125
C.
Referenced to 1.5 V
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
8
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2252I electrical characteristics at specified free-air temperature, V
DD
= 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA
TLV2252I
TLV2252AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
VIO
Input offset voltage
V
V
V
25
C
200
1500
200
850
V
VIO
Input offset voltage
V
V
V
Full range
1750
1000
V
VIO
Temperature coefficient
V
V
V
25
C
0 5
0 5
V/
C
VIO
of input offset voltage
V
V
V
to 85
C
0.5
0.5
V/
C
Input offset voltage long-
term drift (see Note 4)
V
V
V
25
C
0.003
0.003
V/mo
VDD
=
2.5 V,
VIC = 0,
25
C
0.5
60
0.5
60
IIO
Input offset current
VO = 0,
IC
RS = 50
40
C
to 85
C
150
150
pA
Full range
1000
1000
25
C
1
60
1
60
IIB
Input bias current
40
C
to 85
C
150
150
pA
Full range
1000
1000
VICR
Common-mode input
|
VIO
|
5 mV
RS = 50
25
C
0
to
4
0.3
to
4.2
0
to
4
0.3
to
4.2
V
VICR
voltage range
|
VIO
|
5 mV,
RS = 50
Full range
0
to
3.5
0
to
3.5
V
IOH = 20
A
25
C
4.98
4.98
VOH
High level output voltage
IOH = 75
A
25
C
4.9
4.94
4.9
4.94
V
VOH
High-level output voltage
IOH = 75
A
Full range
4.8
4.8
V
IOH = 150
A
25
C
4.8
4.88
4.8
4.88
VIC = 2 5 V
IOL = 50
A
25
C
0.01
0.01
VIC = 2.5 V,
IOL = 50
A
Full range
0.06
0.06
VOL
Low level output voltage
VIC = 2 5 V
IOL = 500
A
25
C
0.09
0.15
0.09
0.15
V
VOL
Low-level output voltage
VIC = 2.5 V,
IOL = 500
A
Full range
0.15
0.15
V
VIC = 2 5 V
IOL = 1
m
A
25
C
0.2
0.3
0.2
0.3
VIC = 2.5 V,
IOL = 1
m
A
Full range
0.3
0.3
L
i
l diff
ti l
V
2 5 V
RL 100 k
25
C
100
350
100
350
AVD
Large-signal differential
voltage amplification
VIC = 2.5 V,
VO = 1 V to 4 V
RL = 100 k
Full range
10
10
V/mV
voltage am lification
VO = 1 V to 4 V
RL = 1 M
25
C
1700
1700
ri(d)
Differential input
resistance
25
C
1012
1012
ri(c)
Common-mode input
resistance
25
C
1012
1012
ci(c)
Common-mode input
capacitance
f = 10 kHz,
P package
25
C
8
8
pF
zo
Closed-loop output
impedance
f = 25 kHz,
AV = 10
25
C
200
200
CMRR
Common-mode rejection
VIC = 0 to 2.7 V,
VO = 2.5 V,
25
C
70
83
70
83
dB
CMRR
j
ratio
IC
RS = 50
O
Full range
70
70
dB
Full range is 40
C to 125
C.
Referenced to 2.5 V
NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150
C extrapolated
to TA = 25
C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
9
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2252I electrical characteristics at specified free-air temperature, V
DD
= 5 V (unless otherwise
noted) (continued)
PARAMETER
TEST CONDITIONS
TA
TLV2252I
TLV2252AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
kSVR
Supply voltage rejection
VDD = 4.4 V to 8 V,
25
C
80
95
80
95
dB
kSVR
y
g
j
ratio (
VDD /
VIO)
DD
VIC = VDD /2,
No load
Full range
80
80
dB
IDD
Supply current
VO = 2 5 V
No load
25
C
70
125
70
125
A
IDD
Su
ly current
VO = 2.5 V,
No load
Full range
150
150
A
Full range is 40
C to 125
C.
TLV2252I operating characteristics at specified free-air temperature, V
DD
= 5 V
PARAMETER
TEST CONDITIONS
TA
TLV2252I
TLV2252AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
25
C
0 07
0 12
0 07
0 12
VO = 1 5 V to 3 5 V
RL = 100 k
25
C
0.07
0.12
0.07
0.12
SR
Slew rate at unity gain
VO = 1.5 V to 3.5 V,
CL = 100 pF
RL = 100 k
,
Full
0 05
0 05
V/
s
CL = 100 F
range
0.05
0.05
V
Equivalent input noise
f = 10 Hz
25
C
36
36
nV/
Hz
Vn
q
voltage
f = 1 kHz
25
C
19
19
nV/
Hz
VN(PP)
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz
25
C
0.7
0.7
V
VN(PP)
equivalent input
noise voltage
f = 0.1 Hz to 10 Hz
25
C
1.1
1.1
V
In
Equivalent input noise
current
25
C
0.6
0.6
fA /
Hz
THD + N
Total harmonic
VO = 0.5 V to 2.5 V,
f = 20 kHz
AV = 1
25
C
0.2%
0.2%
THD + N
distortion plus noise
f = 20 kHz,
RL = 50 k
AV = 10
25
C
1%
1%
Gain-bandwidth
f = 50 kHz,
RL = 50 k
,
25
C
0 2
0 2
MHz
product
,
CL = 100 pF
L
,
25
C
0.2
0.2
MHz
BOM
Maximum output-swing
VO(PP) = 2 V,
AV = 1,
25
C
30
30
kHz
BOM
g
bandwidth
O(PP)
,
RL = 50 k
,
V
,
CL = 100 pF
25
C
30
30
kHz
m
Phase margin at unity
gain
RL = 50 k
,
CL = 100 pF
25
C
63
63
Gain margin
L
,
L
25
C
15
15
dB
Full range is 40
C to 125
C.
Referenced to 2.5 V
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
10
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2254I electrical characteristics at specified free-air temperature, V
DD
= 3 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA
TLV2254I
TLV2254AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
VIO
Input offset voltage
25
C
200
1500
200
850
V
VIO
Input offset voltage
Full range
1750
1000
V
VIO
Temperature
coefficient of input
25
C
0 5
0 5
V/
C
VIO
coefficient of input
offset voltage
to 85
C
0.5
0.5
V/
C
Input offset voltage
long-term drift
(see Note 4)
VDD
=
1.5 V,
VIC = 0,
25
C
0.003
0.003
V/mo
VDD
1.5 V,
VO = 0,
VIC 0,
RS = 50
25
C
0.5
60
0.5
60
IIO
Input offset current
40
C
to 85
C
150
150
pA
Full range
1000
1000
25
C
1
60
1
60
IIB
Input bias current
40
C
to 85
C
150
150
pA
Full range
1000
1000
25
C
0
0.3
0
0.3
VICR
Common-mode input
RS = 50
,
|
VIO
|
5 mV
25
C
to 2
to 2.2
to 2
to 2.2
V
VICR
voltage range
S
|
VIO
|
5 mV
Full range
0
0
V
Full range
to 1.7
to 1.7
IOH = 20
A
25
C
2.98
2.98
VOH
High-level output
IOH = 75
A
25
C
2.9
2.9
V
VOH
g
voltage
IOH = 75
A
Full range
2.8
2.8
V
IOH = 150
A
25
C
2.8
2.8
VIC = 1 5 V
IOL = 50
A
25
C
10
10
VIC = 1.5 V,
IOL = 50
A
Full range
80
80
VOL
Low-level output
VIC = 1 5 V
IOL = 500
A
25
C
100
100
mV
VOL
voltage
VIC = 1.5 V,
IOL = 500
A
Full range
150
150
mV
VIC = 1 5 V
IOL
1
m
A
25
C
200
200
VIC = 1.5 V,
IOL = 1
m
A
Full range
300
300
Large-signal
V
1 5 V
RL = 100 k
25
C
100
225
100
225
AVD
g
g
differential voltage
VIC = 1.5 V,
VO = 1 V to 2 V
RL = 100 k
Full range
10
10
V/mV
amplification
VO = 1 V to 2 V
RL = 1 M
25
C
800
800
ri(d)
Differential input
resistance
25
C
1012
1012
ri(c)
Common-mode input
resistance
25
C
1012
1012
ci(c)
Common-mode input
capacitance
f = 10 kHz,
N package
25
C
8
8
pF
zo
Closed-loop output
impedance
f = 25 kHz,
AV = 10
25
C
220
220
CMRR
Common-mode
VIC = 0 to 1.7 V, VO = 1.5 V,
25
C
65
75
65
77
dB
CMRR
rejection ratio
IC
RS = 50
O
Full range
60
60
dB
Full range is 40
C to 125
C.
Referenced to 1.5 V
NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150
C extrapolated
to TA = 25
C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
11
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2254I electrical characteristics at specified free-air temperature, V
DD
= 3 V (unless otherwise
noted) (continued)
PARAMETER
TEST CONDITIONS
TA
TLV2254I
TLV2254AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
kSVR
Supply voltage
rejection ratio
VDD = 2.7 V to 8 V,
25
C
80
95
80
100
dB
kSVR
rejection ratio
(
VDD /
VIO)
DD
VIC = VDD /2, No
load
Full range
80
80
dB
IDD
Supply current
VO = 1 5 V
No load
25
C
135
250
135
250
A
IDD
y
(four amplifiers)
VO = 1.5 V,
No load
Full range
300
300
A
Full range is 40
C to 125
C.
TLV2254I operating characteristics at specified free-air temperature, V
DD
= 3 V
PARAMETER
TEST CONDITIONS
TA
TLV2254I
TLV2254AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
VO = 0 7 V to 1 7 V
25
C
0 07
0 1
0 07
0 1
SR
Slew rate at unity gain
VO = 0.7 V to 1.7 V,
RL = 100 k
25
C
0.07
0.1
0.07
0.1
V/
s
SR
Slew rate at unity gain
RL = 100 k
,
C
100 F
Full range
0 05
0 05
V/
s
CL = 100 pF
Full range
0.05
0.05
V
Equivalent input noise voltage
f = 10 Hz
25
C
35
35
nV/
Hz
Vn
Equivalent input noise voltage
f = 1 kHz
25
C
19
19
nV/
Hz
VN(PP)
Peak-to-peak equivalent input
f = 0.1 Hz to 1 Hz
25
C
0.6
0.6
V
VN(PP)
q
noise voltage
f = 0.1 Hz to 10 Hz
25
C
1.1
1.1
V
In
Equivalent input noise current
25
C
0.6
0.6
fA /
Hz
Gain bandwidth product
f = 1 kHz,
RL 50 k
25
C
0 187
0 187
MHz
Gain-bandwidth product
RL = 50 k
,
CL = 100 pF
25
C
0.187
0.187
MHz
BOM
Maximum output-swing
VO(PP) = 1 V,
AV = 1,
25
C
60
60
kHz
BOM
g
bandwidth
V
,
RL = 50 k
,
CL = 100 pF
25
C
60
60
kHz
m
Phase margin at unity gain
RL = 50 k
,
25
C
63
63
Gain margin
L
,
CL = 100 pF
25
C
15
15
dB
Full range is 40
C to 85
C.
Referenced to 1.5 V
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
12
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2254I electrical characteristics at specified free-air temperature, V
DD
= 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA
TLV2254I
TLV2254AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
VIO
Input offset voltage
25
C
200
1500
200
850
V
VIO
Input offset voltage
Full range
1750
1000
V
VIO
Temperature
coefficient of input
25
C
0 5
0 5
V/
C
VIO
coefficient of input
offset voltage
to 85
C
0.5
0.5
V/
C
Input offset voltage
long-term drift
(see Note 4)
VDD
=
2.5 V,
VIC = 0,
25
C
0.003
0.003
V/mo
VDD
2.5 V,
VO = 0,
VIC 0,
RS = 50
25
C
0.5
60
0.5
60
IIO
Input offset current
40
C
to 85
C
150
150
pA
Full range
1000
1000
25
C
1
60
1
60
IIB
Input bias current
40
C
to 85
C
150
150
pA
Full range
1000
1000
25
C
0
0.3
0
0.3
VICR
Common-mode input
|
VIO
|
5 mV
RS = 50
25
C
to 4
to 4.2
to 4
to 4.2
V
VICR
voltage range
|
VIO
|
5 mV,
RS = 50
Full range
0
0
V
Full range
to 3.5
to 3.5
IOH = 20
A
25
C
4.98
4.98
VOH
High-level output
IOH = 75
A
25
C
4.9
4.94
4.9
4.94
V
VOH
g
voltage
IOH = 75
A
Full range
4.8
4.8
V
IOH = 150
A
25
C
4.8
4.88
4.8
4.88
VIC = 2 5 V
IOL = 50
A
25
C
0.01
0.01
VIC = 2.5 V,
IOL = 50
A
Full range
0.06
0.06
VOL
Low-level output
VIC = 2 5 V
IOL = 500
A
25
C
0.09
0.15
0.09
0.15
V
VOL
voltage
VIC = 2.5 V,
IOL = 500
A
Full range
0.15
0.15
V
VIC = 2 5 V
IOL
1
m
A
25
C
0.2
0.3
0.2
0.3
VIC = 2.5 V,
IOL = 1
m
A
Full range
0.3
0.3
Large-signal
V
2 5 V
RL 100 k
25
C
100
350
100
350
AVD
Large signal
differential voltage
VIC = 2.5 V,
VO = 1 V to 4 V
RL = 100 k
Full range
10
10
V/mV
VD
amplification
VO = 1 V to 4 V
RL = 1 M
25
C
1700
1700
ri(d)
Differential input
resistance
25
C
1012
1012
ri(c)
Common-mode input
resistance
25
C
1012
1012
ci(c)
Common-mode input
capacitance
f = 10 kHz,
N package
25
C
8
8
pF
zo
Closed-loop output
impedance
f = 25 kHz,
AV = 10
25
C
200
200
CMRR
Common-mode
VIC = 0 to 2.7 V, VO = 2.5 V,
25
C
70
83
70
83
dB
CMRR
rejection ratio
IC
,
RS = 50
O
,
Full range
70
70
dB
Full range is 40
C to 125
C.
Referenced to 2.5 V
NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150
C extrapolated
to TA = 25
C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
13
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2254I electrical characteristics at specified free-air temperature, V
DD
= 5 V (unless otherwise
noted) (continued)
PARAMETER
TEST CONDITIONS
TA
TLV2254I
TLV2254AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
kSVR
Supply voltage
rejection ratio
VDD = 4.4 V to 8 V,
25
C
80
95
80
95
dB
kSVR
rejection ratio
(
VDD /
VIO)
DD
VIC = VDD /2, No
load
Full range
80
80
dB
IDD
Supply current
VO = 2 5 V
No load
25
C
140
250
140
250
A
IDD
y
(four amplifiers)
VO = 2.5 V,
No load
Full range
300
300
A
Full range is 40
C to 125
C.
TLV2254I operating characteristics at specified free-air temperature, V
DD
= 5 V
PARAMETER
TEST CONDITIONS
T
TLV2254I
TLV2254AI
UNIT
PARAMETER
TEST CONDITIONS
TA
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
Slew rate at unity
V
1 4 V t 2 6 V
R
100 k
25
C
0.07
0.12
0.07
0.12
SR
Slew rate at unity
gain
VO = 1.4 V to 2.6 V,
CL = 100 pF
RL = 100 k
,
Full
range
0.05
0.05
V/
s
V
Equivalent input
f = 10 Hz
25
C
36
36
nV/
Hz
Vn
q
noise voltage
f = 1 kHz
25
C
19
19
nV/
Hz
VN(PP)
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz
25
C
0.7
0.7
V
VN(PP)
equivalent input
noise voltage
f = 0.1 Hz to 10 Hz
25
C
1.1
1.1
V
In
Equivalent input
noise current
25
C
0.6
0.6
fA /
Hz
THD + N
Total harmonic
distortion plus
VO = 0.5 V to 2.5 V,
f = 20 kHz
AV = 1
25
C
0.2%
0.2%
THD + N
distortion plus
noise
f = 20 kHz,
RL = 50 k
AV = 10
25
C
1%
1%
Gain-bandwidth
f = 50 kHz,
RL = 50 k
,
25
C
0 2
0 2
MHz
product
,
CL = 100 pF
L
,
25
C
0.2
0.2
MHz
BOM
Maximum output-
VO(PP) = 2 V,
AV = 1,
25
C
30
30
kHz
BOM
swing bandwidth
O(PP)
,
RL = 50 k
,
V
,
CL = 100 pF
25
C
30
30
kHz
m
Phase margin at
unity gain
RL = 50 k
,
CL = 100 pF
25
C
63
63
Gain margin
L
,
L
25
C
15
15
dB
Full range is 40
C to 125
C.
Referenced to 2.5 V
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
14
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2252Q, and TLV2252M electrical characteristics at specified free-air temperature, V
DD
= 3 V
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
TLV2252Q,
TLV2252M
TLV2252AQ,
TLV2252AM
UNIT
A
MIN
TYP
MAX
MIN
TYP
MAX
VIO
Input offset voltage
V
V
V
25
C
200
1500
200
850
V
VIO
In ut offset voltage
V
V
V
Full range
1750
1000
V
VIO
Temperature coefficient
V
V
V
25
C
0 5
0 5
V/
C
VIO
of input offset voltage
V
V
V
to 85
C
0.5
0.5
V/
C
Input offset voltage
long-term drift
(see Note 4)
VDD
=
1.5 V,
VO = 0,
VIC = 0,
RS = 50
25
C
0.003
0.003
V/mo
IIO
Input offset current
25
C
0.5
60
0.5
60
pA
IIO
In ut offset current
125
C
1000
1000
A
IIB
Input bias current
25
C
1
60
1
60
pA
IIB
In ut bias current
125
C
1000
1000
A
0
0.3
0
0.3
25
C
to
to
to
to
VICR
Common-mode input
RS = 50
|
VIO
|
5 mV
2
2.2
2
2.2
V
VICR
voltage range
RS = 50
,
|
VIO
|
5 mV
0
0
V
Full range
to
to
1.7
1.7
IOH = 20
A
25
C
2.98
2.98
VOH
High-level output
IOH = 75
A
25
C
2.9
2.9
V
VOH
g
voltage
IOH = 75
A
Full range
2.8
2.8
V
IOH = 150
A
25
C
2.8
2.8
VIC = 1.5 V,
IOL = 50
A
25
C
10
10
Low level output
VIC = 1 5 V
IOL = 500
A
25
C
100
150
100
150
VOL
Low-level output
voltage
VIC = 1.5 V,
IOL = 500
A
Full range
165
165
mV
voltage
VIC = 1 5 V
IOL = 1
m
A
25
C
200
300
200
300
VIC = 1.5 V,
IOL = 1
m
A
Full range
300
300
Large signal differential
V
1 5 V
RL 100 k
25
C
100
250
100
250
AVD
Large-signal differential
voltage amplification
VIC = 1.5 V,
VO = 1 V to 2 V
RL = 100 k
Full range
10
10
V/mV
voltage am lification
VO = 1 V to 2 V
RL = 1 M
25
C
800
800
ri(d)
Differential input
resistance
25
C
1012
1012
ri(c)
Common-mode input
resistance
25
C
1012
1012
ci(c)
Common-mode input
capacitance
f = 10 kHz,
P package
25
C
8
8
pF
zo
Closed-loop output
impedance
f = 25 kHz,
AV = 10
25
C
220
220
CMRR
Common-mode rejection
VIC = 0 to 1.7 V, VO = 1.5 V,
25
C
65
75
65
77
dB
CMRR
j
ratio
IC
RS = 50
O
Full range
60
60
dB
kSVR
Supply voltage rejection
VDD = 2.7 V to 8 V,
25
C
80
95
80
100
dB
kSVR
y
g
j
ratio (
VDD /
VIO)
DD
VIC = VDD /2, No
load
Full range
80
80
dB
IDD
Supply current
VO = 1 5 V
No load
25
C
68
125
68
125
A
IDD
Supply current
VO = 1.5 V,
No load
Full range
150
150
A
Full range is 40
C to 125
C for Q level part, 55
C to 125
C for M level part.
Referenced to 1.5 V
NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150
C extrapolated
to TA = 25
C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
15
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2252Q, and TLV2252M operating characteristics at specified free-air temperature, V
DD
= 3 V
PARAMETER
TEST CONDITIONS
TA
TLV2252Q,
TLV2252M
TLV2252AQ,
TLV2252AM
UNIT
A
MIN
TYP
MAX
MIN
TYP
MAX
25
C
0 07
0 1
0 07
0 1
VO = 0 8 V to 1 4 V
RL = 100 k
25
C
0.07
0.1
0.07
0.1
SR
Slew rate at unity gain
VO = 0.8 V to 1.4 V,
CL = 100 pF
RL = 100 k
,
Full
0 05
0 05
V/
s
CL = 100 F
range
0.05
0.05
V
Equivalent input noise
f = 10 Hz
25
C
35
35
nV/
Hz
Vn
q
voltage
f = 1 kHz
25
C
19
19
nV/
Hz
VN(PP)
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz
25
C
0.6
0.6
V
VN(PP) equivalent input
noise voltage
f = 0.1 Hz to 10 Hz
25
C
1.1
1.1
V
In
Equivalent input noise
current
25
C
0.6
0.6
fA /
Hz
Gain-bandwidth
f = 1 kHz,
RL = 50 k
,
25
C
0 187
0 187
MHz
product
f 1 kHz,
CL = 100 pF
RL 50 k
,
25
C
0.187
0.187
MHz
BOM
Maximum
output swing
VO(PP) = 1 V,
AV = 1,
25
C
60
60
kHz
BOM
output-swing
bandwidth
O(PP)
,
RL = 50 k
,
V
,
CL = 100 pF
25
C
60
60
kHz
m
Phase margin at unity
gain
RL = 50 k
,
CL = 100 pF
25
C
63
63
Gain margin
L
,
L
25
C
15
15
dB
Full range is 40
C to 125
C for Q level part, 55
C to 125
C for M level part.
Referenced to 1.5 V
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
16
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2252Q, and TLV2252M electrical characteristics at specified free-air temperature, V
DD
= 5 V
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
TLV2252Q,
TLV2252M
TLV2252AQ,
TLV2252AM
UNIT
A
MIN
TYP
MAX
MIN
TYP
MAX
VIO
Input offset voltage
V
V
V
25
C
200
1500
200
850
V
VIO
Input offset voltage
V
V
V
Full range
1750
1000
V
VIO
Temperature coefficient
V
V
V
25
C
0 5
0 5
V/
C
VIO
of input offset voltage
V
V
V
to 85
C
0.5
0.5
V/
C
Input offset voltage long-
term drift (see Note 4)
VDD
=
2.5 V,
VO = 0,
VIC = 0,
RS = 50
25
C
0.003
0.003
V/mo
IIO
Input offset current
25
C
0.5
60
0.5
60
pA
IIO
Input offset current
125
C
1000
1000
pA
IIB
Input bias current
25
C
1
60
1
60
pA
IIB
Input bias current
125
C
1000
1000
pA
VICR
Common-mode input
|
VIO
|
5 mV
RS = 50
25
C
0
to
4
0.3
to
4.2
0
to
4
0.3
to
4.2
V
VICR
voltage range
|
VIO
|
5 mV,
RS = 50
Full range
0
to
3.5
0
to
3.5
V
IOH = 20
A
25
C
4.98
4.98
VOH
High level output voltage
IOH = 75
A
25
C
4.9
4.94
4.9
4.94
V
VOH
High-level output voltage
IOH = 75
A
Full range
4.8
4.8
V
IOH = 150
A
25
C
4.8
4.88
4.8
4.88
VIC = 2.5 V,
IOL = 50
A
25
C
0.01
0.01
VIC = 2 5 V
IOL = 500
A
25
C
0.09
0.15
0.09
0.15
VOL
Low-level output voltage
VIC = 2.5 V,
IOL = 500
A
Full range
0.15
0.15
V
VIC = 2 5 V
IOL = 1
m
A
25
C
0.2
0.3
0.2
0.3
VIC = 2.5 V,
IOL = 1
m
A
Full range
0.3
0.3
L
i
l diff
ti l
V
2 5 V
RL 100 k
25
C
100
350
100
350
AVD
Large-signal differential
voltage amplification
VIC = 2.5 V,
VO = 1 V to 4 V
RL = 100 k
Full range
10
10
V/mV
voltage am lification
VO = 1 V to 4 V
RL = 1 M
25
C
1700
1700
ri(d)
Differential input
resistance
25
C
1012
1012
ri(c)
Common-mode input
resistance
25
C
1012
1012
ci(c)
Common-mode input
capacitance
f = 10 kHz,
P package
25
C
8
8
pF
zo
Closed-loop output
impedance
f = 25 kHz,
AV = 10
25
C
200
200
CMRR
Common-mode rejection
VIC = 0 to 2.7 V,
25
C
70
83
70
83
dB
CMRR
j
ratio
IC
,
VO = 2.5 V,
RS = 50
Full range
70
70
dB
kSVR
Supply voltage rejection
VDD = 4.4 V to 8 V,
25
C
80
95
80
95
dB
kSVR
y
g
j
ratio (
VDD /
VIO)
DD
VIC = VDD /2, No
load
Full range
80
80
dB
Full range is 40
C to 125
C for Q level part, 55
C to 125
C for M level part.
Referenced to 2.5 V
NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150
C extrapolated
to TA = 25
C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
17
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2252Q, and TLV2252M electrical characteristics at specified free-air temperature, V
DD
= 5 V
(unless otherwise noted) (continued)
PARAMETER
TEST CONDITIONS
TA
TLV2252Q,
TLV2252M
TLV2252AQ,
TLV2252AM
UNIT
A
MIN
TYP
MAX
MIN
TYP
MAX
IDD
Supply current
VO = 2 5 V
No load
25
C
70
125
70
125
A
IDD
Supply current
VO = 2.5 V,
No load
Full range
150
150
A
Full range is 40
C to 125
C for Q level part, 55
C to 125
C for M level part.
TLV2252Q, and TLV2252M operating characteristics at specified free-air temperature, V
DD
= 5 V
PARAMETER
TEST CONDITIONS
TA
TLV2252Q,
TLV2252M
TLV2252AQ,
TLV2252AM
UNIT
A
MIN
TYP
MAX
MIN
TYP
MAX
V
1 25 V t 2 75 V
25
C
0 07
0 12
0 07
0 12
VO = 1.25 V to 2.75 V,
25
C
0.07
0.12
0.07
0.12
SR
Slew rate at unity gain
RL = 100 k
,
C
100 F
Full
0 05
0 05
V/
s
CL = 100 pF
range
0.05
0.05
V
Equivalent input noise
f = 10 Hz
25
C
36
36
nV/
Hz
Vn
q
voltage
f = 1 kHz
25
C
19
19
nV/
Hz
VN(PP)
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz
25
C
0.7
0.7
V
VN(PP)
equivalent input
noise voltage
f = 0.1 Hz to 10 Hz
25
C
1.1
1.1
V
In
Equivalent input noise
current
25
C
0.6
0.6
fA /
Hz
THD + N
Total harmonic
VO = 0.5 V to 2.5 V,
f = 20 kHz
AV = 1
25
C
0.2%
0.2%
THD + N
distortion plus noise
f = 20 kHz,
RL = 50 k
AV = 10
25
C
1%
1%
Gain bandwidth product
f = 50 kHz,
RL = 50 k
,
25
C
0 2
0 2
MHz
Gain-bandwidth product
,
CL = 100 pF
L
,
25
C
0.2
0.2
MHz
BOM
Maximum output-swing
VO(PP) = 2 V,
AV = 1,
25
C
30
30
kHz
BOM
g
bandwidth
O(PP)
,
RL = 50 k
,
V
,
CL = 100 pF
25
C
30
30
kHz
m
Phase margin at unity
gain
RL = 50 k
,
CL = 100 pF
25
C
63
63
Gain margin
L
,
L
25
C
15
15
dB
Full range is 40
C to 125
C for Q level part, 55
C to 125
C for M level part.
Referenced to 2.5 V
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
18
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2254Q, and TLV2254M electrical characteristics at specified free-air temperature, V
DD
= 3 V
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
TLV2254Q,
TLV2254M
TLV2254AQ,
TLV2254AM
UNIT
A
MIN
TYP
MAX
MIN
TYP
MAX
VIO
Input offset voltage
25
C
200
1500
200
850
V
VIO
Input offset voltage
Full range
1750
1000
V
VIO
Temperature coefficient
25
C
0 5
0 5
V/
C
VIO
of input offset voltage
to 125
C
0.5
0.5
V/
C
Input offset voltage
long-
term drift (see Note 4)
VDD
=
1.5 V,
VO = 0,
VIC = 0,
RS = 50
25
C
0.003
0.003
V/mo
IIO
Input offset current
25
C
0.5
60
0.5
60
pA
IIO
Input offset current
125
C
1000
1000
pA
IIB
Input bias current
25
C
1
60
1
60
pA
IIB
Input bias current
125
C
1000
1000
pA
0
0.3
0
0.3
25
C
to
to
to
to
VICR
Common-mode input
RS = 50
|
VIO
|
5 mV
2
2.2
2
2.2
V
VICR
voltage range
RS = 50
,
|
VIO
|
5 mV
0
0
V
Full range
to
to
g
1.7
1.7
IOH = 20
A
25
C
2.98
2.98
VOH
High-level output
IOH = 75
A
25
C
2.9
2.9
V
VOH
g
voltage
IOH = 75
A
Full range
2.8
2.8
V
IOH = 150
A
25
C
2.8
2.8
VIC = 1.5 V,
IOL = 50
A
25
C
10
10
Low level output
VIC = 1 5 V
IOL = 500
A
25
C
100
150
100
150
VOL
Low-level output
voltage
VIC = 1.5 V,
IOL = 500
A
Full range
165
165
mV
voltage
VIC = 1 5 V
IOL
1
m
A
25
C
200
300
200
300
VIC = 1.5 V,
IOL = 1
m
A
Full range
300
300
Large signal differential
V
1 5 V
RL 100 k
25
C
100
225
100
225
AVD
Large-signal differential
voltage amplification
VIC = 1.5 V,
VO = 1 V to 2 V
RL = 100 k
Full range
10
10
V/mV
VD
voltage am lification
VO = 1 V to 2 V
RL = 1 M
25
C
800
800
ri(d)
Differential input
resistance
25
C
1012
1012
ri(c)
Common-mode input
resistance
25
C
1012
1012
ci(c)
Common-mode input
capacitance
f = 10 kHz,
N package
25
C
8
8
pF
zo
Closed-loop output
impedance
f = 25 kHz,
AV = 10
25
C
220
220
CMRR
Common-mode
VIC = 0 to 1.7 V, VO = 1.5 V,
25
C
65
75
65
77
dB
CMRR
rejection ratio
IC
RS = 50
O
Full range
60
60
dB
kSVR
Supply voltage
rejection ratio
VDD = 2.7 V to 8 V,
25
C
80
95
80
100
dB
kSVR
rejection ratio
(
VDD /
VIO)
DD
VIC = VDD /2, No
load
Full range
80
80
dB
Full range is 40
C to 125
C for Q level part, 55
C to 125
C for M level part.
Referenced to 1.5 V
NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150
C extrapolated
to TA = 25
C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
19
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2254Q, and TLV2254M electrical characteristics at specified free-air temperature, V
DD
= 3 V
(unless otherwise noted) (continued)
PARAMETER
TEST CONDITIONS
TA
TLV2254Q,
TLV2254M
TLV2254AQ,
TLV2254AM
UNIT
A
MIN
TYP
MAX
MIN
TYP
MAX
IDD
Supply current
VO = 1 5 V
No load
25
C
135
250
135
250
A
IDD
y
(four amplifiers)
VO = 1.5 V,
No load
Full range
300
300
A
Full range is 40
C to 125
C for Q level part, 55
C to 125
C for M level part.
TLV2254Q, and TLV2254M operating characteristics at specified free-air temperature, V
DD
= 3 V
PARAMETER
TEST CONDITIONS
TA
TLV2254Q,
TLV2254M
TLV2254AQ,
TLV2254AM
UNIT
A
MIN
TYP
MAX
MIN
TYP
MAX
SR
Slew rate at unity gain
VO = 0.5 V to 1.7 V,
RL = 100 k
25
C
0.07
0.1
0.07
0.1
V/
s
SR
Slew rate at unity gain
RL = 100 k
,
C
100 F
Full range
0 05
0 05
V/
s
CL = 100 pF
Full range
0.05
0.05
V
Equivalent input noise voltage
f = 10 Hz
25
C
35
35
nV/
Hz
Vn
Equivalent input noise voltage
f = 1 kHz
25
C
19
19
nV/
Hz
VN(PP)
Peak-to-peak equivalent input
f = 0.1 Hz to 1 Hz
25
C
0.6
0.6
V
VN(PP)
q
noise voltage
f = 0.1 Hz to 10 Hz
25
C
1.1
1.1
V
In
Equivalent input noise current
25
C
0.6
0.6
fA /
Hz
Gain bandwidth product
f = 1 kHz,
RL 50 k
25
C
0 187
0 187
MHz
Gain-bandwidth product
RL = 50 k
,
CL = 100 pF
25
C
0.187
0.187
MHz
BOM
Maximum output-swing
VO(PP) = 1 V,
AV = 1,
25
C
60
60
kHz
BOM
g
bandwidth
V
,
RL = 50 k
,
CL = 100 pF
25
C
60
60
kHz
m
Phase margin at unity gain
RL = 50 k
,
25
C
63
63
Gain margin
L
,
CL = 100 pF
25
C
15
15
dB
Full range is 40
C to 125
C for Q level part, 55
C to 125
C for M level part.
Referenced to 1.5 V
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
20
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2254Q, and TLV2254M electrical characteristics at specified free-air temperature, V
DD
= 5 V
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
TLV2254Q,
TLV2254M
TLV2254AQ,
TLV2254AM
UNIT
A
MIN
TYP
MAX
MIN
TYP
MAX
VIO
Input offset voltage
25
C
200
1500
200
850
V
VIO
Input offset voltage
Full range
1750
1000
V
VIO
Temperature coefficient
25
C
0 5
0 5
V/
C
VIO
of input offset voltage
to 125
C
0.5
0.5
V/
C
Input offset voltage
long-term drift
(see Note 4)
VDD
=
2.5 V,
VO = 0,
VIC = 0,
RS = 50
25
C
0.003
0.003
V/mo
IIO
Input offset current
25
C
0.5
60
0.5
60
pA
IIO
Input offset current
125
C
1000
1000
pA
IIB
Input bias current
25
C
1
60
1
60
pA
IIB
Input bias current
125
C
1000
1000
pA
0
0.3
0
0.3
25
C
to
to
to
to
VICR
Common-mode input
|
VIO
|
5 mV
RS = 50
4
4.2
4
4.2
V
VICR
voltage range
|
VIO
|
5 mV,
RS = 50
0
0
V
Full range
to
to
g
3.5
3.5
IOH = 20
A
25
C
4.98
4.98
VOH
High-level output
IOH = 75
A
25
C
4.9
4.94
4.9
4.94
V
VOH
g
voltage
IOH = 75
A
Full range
4.8
4.8
V
IOH = 150
A
25
C
4.8
4.88
4.8
4.88
VIC = 2.5 V,
IOL = 50
A
25
C
0.01
0.01
Low level output
VIC = 2 5 V
IOL = 500
A
25
C
0.09
0.15
0.09
0.15
VOL
Low-level output
voltage
VIC = 2.5 V,
IOL = 500
A
Full range
0.15
0.15
V
voltage
VIC = 2 5 V
IOL
1
m
A
25
C
0.2
0.3
0.2
0.3
VIC = 2.5 V,
IOL = 1
m
A
Full range
0.3
0.3
Large signal differential
V
2 5 V
RL 100 k
25
C
100
350
100
350
AVD
Large-signal differential
voltage amplification
VIC = 2.5 V,
VO = 1 V to 4 V
RL = 100 k
Full range
10
10
V/mV
VD
voltage am lification
VO = 1 V to 4 V
RL = 1 M
25
C
1700
1700
ri(d)
Differential input
resistance
25
C
1012
1012
ri(c)
Common-mode input
resistance
25
C
1012
1012
ci(c)
Common-mode input
capacitance
f = 10 kHz,
N package
25
C
8
8
pF
zo
Closed-loop output
impedance
f = 25 kHz,
AV = 10
25
C
200
200
CMRR
Common-mode
VIC = 0 to 2.7 V, VO = 2.5 V,
25
C
70
83
70
83
dB
CMRR
rejection ratio
IC
RS = 50
O
Full range
70
70
dB
kSVR
Supply voltage
rejection ratio
VDD = 4.4 V to 8 V,
25
C
80
95
80
95
dB
kSVR
rejection ratio
(
VDD /
VIO)
DD
,
VIC = VDD /2, No
load
Full range
80
80
dB
Full range is 40
C to 125
C for Q level part, 55
C to 125
C for M level part.
Referenced to 2.5 V
NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150
C extrapolated
to TA = 25
C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
21
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TLV2254Q, and TLV2254M electrical characteristics at specified free-air temperature, V
DD
= 5 V
(unless otherwise noted) (continued)
PARAMETER
TEST CONDITIONS
TA
TLV2254Q,
TLV2254M
TLV2254AQ,
TLV2254AM
UNIT
A
MIN
TYP
MAX
MIN
TYP
MAX
IDD
Supply current
VO = 2 5 V
No load
25
C
140
250
140
250
A
IDD
y
(four amplifiers)
VO = 2.5 V,
No load
Full range
300
300
A
Full range is 40
C to 125
C for Q level part, 55
C to 125
C for M level part.
TLV2254Q, and TLV2254M operating characteristics at specified free-air temperature, V
DD
= 5 V
PARAMETER
TEST CONDITIONS
TA
TLV2254Q,
TLV2254M
TLV2254AQ,
TLV2254AM
UNIT
A
MIN
TYP
MAX
MIN
TYP
MAX
Slew rate at unity
VO = 0 5 V to 3 5 V
RL 100 k
25
C
0.07
0.12
0.07
0.12
SR
Slew rate at unity
gain
VO = 0.5 V to 3.5 V,
CL = 100 pF
RL = 100 k
,
Full
0 05
0 05
V/
s
gain
CL = 100 F
range
0.05
0.05
V
Equivalent input
f = 10 Hz
25
C
36
36
nV/
Hz
Vn
q
noise voltage
f = 1 kHz
25
C
19
19
nV/
Hz
VN(PP)
Peak-to-peak
equivalent input
f = 0.1 Hz to 1 Hz
25
C
0.7
0.7
V
VN(PP)
equivalent input
noise voltage
f = 0.1 Hz to 10 Hz
25
C
1.1
1.1
V
In
Equivalent input
noise current
25
C
0.6
0.6
fA /
Hz
THD + N
Total harmonic
distortion plus
VO = 0.5 V to 2.5 V,
f = 20 kHz
AV = 1
25
C
0.2%
0.2%
THD + N
distortion plus
noise
f = 20 kHz,
RL = 50 k
AV = 10
25
C
1%
1%
Gain-bandwidth
f = 50 kHz,
RL = 50 k
,
25
C
0 2
0 2
MHz
product
,
CL = 100 pF
L
,
25
C
0.2
0.2
MHz
BOM
Maximum output-
VO(PP) = 2 V,
AV = 1,
25
C
30
30
kHz
BOM
swing bandwidth
O(PP)
,
RL = 50 k
,
V
,
CL = 100 pF
25
C
30
30
kHz
m
Phase margin at
unity gain
RL = 50 k
,
CL = 100 pF
25
C
63
63
Gain margin
L
,
L
25
C
15
15
dB
Full range is 40
C to 125
C for Q level part, 55
C to 125
C for M level part.
Referenced to 2.5 V
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
22
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VIO
Input offset voltage
Distribution
vs Common-mode voltage
2 5
6, 7
VIO
Input offset voltage temperature coefficient
Distribution
8 11
IIB /IIO
Input bias and input offset currents
vs Free-air temperature
12
VI
Input voltage
vs Supply voltage
vs Free-air temperature
13
14
VOH
High-level output voltage
vs High-level output current
15, 18
VOL
Low-level output voltage
vs Low-level output current
16, 17, 19
VO(PP)
Maximum peak-to-peak output voltage
vs Frequency
20
IOS
Short-circuit output current
vs Supply voltage
vs Free-air temperature
21
22
VID
Differential input voltage
vs Output voltage
23, 24
AVD
Differential voltage amplification
vs Load resistance
25
AVD
Large-signal differential voltage amplification
vs Frequency
vs Free-air temperature
26, 27
28, 29
zo
Output impedance
vs Frequency
30, 31
CMRR
Common-mode rejection ratio
vs Frequency
vs Free-air temperature
32
33
kSVR
Supply-voltage rejection ratio
vs Frequency
vs Free-air temperature
34, 35
36
IDD
Supply current
vs Supply voltage
37, 38
SR
Slew rate
vs Load capacitance
vs Free-air temperature
39
40
VO
Inverting large-signal pulse response
41, 42
VO
Voltage-follower large-signal pulse response
43, 44
VO
Inverting small-signal pulse response
45, 46
VO
Voltage-follower small-signal pulse response
47, 48
Vn
Equivalent input noise voltage
vs Frequency
49, 50
Input noise voltage
Over a 10-second period
51
Integrated noise voltage
vs Frequency
52
THD + N
Total harmonic distortion plus noise
vs Frequency
53
Gain-bandwidth product
vs Supply voltage
vs Free-air temperature
54
55
m
Phase margin
vs Frequency
vs Load capacitance
26, 27
56
Gain margin
vs Load capacitance
57
B1
Unity-gain bandwidth
vs Load capacitance
58
Overestimation of phase margin
vs Load capacitance
59
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
23
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 2
Precentage of
Amplifiers
%
DISTRIBUTION OF TLV2252
INPUT OFFSET VOLTAGE
VIO Input Offset Voltage mV
10
5
0
20
15
1.6
0.8
0
0.8
1.6
1020 Amplifiers From 1 Wafer Lot
VDD =
1.5 V
TA = 25
C
Figure 3
Precentage of
Amplifiers
%
DISTRIBUTION OF TLV2252
INPUT OFFSET VOLTAGE
VIO Input Offset Voltage mV
10
5
0
20
15
1.6
0.8
0
0.8
1.6
1020 Amplifiers From 1 Wafer Lot
VDD =
2.5 V
TA = 25
C
Figure 4
Percentage of
Amplifiers
%
DISTRIBUTION OF TLV2254
INPUT OFFSET VOLTAGE
VIO Input Offset Voltage mV
15
10
5
0
20
35
1.6
0.8
0
0.8
1.6
25
30
682 Amplifiers From 1 Wafer Lot
VDD
=
1.5 V
TA = 25
C
Figure 5
Percentage of
Amplifiers
%
DISTRIBUTION OF TLV2254
INPUT OFFSET VOLTAGE
VIO Input Offset Voltage mV
20
10
5
0
25
35
1.6
0.8
0
0.8
1.6
682 Amplifiers From 1 Wafer Lot
VDD
=
2.5 V
TA = 25
C
15
30
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
24
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 6
Input Offset V
oltage
mV
INPUT OFFSET VOLTAGE
vs
COMMON-MODE INPUT VOLTAGE
V
IO
VIC Common-Mode Input Voltage V
1
0.8
0.6
0.4
0.2
0
0.2
0.4
0.6
0.8
1
1
0
1
2
VDD = 3 V
RS = 50
TA = 25
C
3
Figure 7
Input Offset V
oltage
mV
INPUT OFFSET VOLTAGE
vs
COMMON-MODE INPUT VOLTAGE
V
IO
VIC Common-Mode Input Voltage V
1
0.8
0.6
0.4
0.2
0
0.2
0.4
0.6
0.8
1
1
0
1
2
3
4
5
VDD = 5 V
RS = 50
TA = 25
C
Figure 8
DISTRIBUTION OF TLV2252 INPUT OFFSET
VOLTAGE TEMPERATURE COEFFICIENT
Percentage of
Amplifiers
%
VIO Temperature Coefficient
V /
C
15
10
5
0
20
25
2
1
0
1
2
62 Amplifiers From 1 Wafer Lot
VDD
=
1.5 V
P Package
TA = 25
C to 85
C
Figure 9
DISTRIBUTION OF TLV2252 INPUT OFFSET
VOLTAGE TEMPERATURE COEFFICIENT
Percentage of
Amplifiers
%
VIO Temperature Coefficient
V /
C
15
10
5
0
20
25
2
1
0
1
2
62 Amplifiers From 1 Wafer Lot
VDD
=
2.5 V
P Package
TA = 25
C to 85
C
For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
25
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 10
DISTRIBUTION OF TLV2254 INPUT OFFSET
VOLTAGE TEMPERATURE COEFFICIENT
Percentage of
Amplifiers
%
VIO Temperature Coefficient
of Input Offset Voltage
V /
C
10
5
0
20
15
25
2
1
0
1
2
62 Amplifiers From 1 Wafer Lot
VDD
=
1.5 V
P Package
TA = 25
C to 85
C
Figure 11
DISTRIBUTION OF TLV2254 INPUT OFFSET
VOLTAGE TEMPERATURE COEFFICIENT
Percentage of
Amplifiers
%
VIO Temperature Coefficient
of Input Offset Voltage
V /
C
10
5
0
20
15
25
2
1
0
1
2
62 Amplifiers From 1 Wafer Lot
VDD
=
2.5 V
P Package
TA = 25
C to 85
C
Figure 12
IIB and IIO
Input Bias and Input Offset Currents
pA
INPUT BIAS AND INPUT OFFSET CURRENTS
vs
FREE-AIR TEMPERATURE
I IB
I IO
TA Free-Air Temperature
C
20
15
25
45
65
25
30
35
85
IIB
IIO
10
5
0
105
125
VDD
=
2.5 V
VIC = 0
VO = 0
RS = 50
Figure 13
0
2
1
1.5
2
2.5
Input V
oltage
V
1
0.5
1.5
INPUT VOLTAGE
vs
SUPPLY VOLTAGE
2.5
3
3.5
4
0.5
1
1.5
2
2.5
RS = 50
TA = 25
C
| VIO |
5 mV
V
I
| VDD
| Supply Voltage V
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
26
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 14
Input V
oltage
V
INPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
V
I
TA Free-Air Temperature
C
2
1
0
3
4
5
1
55 35 15
5
25
45
65
85
| VIO |
5 mV
VDD = 5 V
105
125
Figure 15
High-Level Output V
oltage
V
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
V
OH
| IOH | High-Level Output Current
A
2
1.5
1
0
0
200
400
2.5
3
600
800
VDD = 3 V
TA = 40
C
TA = 25
C
TA = 85
C
0.5
TA = 125
C
Figure 16
0.6
0.4
0.2
0
0
1
2
3
Low-Level Output V
oltage
V
0.8
1
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
1.2
4
5
V
OL
IOL Low-Level Output Current mA
VDD = 3 V
TA = 25
C
VIC = 0
VIC = 0.75 V
VIC = 1.5 V
Figure 17
Low-Level Output V
oltage
V
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
V
OL
IOL Low-Level Output Current mA
0.4
0.2
1.2
0
0
1
2
3
0.8
0.6
1
1.4
4
5
TA = 85
C
TA = 40
C
TA = 25
C
TA = 125
C
VDD = 3 V
VIC = 1.5 V
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
27
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 18
High-Level Output V
oltage
V
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
V
OH
| IOH | High-Level Output Current
A
3
2
1
0
0
200
400
4
5
600
800
VDD = 5 V
TA = 40
C
TA = 25
C
TA = 125
C
TA = 85
C
Figure 19
Low-Level Output V
oltage
V
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
V
OL
IOL Low-Level Output Current mA
0.6
0.4
0.2
0
0
1
2
3
1
1.2
1.4
4
5
6
0.8
VDD = 5 V
VIC = 2.5 V
TA = 40
C
TA = 85
C
TA = 25
C
TA = 125
C
Figure 20
Maximum Peak-to-Peak Output V
oltage
V
f Frequency Hz
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE
vs
FREQUENCY
V
O(PP)
4
2
1
5
3
0
10 2
10 3
10 4
10 5
RI = 50 k
TA = 25
C
VDD = 5 V
VDD = 3 V
Figure 21
Short-Circuit Output Current
mA
SHORT-CIRCUIT OUTPUT CURRENT
vs
SUPPLY VOLTAGE
I OS
VDD Supply Voltage V
5
3
1
2
3
4
5
7
8
10
6
7
8
9
6
4
2
0
1
VID = 100 mV
VID = 100 mV
VO = VDD/2
TA = 25
C
VIC = VDD/2
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
28
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 22
Short-Circuit Output Current
mA
SHORT-CIRCUIT OUTPUT CURRENT
vs
FREE-AIR TEMPERATURE
I OS
TA Free-Air Temperature
C
11
10
9
8
7
6
5
4
3
2
1
0
1
50
25
0
25
50
75
100
VID = 100 mV
VID = 100 mV
VO = 2.5 V
VDD =
5 V
75
125
Figure 23
0
800
0
0.5
1
1.5
Differential Input V
oltage
400
200
600
DIFFERENTIAL INPUT VOLTAGE
vs
OUTPUT VOLTAGE
1000
2
2.5
3
200
400
600
800
1000
VDD = 3 V
RI = 50 k
VIC = 1.5 V
TA = 25
C
V
ID
V
VO Output Voltage V
Figure 24
0
800
0
1
3
Differential Input V
oltage
400
200
600
DIFFERENTIAL INPUT VOLTAGE
vs
OUTPUT VOLTAGE
1000
2
4
5
200
400
600
800
1000
V
ID
V
VO Output Voltage V
VDD = 5 V
VIC = 2.5 V
RL = 50 k
TA = 25
C
Figure 25
DIFFERENTIAL VOLTAGE AMPLIFICATION
vs
LOAD RESISTANCE
RL Load Resistance k
Differential V
oltage
Amplification
V/mV
A
VD
1
101
10 2
10 3
10 2
101
1
10 3
10 4
VO(PP) = 2 V
TA = 25
C
VDD = 5 V
VDD = 3 V
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
29
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
om
Phase Margin
m
f Frequency Hz
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE MARGIN
vs
FREQUENCY
A
VD
Large-Signal Differential
A
VD
V
oltage Amplification
dB
20
80
60
40
0
20
40
10 3
10 4
10 5
10 6
10 7
180
135
90
45
0
45
90
Gain
VDD = 5 V
RL = 50 k
CL= 100 pF
TA = 25
C
Phase Margin
Figure 26
om
Phase Margin
m
f Frequency Hz
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE MARGIN
vs
FREQUENCY
A
VD
Large-Signal Differential
A
VD
V
oltage Amplification
dB
20
80
60
40
0
20
40
10 3
10 4
10 5
10 6
10 7
180
135
90
45
0
45
90
Gain
VDD = 3 V
RL= 50 k
CL= 100 pF
TA = 25
C
Phase Margin
Figure 27
For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
30
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 28
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION
vs
FREE-AIR TEMPERATURE
TA Free-Air Temperature
C
Large-Signal Differential V
oltage
A
VD
Amplification
V/mV
50
25
0
25
50
75
100
RL = 50 k
RL = 1 M
10 4
10 3
10 2
101
VDD = 3 V
VIC = 1.5 V
VO = 0.5 V to 2.5 V
75
125
Figure 29
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION
vs
FREE-AIR TEMPERATURE
TA Free-Air Temperature
C
Large-Signal Differential V
oltage
A
VD
Amplification
V/mV
50
25
0
25
50
75
100
125
VDD = 5 V
VIC = 2.5 V
VO = 1 V to 4 V
RL = 50 k
RL = 1 M
10 4
10 3
10 2
101
75
Figure 30
Output Impedance
f Frequency Hz
OUTPUT IMPEDANCE
vs
FREQUENCY
z
o
10
1
0.1
1000
100
10 2
10 3
10 4
10 5
10 6
AV = 100
AV = 10
AV = 1
VDD = 3 V
TA = 25
C
Figure 31
Output Impedance
f Frequency Hz
OUTPUT IMPEDANCE
vs
FREQUENCY
z
o
10
1
0.1
1000
100
10 2
10 3
10 4
10 5
10 6
AV = 100
AV = 10
AV = 1
VDD = 5 V
TA = 25
C
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
31
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 32
CMRR
Common-Mode Rejection Ratio
dB
f Frequency Hz
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
80
40
20
0
100
60
10 1
10 2
10 3
10 4
10 5
10 6
VDD = 5 V
VIC = 2.5 V
VDD = 3 V
VIC = 1.5 V
TA = 25
C
Figure 33
CMMR
Common-Mode Rejection Ratio
dB
COMMON-MODE REJECTION RATIO
vs
FREE-AIR TEMPERATURE
TA Free-Air Temperature
C
86
82
80
92
84
90
88
94
VDD = 5 V
VDD = 3 V
50
25
0
25
50
75
100
75
125
Figure 34
Supply-V
oltage Rejection Ratio
dB
f Frequency Hz
SUPPLY-VOLTAGE REJECTION RATIO
vs
FREQUENCY
k
SVR
60
40
20
100
80
0
20
kSVR
kSVR +
10 1
10 2
10 3
10 4
10 5
10 6
VDD = 3 V
TA = 25
C
Figure 35
Supply-V
oltage Rejection Ratio
dB
f Frequency Hz
SUPPLY-VOLTAGE REJECTION RATIO
vs
FREQUENCY
k
SVR
100
80
60
40
20
0
20
101
10 2
10 3
10 4
10 5
10 6
VDD = 5 V
TA = 25
C
kSVR
kSVR +
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
32
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 36
Supply-V
oltage Rejection Ratio
dB
SUPPLY-VOLTAGE REJECTION RATIO
vs
FREE-AIR TEMPERATURE
k
SVR
TA Free-Air Temperature
C
100
95
90
105
110
50
25
0
25
50
75
100
VDD = 2.7 V to 8 V
VIC = VO = VDD / 2
125
75
Figure 37
Supply Current
A
I DD
60
40
20
0
0
1
2
3
4
5
80
100
120
6
7
8
VDD Supply Voltage V
VO = 0
No Load
TA = 25
C
TA = 85
C
TA = 40
C
TLV2252
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
Figure 38
Supply Current
A
I DD
120
80
40
0
0
1
2
3
4
5
160
200
240
6
7
8
| VDD
| Supply Voltage V
VO = 0
No Load
TA = 25
C
TA = 85
C
TA = 40
C
TLV2254
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
Figure 39
SR
Slew Rate
SLEW RATE
vs
LOAD CAPACITANCE
CL Load Capacitance pF
s
V/
0.16
0.08
0.04
0
0.2
0.12
101
10 2
10 3
10 4
VDD = 5 V
AV = 1
TA = 25
C
SR
0.18
0.14
0.1
0.06
0.02
SR +
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
33
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 40
SR
Slew Rate
SLEW RATE
vs
FREE-AIR TEMPERATURE
s
V/
TA Free-Air Temperature
C
0.08
0.04
0
0.12
0.16
0.2
50
25
0
25
50
75
100
SR
SR +
VDD = 5 V
RL = 50 k
CL = 100 pF
A V = 1
75
125
Figure 41
Output V
oltage
V
INVERTING LARGE-SIGNAL PULSE
RESPONSE
V
O
t Time
s
1.5
1
0.5
0
0
10
20
30
40
50
60
2
2.5
3
70
80
90
100
A V = 1
TA = 25
C
VDD = 3 V
RL = 50 k
CL = 100 pF
Figure 42
INVERTING LARGE-SIGNAL PULSE
RESPONSE
t Time
s
Output V
oltage
V
V
O
2
1
0
0
10
20
30
40
50
60
3
4
5
70
80
90
100
VDD = 5 V
RL = 50 k
CL = 100 pF
AV = 1
TA = 25
C
Figure 43
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE
Output V
oltage
V
V
O
t Time
s
1.5
1
0.5
0
0
10
20
30
40
50
60
2
2.5
3
70
80
90
100
A V = 1
TA = 25
C
VDD = 3 V
RL = 50 k
CL = 100 pF
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
34
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 44
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE
Output V
oltage
V
V
O
t Time
s
2
1
0
0
10
20
30
40
50
60
3
4
5
70
80
90
100
VDD = 5 V
RL = 50 k
CL = 100 pF
AV = 1
TA = 25
C
Figure 45
INVERTING SMALL-SIGNAL
PULSE RESPONSE
Output V
oltage
V
V
O
t Time
s
0.7
0.65
0.9
0.6
0
10
20
30
0.8
0.75
0.85
0.95
40
50
VDD = 3 V
RL = 50 k
CL = 100 pF
AV = 1
TA = 25
C
Figure 46
VO
Output V
oltage
V
INVERTING SMALL-SIGNAL
PULSE RESPONSE
V
O
t Time
s
2.5
2.45
2.4
0
10
20
30
2.55
2.6
2.65
40
50
VDD = 5 V
RL = 50 k
CL = 100 pF
AV = 1
TA = 25
C
Figure 47
VOLTAGE-FOLLOWER SMALL-SIGNAL
PULSE RESPONSE
VO
Output V
oltage
V
V
O
t Time
s
0.8
0.75
0.6
0
10
20
30
0.85
0.9
0.95
40
50
0.7
0.65
VDD = 3 V
RL = 50 k
CL = 100 pF
AV = 1
TA = 25
C
For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
35
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 48
VOLTAGE-FOLLOWER SMALL-SIGNAL
PULSE RESPONSE
VO
Output V
oltage
V
V
O
t Time
s
2.5
2.45
2.4
0
10
20
30
2.55
2.6
2.65
40
50
VDD = 5 V
RL = 50 k
CL = 100 pF
AV = 1
TA = 25
C
Figure 49
Equivalent Input Noise V
oltage
f Frequency Hz
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
V
n
nV/
Hz
40
30
20
0
60
50
10
10 1
10 2
10 3
10 4
VDD = 3 V
RS = 20
TA = 25
C
Figure 50
Equivalent Input Noise V
oltage
f Frequency Hz
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
V
n
nV/
Hz
40
20
10
0
60
30
50
101
10 2
10 3
10 4
VDD = 5 V
RS = 20
TA = 25
C
Figure 51
Noise V
oltage
nV
t Time s
INPUT NOISE VOLTAGE OVER
A 10-SECOND PERIOD
0
2
4
6
0
750
1000
8
10
500
250
500
750
1000
250
VDD = 5 V
f = 0.1 Hz to 10 Hz
TA = 25
C
For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
36
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 52
Integrated Noise V
oltage
f Frequency Hz
INTEGRATED NOISE VOLTAGE
vs
FREQUENCY
V
0.1
1
10
100
1
101
10 2
10 3
10 4
10 5
Calculated Using Ideal Pass-Band Filter
Low Frequency = 1 Hz
TA = 25
C
Figure 53
THD + N
T
otal Harmonic Distortion Plus Noise
%
f Frequency Hz
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
FREQUENCY
0.01
1
0.001
101
10 2
10 3
10 4
10 5
AV = 10
AV = 1
VDD = 5 V
RL = 50 k
TA = 25
C
0.1
AV = 100
Figure 54
Gain-Bandwidth Product
kHz
GAIN-BANDWIDTH PRODUCT
vs
SUPPLY VOLTAGE
VDD Supply Voltage V
200
190
180
170
0
2
3
5
210
220
7
8
1
4
6
Figure 55
Gain-Bandwidth Product
kHz
GAIN-BANDWIDTH PRODUCT
vs
FREE-AIR TEMPERATURE
TA Free-Air Temperature
C
220
140
100
260
300
50 25
0
25
50
100
75
180
VDD = 5 V
f = 10 kHz
RL = 50 kHz
CL = 100 pF
125
75
For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
37
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 56
om
Phase Margin
PHASE MARGIN
vs
LOAD CAPACITANCE
CL Load Capacitance pF
m
101
10 2
10 3
10 4
75
60
45
30
15
0
Rnull = 200
Rnull = 500
Rnull = 50
Rnull = 0
TA = 25
C
Rnull = 100
Rnull = 10
50 k
50 k
VDD
VDD +
Rnull
CL
VI
+
Figure 57
Gain Margin
dB
GAIN MARGIN
vs
LOAD CAPACITANCE
CL Load Capacitance pF
20
10
5
0
15
101
10 2
10 3
10 5
Rnull = 100
TA = 25
C
Rnull = 50
10 4
Rnull = 500
Rnull = 200
Rnull = 0
Rnull = 10
Figure 58
Unity-Gain Bandwidth
kHz
UNITY-GAIN BANDWIDTH
vs
LOAD CAPACITANCE
CL Load Capacitance pF
B
1
150
25
100
0
200
125
175
50
75
101
10 2
10 3
10 4
10 5
TA = 25
C
See application information
Figure 59
Overestimation of Phase Margin
OVERESTIMATION OF PHASE MARGIN
vs
LOAD CAPACITANCE
CL Load Capacitance pF
15
10
5
0
20
25
101
10 2
10 3
10 4
10 5
TA = 25
C
Rnull = 100
Rnull = 50
Rnull = 10
Rnull = 500
Rnull = 200
Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
38
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
driving large capacitive loads
The TLV2252 is designed to drive larger capacitive loads than most CMOS operational amplifiers. Figure 56
and Figure 57 illustrate its ability to drive loads up to 1000 pF while maintaining good gain and phase margins
(R
null
= 0).
A smaller series resistor (R
null
) at the output of the device (see Figure 60) improves the gain and phase margins
when driving large capacitive loads. Figure 55 and Figure 56 show the effects of adding series resistances of
10
, 50
, 100
, 200
, and 500
. The addition of this series resistor has two effects: the first adds a zero
to the transfer function and the second reduces the frequency of the pole associated with the output load in the
transfer function.
The zero introduced to the transfer function is equal to the series resistance times the load capacitance. To
calculate the improvement in phase margin, equation 1 can be used.
m1
+
tan
1
2
UGB
W
R
null
C
L
m1
+
improvement in phase margin
UGBW
+
unity-gain bandwidth frequency
R
null
+
output series resistance
C
L
+
load capacitance
(1)
Where :
The unity-gain bandwidth (UGBW) frequency decreases as the capacitive load increases (see Figure 58). To
use equation 1, UGBW must be approximated from Figure 58.
Using equation 1 alone overestimates the improvement in phase margin as illustrated in Figure 59. The
overestimation is caused by the decrease in the frequency of the pole associated with the load, providing
additional phase shift and reducing the overall improvement in phase margin.
Using Figure 60, with equation 1 enables the designer to choose the appropriate output series resistance to
optimize the design of circuits driving large capacitance loads.
50 k
50 k
VDD / GND
VDD +
Rnull
CL
VI
+
Figure 60. Series-Resistance Circuit
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
39
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
macromodel information
Macromodel information provided was derived using Microsim Parts
, the model generation software used
with Microsim PSpice
. The Boyle macromodel (see Note 5) and subcircuit in Figure 61 are generated using
the TLV2252 typical electrical and operating characteristics at T
A
= 25
C. Using this information, output
simulations of the following key parameters can be generated to a tolerance of 20% (in most cases):
D
Maximum positive output voltage swing
D
Maximum negative output voltage swing
D
Slew rate
D
Quiescent power dissipation
D
Input bias current
D
Open-loop voltage amplification
D
Unity-gain frequency
D
Common-mode rejection ratio
D
Phase margin
D
DC output resistance
D
AC output resistance
D
Short-circuit output current limit
NOTE 5: G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, "Macromodeling of Integrated Circuit Operational Amplifiers," IEEE Journal
of Solid-State Circuits, SC-9, 353 (1974).
OUT
+
+
+
+
+
+
+
+
+
.SUBCKT TLV225x 1 2 3 4 5
C1
11
12
6.369E12
C2
6
7
25.00E12
DC
5
53
DX
DE
54
5
DX
DLP
90
91
DX
DLN
92
90
DX
DP
4
3
DX
EGND
99
0
POLY (2) (3,0) (4,0) 0 .5 .5
FB
7
99
POLY (5) VB VC VE VLP
+ VLN 0 57.62E6 60E6 60E6 60E6 60E6
GA
6
0
11
12 26.86E6
GCM 0
6
10
99
2.686E9
ISS
3
10
DC 3.1E6
HLIM
90
0
VLIM 1K
J1
11
2
10 JX
J2
12
1
10 JX
R2
6
9
100.0E3
RD1
60
11
37.23E3
RD2
60
12
37.23E3
R01
8
5
84
R02
7
99
84
RP
3
4
71.43E3
RSS
10
99
64.52E6
VAD
60
4
.5
VB
9
0
DC 0
VC 3
53
DC
.605
VE
54
4
DC .605
VLIM
7
8
DC 0
VLP
91
0
DC 0.235
VLN
0
92
DC 7.5
.MODEL DX D (IS=800.0E18)
.MODEL JX PJF (IS=500.0E15 BETA=139E6
+ VTO=.05)
.ENDS
VCC +
RP
IN
2
IN +
1
VCC
VAD
RD1
11
J1
J2
10
RSS
ISS
3
12
RD2
60
VE
54
DE
DP
VC
DC
4
C1
53
R2
6
9
EGND
VB
FB
C2
GCM
GA
VLIM
8
5
RO1
RO2
HLIM
90
DLP
91
DLN
92
VLN
VLP
99
7
Figure 61. Boyle Macromodel and Subcircuit
PSpice and Parts are trademarks of MicroSim Corporation.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
40
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
MECHANICAL INFORMATION
D (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
4040047 / D 10/96
0.228 (5,80)
0.244 (6,20)
0.069 (1,75) MAX
0.010 (0,25)
0.004 (0,10)
1
14
0.014 (0,35)
0.020 (0,51)
A
0.157 (4,00)
0.150 (3,81)
7
8
0.044 (1,12)
0.016 (0,40)
Seating Plane
0.010 (0,25)
PINS **
0.008 (0,20) NOM
A MIN
A MAX
DIM
Gage Plane
0.189
(4,80)
(5,00)
0.197
8
(8,55)
(8,75)
0.337
14
0.344
(9,80)
16
0.394
(10,00)
0.386
0.004 (0,10)
M
0.010 (0,25)
0.050 (1,27)
0
8
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
D. Falls within JEDEC MS-012
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
41
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
MECHANICAL INFORMATION
FK (S-CQCC-N**)
LEADLESS CERAMIC CHIP CARRIER
4040140 / D 10/96
28 TERMINAL SHOWN
B
0.358
(9,09)
MAX
(11,63)
0.560
(14,22)
0.560
0.458
0.858
(21,8)
1.063
(27,0)
(14,22)
A
NO. OF
MIN
MAX
0.358
0.660
0.761
0.458
0.342
(8,69)
MIN
(11,23)
(16,26)
0.640
0.739
0.442
(9,09)
(11,63)
(16,76)
0.962
1.165
(23,83)
0.938
(28,99)
1.141
(24,43)
(29,59)
(19,32)
(18,78)
**
20
28
52
44
68
84
0.020 (0,51)
TERMINALS
0.080 (2,03)
0.064 (1,63)
(7,80)
0.307
(10,31)
0.406
(12,58)
0.495
(12,58)
0.495
(21,6)
0.850
(26,6)
1.047
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.035 (0,89)
0.010 (0,25)
12
13
14
15
16
18
17
11
10
8
9
7
5
4
3
2
0.020 (0,51)
0.010 (0,25)
6
1
28
26
27
19
21
B SQ
A SQ
22
23
24
25
20
0.055 (1,40)
0.045 (1,14)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a metal lid.
D. The terminals are gold plated.
E. Falls within JEDEC MS-004
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
42
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
MECHANICAL INFORMATION
J (R-GDIP-T**)
CERAMIC DUAL-IN-LINE PACKAGE
4040083 / B 04/95
14 PIN SHOWN
22
0.410
(10,41)
0.390
(28,00)
1.100
(9,91)
0.388
(9,65)
20
18
16
14
PINS **
0.310
(7,87)
0.290
0.755
(19,18)
(19,94)
0.785
(7,37)
0.310
(7,87)
(7,37)
0.290
(23,10)
0.910
0.300
(7,62)
(6,22)
0.245
A
0.300
(7,62)
(6,22)
0.245
0.290
(7,87)
0.310
0.785
(19,94)
(19,18)
0.755
(7,37)
A MIN
A MAX
B MAX
B MIN
0.245
(6,22)
(7,11)
0.280
C MIN
C MAX
DIM
0.245
(6,22)
(7,62)
0.300
0.975
(24,77)
(23,62)
0.930
0.290
(7,37)
(7,87)
0.310
Seating Plane
0.014 (0,36)
0.008 (0,20)
C
8
7
0.020 (0,51) MIN
B
0.070 (1,78)
0.100 (2,54)
0.065 (1,65)
0.045 (1,14)
14
1
0.015 (0,38)
0.023 (0,58)
0.200 (5,08) MAX
0.130 (3,30) MIN
0.100 (2,54)
0
15
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification only on press ceramic glass frit seal only.
E. Falls within MIL STD 1835 GDIP1-T14, GDIP1-T16, GDIP1-T18, GDIP1-T20, and GDIP1-T22.
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
43
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
MECHANICAL INFORMATION
JG (R-GDIP-T8)
CERAMIC DUAL-IN-LINE PACKAGE
0.310 (7,87)
0.290 (7,37)
0.014 (0,36)
0.008 (0,20)
Seating Plane
4040107/C 08/96
5
4
0.065 (1,65)
0.045 (1,14)
8
1
0.020 (0,51) MIN
0.400 (10,20)
0.355 (9,00)
0.015 (0,38)
0.023 (0,58)
0.063 (1,60)
0.015 (0,38)
0.200 (5,08) MAX
0.130 (3,30) MIN
0.245 (6,22)
0.280 (7,11)
0.100 (2,54)
0
15
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification only on press ceramic glass frit seal only.
E. Falls within MIL-STD-1835 GDIP1-T8
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
44
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
MECHANICAL INFORMATION
N (R-PDIP-T**)
PLASTIC DUAL-IN-LINE PACKAGE
20
0.975
(24,77)
0.940
(23,88)
18
0.920
0.850
14
0.775
0.745
(19,69)
(18,92)
16
0.775
(19,69)
(18,92)
0.745
A MIN
DIM
A MAX
PINS **
0.310 (7,87)
0.290 (7,37)
(23.37)
(21.59)
Seating Plane
0.010 (0,25) NOM
14/18 PIN ONLY
4040049/C 08/95
9
8
0.070 (1,78) MAX
A
0.035 (0,89) MAX
0.020 (0,51) MIN
16
1
0.015 (0,38)
0.021 (0,53)
0.200 (5,08) MAX
0.125 (3,18) MIN
0.240 (6,10)
0.260 (6,60)
M
0.010 (0,25)
0.100 (2,54)
0
15
16 PIN SHOWN
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001 (20 pin package is shorter then MS-001.)
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
45
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
MECHANICAL INFORMATION
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE PACKAGE
4040082 / B 03/95
0.310 (7,87)
0.290 (7,37)
0.010 (0,25) NOM
0.400 (10,60)
0.355 (9,02)
5
8
4
1
0.020 (0,51) MIN
0.070 (1,78) MAX
0.240 (6,10)
0.260 (6,60)
0.200 (5,08) MAX
0.125 (3,18) MIN
0.015 (0,38)
0.021 (0,53)
Seating Plane
M
0.010 (0,25)
0.100 (2,54)
0
15
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
46
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
MECHANICAL INFORMATION
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
4040064 / E 08/96
14 PIN SHOWN
Seating Plane
1,20 MAX
1
A
7
14
0,19
4,50
4,30
8
6,20
6,60
0,30
0,75
0,50
0,25
Gage Plane
0,15 NOM
0,65
M
0,10
0
8
0,10
PINS **
A MIN
A MAX
DIM
2,90
3,10
8
4,90
5,10
14
6,60
6,40
4,90
5,10
16
7,70
20
7,90
24
9,60
9,80
28
0,15
0,05
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
47
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
MECHANICAL INFORMATION
U (S-GDFP-F10)
CERAMIC DUAL FLATPACK
4040179 / B 03/95
1.000 (25,40)
0.080 (2,03)
0.250 (6,35)
0.250 (6,35)
0.019 (0,48)
0.025 (0,64)
0.300 (7,62)
0.045 (1,14)
0.006 (0,15)
0.050 (1,27)
0.015 (0,38)
0.005 (0,13)
0.026 (0,66)
0.004 (0,10)
0.246 (6,10)
0.750 (19,05)
1
10
5
6
0.250 (6,35)
0.350 (8,89)
0.350 (8,89)
0.250 (6,35)
0.050 (1,27)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification only.
E. Falls within MIL STD 1835 GDFP1-F10 and JEDEC MO-092AA
TLV225x, TLV225xA
Advanced LinCMOS
RAIL-TO-RAIL
VERY LOW-POWER OPERATIONAL AMPLIFIERS
SLOS185C FEBRUARY 1997 REVISED MARCH 2001
48
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
MECHANICAL INFORMATION
W (R-GDFP-F16)
CERAMIC DUAL FLATPACK
0.235 (5,97)
0.355 (9,02)
0.355 (9,02)
0.235 (5,97)
9
8
16
1
0.745 (18,92)
0.245 (6,22)
0.004 (0,10)
0.026 (0,66)
0.015 (0,38)
0.015 (0,38)
0.045 (1,14)
0.371 (9,42)
0.006 (0,15)
0.045 (1,14)
Base and Seating Plane
0.025 (0,64)
0.019 (0,48)
0.440 (11,18)
0.285 (7,24)
0.085 (2,16)
1.025 (26,04)
4040180-3 / B 03/95
0.275 (6,99)
0.305 (7,75)
0.050 (1,27)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification only.
E. Falls within MIL-STD-1835 GDFP1-F16 and JEDEC MO-092AC
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package
Type
Package
Drawing
Pins Package
Qty
Eco Plan
(2)
Lead/Ball Finish
MSL Peak Temp
(3)
5962-9550401Q2A
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
Level-NC-NC-NC
5962-9550401QHA
ACTIVE
CFP
U
10
1
TBD
A42 SNPB
Level-NC-NC-NC
5962-9550401QPA
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
Level-NC-NC-NC
5962-9550403Q2A
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
Level-NC-NC-NC
5962-9550403QHA
ACTIVE
CFP
U
10
1
TBD
A42 SNPB
Level-NC-NC-NC
5962-9550403QPA
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
Level-NC-NC-NC
TLV2252AID
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2252AIDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2252AIDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2252AIP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
Level-NC-NC-NC
TLV2252AIPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
Level-NC-NC-NC
TLV2252AIPW
ACTIVE
TSSOP
PW
8
150
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2252AIPWG4
ACTIVE
TSSOP
PW
8
150
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2252AIPWLE
OBSOLETE
TSSOP
PW
8
TBD
Call TI
Call TI
TLV2252AIPWR
ACTIVE
TSSOP
PW
8
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2252AQD
ACTIVE
SOIC
D
8
75
Pb-Free
(RoHS)
CU NIPDAU
Level-2-250C-1 YEAR/
Level-1-235C-UNLIM
TLV2252AQDR
ACTIVE
SOIC
D
8
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-2-250C-1 YEAR/
Level-1-235C-UNLIM
TLV2252CP
ACTIVE
PDIP
P
8
TBD
Call TI
Call TI
TLV2252ID
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2252IDG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2252IDR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2252IDRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2252IP
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
Level-NC-NC-NC
TLV2252IPE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
Level-NC-NC-NC
TLV2252QD
ACTIVE
SOIC
D
8
75
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2252QDR
ACTIVE
SOIC
D
8
2500
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2254AID
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2254AIDG4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2254AIDR
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
PACKAGE OPTION ADDENDUM
www.ti.com
13-Sep-2005
Addendum-Page 1
Orderable Device
Status
(1)
Package
Type
Package
Drawing
Pins Package
Qty
Eco Plan
(2)
Lead/Ball Finish
MSL Peak Temp
(3)
TLV2254AIN
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPD
Level-NC-NC-NC
TLV2254AINE4
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPD
Level-NC-NC-NC
TLV2254AIPW
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2254AIPWG4
ACTIVE
TSSOP
PW
14
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2254AIPWLE
OBSOLETE
TSSOP
PW
14
TBD
Call TI
Call TI
TLV2254AIPWR
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2254AIPWRG4
ACTIVE
TSSOP
PW
14
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2254AQD
ACTIVE
SOIC
D
14
50
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2254AQDR
ACTIVE
SOIC
D
14
2500
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2254ID
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2254IDR
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2254IDRG4
ACTIVE
SOIC
D
14
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2254IN
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPD
Level-NC-NC-NC
TLV2254INE4
ACTIVE
PDIP
N
14
25
Pb-Free
(RoHS)
CU NIPD
Level-NC-NC-NC
TLV2254QD
ACTIVE
SOIC
D
14
50
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2254QDR
ACTIVE
SOIC
D
14
2500
TBD
CU NIPDAU
Level-1-220C-UNLIM
TLV2262AMFKB
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
Level-NC-NC-NC
TLV2262AMJGB
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
Level-NC-NC-NC
TLV2262AMUB
ACTIVE
CFP
U
10
1
TBD
A42 SNPB
Level-NC-NC-NC
TLV2262MFKB
ACTIVE
LCCC
FK
20
1
TBD
POST-PLATE
Level-NC-NC-NC
TLV2262MJGB
ACTIVE
CDIP
JG
8
1
TBD
A42 SNPB
Level-NC-NC-NC
TLV2262MUB
ACTIVE
CFP
U
10
1
TBD
A42 SNPB
Level-NC-NC-NC
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco
Plan
-
The
planned
eco-friendly
classification:
Pb-Free
(RoHS)
or
Green
(RoHS
&
no
Sb/Br)
-
please
check
http://www.ti.com/productcontent
for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
PACKAGE OPTION ADDENDUM
www.ti.com
13-Sep-2005
Addendum-Page 2
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com
13-Sep-2005
Addendum-Page 3
MECHANICAL DATA
MCER001A JANUARY 1995 REVISED JANUARY 1997
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
JG (R-GDIP-T8)
CERAMIC DUAL-IN-LINE
0.310 (7,87)
0.290 (7,37)
0.014 (0,36)
0.008 (0,20)
Seating Plane
4040107/C 08/96
5
4
0.065 (1,65)
0.045 (1,14)
8
1
0.020 (0,51) MIN
0.400 (10,16)
0.355 (9,00)
0.015 (0,38)
0.023 (0,58)
0.063 (1,60)
0.015 (0,38)
0.200 (5,08) MAX
0.130 (3,30) MIN
0.245 (6,22)
0.280 (7,11)
0.100 (2,54)
0
15
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification.
E. Falls within MIL STD 1835 GDIP1-T8
MECHANICAL DATA
MCFP001A JANUARY 1995 REVISED DECEMBER 1995
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
U (S-GDFP-F10)
CERAMIC DUAL FLATPACK
4040179 / B 03/95
0.080 (2,03)
0.250 (6,35)
0.019 (0,48)
4 Places
0.300 (7,62) MAX
0.045 (1,14)
0.008 (0,20)
0.050 (1,27)
0.015 (0,38)
0.005 (0,13) MIN
0.026 (0,66)
0.004 (0,10)
0.246 (6,10)
1
10
5
6
0.250 (6,35)
0.350 (8,89)
0.350 (8,89)
0.250 (6,35)
0.050 (1,27)
Base and Seating Plane
0.280 (7,11)
0.230 (5,84)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification only.
E. Falls within MIL STD 1835 GDFP1-F10 and JEDEC MO-092AA
MECHANICAL DATA
MLCC006B OCTOBER 1996
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
FK (S-CQCC-N**)
LEADLESS CERAMIC CHIP CARRIER
4040140 / D 10/96
28 TERMINAL SHOWN
B
0.358
(9,09)
MAX
(11,63)
0.560
(14,22)
0.560
0.458
0.858
(21,8)
1.063
(27,0)
(14,22)
A
NO. OF
MIN
MAX
0.358
0.660
0.761
0.458
0.342
(8,69)
MIN
(11,23)
(16,26)
0.640
0.739
0.442
(9,09)
(11,63)
(16,76)
0.962
1.165
(23,83)
0.938
(28,99)
1.141
(24,43)
(29,59)
(19,32)
(18,78)
**
20
28
52
44
68
84
0.020 (0,51)
TERMINALS
0.080 (2,03)
0.064 (1,63)
(7,80)
0.307
(10,31)
0.406
(12,58)
0.495
(12,58)
0.495
(21,6)
0.850
(26,6)
1.047
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.035 (0,89)
0.010 (0,25)
12
13
14
15
16
18
17
11
10
8
9
7
5
4
3
2
0.020 (0,51)
0.010 (0,25)
6
1
28
26
27
19
21
B SQ
A SQ
22
23
24
25
20
0.055 (1,40)
0.045 (1,14)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a metal lid.
D. The terminals are gold plated.
E. Falls within JEDEC MS-004
MECHANICAL DATA
MPDI001A JANUARY 1995 REVISED JUNE 1999
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE
8
4
0.015 (0,38)
Gage Plane
0.325 (8,26)
0.300 (7,62)
0.010 (0,25) NOM
MAX
0.430 (10,92)
4040082/D 05/98
0.200 (5,08) MAX
0.125 (3,18) MIN
5
0.355 (9,02)
0.020 (0,51) MIN
0.070 (1,78) MAX
0.240 (6,10)
0.260 (6,60)
0.400 (10,60)
1
0.015 (0,38)
0.021 (0,53)
Seating Plane
M
0.010 (0,25)
0.100 (2,54)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm
MECHANICAL DATA
MTSS001C JANUARY 1995 REVISED FEBRUARY 1999
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,65
M
0,10
0,10
0,25
0,50
0,75
0,15 NOM
Gage Plane
28
9,80
9,60
24
7,90
7,70
20
16
6,60
6,40
4040064/F 01/97
0,30
6,60
6,20
8
0,19
4,30
4,50
7
0,15
14
A
1
1,20 MAX
14
5,10
4,90
8
3,10
2,90
A MAX
A MIN
DIM
PINS **
0,05
4,90
5,10
Seating Plane
0
8
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI's terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright
2005, Texas Instruments Incorporated
PDF 
ZIP