UNIVERSAL INPUT AC-DC PCB OPEN FRAME SINGLE &
DUAL OUTPUT 13-15 WATTS INTERNAL SWITCHING
POWER SUPPLIES TPVI13 SERIES
FEATURES:
ACCOMMODATE UNIVERSAL AC SOURCES
LOW-PROFILE & COMPACT PCB FORMAT
MEET UNIVERSAL SAFETY STANDARDS
EMI MEET CISPR PUB. 22 & FCC CLASS B
CE MARKING COMPLIANCE
OUTPUT SPECIFICATION
Output Voltage: See Ratings Chart.
Output Current: See Ratings Chart.
Output Wattage: Typ. 13-15watts.
Output Connector: Molex # 5045.
Line Regulation: Typ. 0.1%.
Load Regulation: Main VO1 typ. 2.0%.
Aux. VO2 typ. 5.0% (stacked on).
Noise & Ripple: Typ. 1.0% peak to peak.
OVP: Built-in at VO1 (Zener diode).
Adjustability: Available at VO1.
Overload Protection (OLP):
Fully protected against output overload and short circuit.
OLP set at about 125-150% rating output wattage.
Consult the factory for OLP setting.
SPECIFICATION
INPUT SPECIFICATION
Input Voltage: Range typ. 90-264Vac.
Rating 100 to 240Vac.
Input Connector: Molex # 5045.
Input Frequency: 47-63Hz
Inrush Current: Typ. 26.0A @230Vac.
Input Current: Typ. 0.30A @115Vac, 0.15A@230Vac.
Dielectric Withstand: Meet IEC 60950-1.
EMI: Meet CISPR PUB. 22 & FCC Class B.
Hold-up Time: Typ. 10mS @115Vac, 40mS @230Vac.
Earth Leakage: Typ. 0.25mA @230Vac.
GENERAL SPECIFICATION
Efficiency: Typ. 70-80%.
Switching Frequency: 40 KHz.
Circuit Topology: Fixed Frequency Flyback Circuit.
Transient Response: Output voltage returns in
less than 3mS following
a 25% load change.
Safety Standard: IEC 60950-1/UL 60950-1 Class II.
Operating Temperature: 0 to +50C.
Storage Temperature: -20 to +85C.
Temperature Coefficient: Typ. 0.04%/C.
Cooling: Free air convection.
Construction: PCB open frame format.
Power Density: 2.12 Watts / Cubic Inch.
Note: Due to requests in market and advances in technology, specifications subject to change without notification.
TOTAL POWER INT'L
OUTPUT VOLTAGE / CURRENT RATINGS CHART
MECHANICAL DIMENSIONS: MM [INCHES] WEIGHT: 62.0g (2.19 Oz.)
SINGLE OUTPUT
MAIN VO1
MODEL NO.
Typ.
Volt
Peak
TPVI13-S033030 3.0A 3.3V 3.7A
TPVI13-S050028 2.8A 5.0V 3.4A
TPVI13-S120012 1.2A 12.0V 1.5A
TPVI13-S150010 1.0A 15.0V 1.2A
TPVI13-S240006 0.6A 24.0V 0.8A
TPVI13-S480003 0.3A 48.0V 0.4A
DUAL OUTPUT
MAIN VO1
AUX. VO2
MODEL NO.
Typ.
Volt.
Max. Typ. Volt.
Max.
TPVI13-D033I 2.5A +3.3V 3.5A 0.4A +12V 0.5A
TPVI13-D033K 2.5A +3.3V 3.5A 0.3A +15V 0.4A
TPVI13-D033M 2.5A +3.3V 3.5A 0.2A +24V 0.2A
TPVI13-D050I 2.0A +5.0V 2.5A 0.4A +12V 0.5A
TPVI13-D050K 2.0A +5.0V 2.5A 0.3A +15V 0.4A
TPVI13-D050M 2.0A +5.0V 2.5A 0.2A +24V 0.2A
Symbol: " " OVP built-in. "" Stacked on main output.
Remark: (1) At least 20% of typical main output current is required to maintain stated regulation.
(2) Peak output, less than 60 Sec. with 10% duty cycle.
(3) Max. current can't be drawn from all output at the same time.
INPUT & OUTPUT CONNECTORS PIN ASSIGNMENT
AC INPUT
SINGLE OUTPUT
DUAL OUTPUT
ASSIGNMENT AC-LINE
AC-NEUTRAL
+VO1 DC-COM VO1
VO2 DC-COM
CONNECTOR & PIN #
P1-L P1-N P2-4,5 P2-1,2 P2-4,5 P2-3 P2-1,2
Mating connector: Molex 5051series or equivalent.
PDF 
ZIP